Ross Vision 4800DR-324-02 Bedienungsanleitung
Ross Video Limited
8-Keyer Module
Installation Guide
V I S I O N
2
Vision • 8-Keyer Module Installation Guide
• Ross Part Number: 4800DR-324-02
• Release Date: May 6, 2011. Printed in Canada.
The information contained in this guide is subject to change without notice or
obligation.
Copyright
© 2011 Ross Video Limited. All rights reserved.
Contents of this publication may not be reproduced in any form without the
written permission of Ross Video Limited. Reproduction or reverse engineering
of copyrighted software is prohibited.
Patents
This product is protected by the following US Patents: 4,205,346; 5,115,314;
5,280,346; 5,561,404; 7,034,886; 7,508,455; 7,602,446; 7,834,886. This
product is protected by the following Canadian Patents: 2039277; 1237518;
1127289. Other patents pending.
Notice
The material in this guide is furnished for informational use only. It is subject to
change without notice and should not be construed as commitment by Ross
Video Limited. Ross Video Limited assumes no responsibility or liability for
errors or inaccuracies that may appear in this guide.
Trademarks
• is a trademark of Ross Video Limited.
• Ross, ROSS, ROSS®, MLE, Vision, and Octane are registered or
unregistered trademarks of Ross Video Limited.
• All other product names and any registered and unregistered
trademarks mentioned in this guide are used for identification
purposes only and remain the exclusive property of their
respective owners.
3
Important Regulatory and Safety Notices to Service
Personnel
Before using this product and any associated equipment, refer to the
“Important Safety Instructions” listed in the front of your Engineering
Manual to avoid personnel injury and to prevent product damage.
Product may require specific equipment, and/or installation procedures to be
carried out to satisfy certain regulatory compliance requirements. Notices have
been included in this publication to call attention to these specific requirements.
General Handling Guidelines
• Careful handling, using proper ESD precautions, must be observed.
• Power down the system before PCB removal.
ESD Susceptibility — Avoid handling the switcher circuit
boards in high static environments such as carpeted areas, and
when synthetic fiber clothing is worn. Touch the frame to
dissipate static charge before removing boards from the frame,
and exercise proper grounding precautions when working on
circuit boards.
Environmental Information
The equipment that you purchased required the extraction and use
of natural resources for its production. It may contain hazardous
substances that could impact health and the environment.
To avoid the potential release of those substances into the environment and to
diminish the need for the extraction of natural resources, Ross Video encourages
you to use the appropriate take-back systems. These systems will reuse or
recycle most of the materials from your end-of-life equipment in an
environmentally friendly and health conscious manner.
The crossed-out wheeled bin symbol invites you to use these systems.
If you need more information on the collection, reuse, and recycling systems,
please contact your local or regional waste administration.
You can also contact Ross Video for more information on the environmental
performances of our products.
4 • Package Contents
Package Contents
The contents of a single 8-Keyer Module upgrade kit is listed below. If any
items are missing, or damaged, contact Ross Video Technical Support.
Qty Part# Item
1 4800AR-127A 8-Keyer Module
1727-024R Module Control Link Cable (Black, CAT5e)
8-Keyer Module Installation • 5
8-Keyer Module Installation
To install the 8-Keyer module for the Vision control panel, you must power
down the control panel, disconnect the communications cables, remove the
Keyer module, install the new module, and then connect the power and
communications cables.
A single 8-Keyer module can be installed in the control panel.
Use the following procedure to install the 8-Keyer module:
1. Power down the control panel. The frame can remain on during this
procedure. Refer to your switcher documentation for information on
shutting down the switcher.
2. Unplug the Primary and Redundant (if installed) power from the
control panel.
Warning Hazardous Voltage — Hazardous voltages are
present in the control panel as long as any of the power supplies
are connected to the AC power.
3. Lift up on the control panel lid to gain access to the control panel tub.
4. Identify the Keyer module that you want to replace with the 8-Keyer
module. This should be the control panel row that is assigned as the
Program/Preset row.
5. Disconnect the Module Power Cable from the Keyer module you
want to remove (Figure 1). This 4-conductor ribbon cable delivers
power to all the modules in the row. When removing it, ensure that
you do not accidently unplug it from any neighboring modules.
Figure 1 Power Connector — 6-Keyer Module
6. Disconnect the Module Control Link Cables from the Keyer module
you want to remove. These CAT5e cables deliver all the command
PMC Board
To Front of Control Panel
Power Connector
6 • 8-Keyer Module Installation
signals to and from the module, as well as the other modules in the
same row.
7. Remove the Retaining Bolts located at each corner of the Keyer
module and keep them in a safe place. A ¼ inch hex driver or wrench
is required.
8. Remove the Keyer module plate from the control panel.
9. Slide the 8-Keyer module into the module opening.
10. Install the Retaining Bolts located at each corner of the module to a
maximum torque of 5 in-lbs (6 cm-kg). A ¼ inch hex driver or
wrench is required.
11. Connect and secure the Module Control Link Cables to the PMC on
the 8-Keyer module (Figure 2). One cable connects to the previous
module in the row, and the other cable to the next module.
Figure 2 Panel Module Controller (PMC) — Module Control Link Connectors
12. Connect and secure the Module Power Cable to the 8-Keyer module
(Figure 3).
Figure 3 Power Connector — 8-Keyer Module
13. Close the control panel lid and reconnect the power supplies.
This completes the procedure for installing the 8-Keyer module.
To Next Module
Module Control
Link Connectors
To Previous Module
PMC Board
To Front of Control Panel
Power Connector
8-Keyer Module Setup • 7
8-Keyer Module Setup
With the 8-Keyer module installed and cabled, the Vision switcher must
be set up to properly communicate with the 8-Keyer module.
Refer to your Vision Engineering Manual for information on upgrading
your PMCs and assigning the 8-Keyer module to a panel row.
Contact Us
Contact our friendly and professional support representatives for the
following:
• Name and address of your local dealer
• Product information and pricing
• Technical support
• Upcoming trade show information
Visit Us
Please visit us at our website for:
• Company information
• Related products and full product lines
• On-line catalog
•News
• Testimonials
PHONE
General Business Office
and Technical Support 613 • 652 • 4886
After Hours Emergency 613 • 349 • 0006
Fax 613 • 652 • 4425
E-MAIL General Information [email protected]
POSTAL
SERVICE
Ross Video Limited 8 John Street,
Iroquois, Ontario, Canada
K0E 1K0
Ross Video Incorporated P.O. Box 880,
Ogdensburg, New York, USA
13669-0880
Inhaltsverzeichnis
Andere Ross Steuereinheit Handbücher
Ross
Ross AVFR-7564 Bedienungsanleitung
Ross
Ross W60 Series Bedienungsanleitung
Ross
Ross DM1 C Bedienungsanleitung
Ross
Ross Serpar 35 Series Bedienungsanleitung
Ross
Ross 21 Series Bedienungsanleitung
Ross
Ross DM2E Bedienungsanleitung
Ross
Ross W74 Series Bedienungsanleitung
Ross
Ross DM2 C Series Bedienungsanleitung
Ross
Ross RSe Series Bedienungsanleitung
Ross
Ross SideBox Handbuch
Ross
Ross Serpar 35 Series Bedienungsanleitung
Ross
Ross HBB Series Bedienungsanleitung
Ross
Ross M DM2 C Series Bedienungsanleitung
Ross
Ross HDBH Series Bedienungsanleitung
Ross
Ross CrossMirror CM26 Series Bedienungsanleitung
Ross
Ross DM2 Series Bedienungsanleitung
Ross
Ross Vision 4800DR-325-02 Bedienungsanleitung
Ross
Ross Serpar 35 Series Bedienungsanleitung
Ross
Ross CrossCheck CC4 Series Bedienungsanleitung
Ross
Ross W64 Series Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
