Rotary SPOA7 Series Handbuch

SPOA7 With Movable Pads

Capacity 7,000 lbs.

Rev. A 5/5/2014

LP20314

Table of Contents

Safety Instructions................................................................................................................................2

Owner/Employer Responsibilities ......................................................................................................3

Operating Instructions .........................................................................................................................4

Maintenance Instructions...................................................................................................................6

Trouble Shooting ...................................................................................................................................7

Lift Lockout/Tagout Procedure ...........................................................................................................8

Operating Conditions............................................................................................................................9

Approved Accessories.........................................................................................................................9

Installer: Please return this booklet to literature package and give to lift owner/operator.

• Daily inspect your lift. Never operate if it malfunctions or if it

has broken or damaged parts. Use only qualiﬁed lift service

personnel and genuine Rotary parts to make repairs.

• Thoroughly train all employees in use and care of lift, using

manufacturer’s instructions and “Lifting It Right” and “Safety

Tips” supplied with the lift.

• Never allow unauthorized or untrained persons to position

vehicle or operate lift.

• Prohibit unauthorized persons from being in shop area while lift

is in use.

• Do Not permit anyone on lift or inside vehicle when it is either

being raised or lowered.

• Always keep area around lift free of tools, debris, grease and

oil.

• Never overload lift. Capacity of lift is shown on nameplate

afﬁxed to the lift.

• Do Not stand in front of the vehicle while it is being positioned

in lift bay.•

• Before driving vehicle into lift bay, BE SURE lift is fully lowered.

• Do Not hit or run over lift arms or adapters. This could damage

lift or vehicle. Before driving vehicle into lift bay, position arms

and adapters to provide unobstructed entrance onto lift.

• Load vehicle on lift carefully. Position lift adapters to contact

at the vehicle manufacturer’s recommended lift points. Raise

lift until adapters contact vehicle. Check adapters for secure

contact with vehicle. Raise lift to desired working height.

CAUTION

DO NOT go under vehicle if locking latches are not

engaged.

• Do Not block open or override self-closing lift controls; they

are designed to return to the “Off” or Neutral position when

released.

• Do Not remove or disable arm restraints.

• Remain clear of lift when raising or lowering vehicle.

• Always use safety stands when removing or installing heavy

components.

• Avoid excessive rocking of vehicle while on lift.

• Clear area if vehicle is in danger of falling.

• Remove tool trays, stands, etc. before lowering lift.

• Release locking latches before attempting to lower lift.

• Position lift arms and adapters to provide an unobstructed exit

before removing vehicle from lift area.

Authorized personnel

only in lift area.

CAUTION

Read operating

and safety manuals

before using lift.

SAFETY

INSTRUCTIONS

WARNING

Position vehicle

with center of gravity

midway between

adapters.

CAUTION

Use vehicle

manufacturer’s

lift points.

WARNING

Do not override

self-closing

lift controls.

Keep feet

clear of lift

while lowering.

WARNING

Remain clear of lift

when raising or

lowering vehicle.

CAUTION

Always use

safety stands when

removing or installing

heavy components. ©

WARNING

Avoid excessive

rocking of vehicle

while on lift.

WARNING

Clear area if vehicle

is in danger of falling.

CAUTION

Auxiliary adapters

may reduce

load capacity.

SAFETY

INSTRUCTIONS

Do not operate

a damaged lift.

CAUTION

Lift to be used

by trained operator

only.

SAFETY

INSTRUCTIONS

Proper maintenance

and inspection

is necessary

for safe operation.c

SAFETY INSTRUCTIONS

OWNER/EMPLOYER RESPONSIBILITIES

The Owner/Employer:

• Shall ensure that lift operators are qualiﬁed and that they are trained in the safe

use and operation of the lift using the manufacturer’s operating instructions;

ALI/SM07-1, ALI Lifting it Right safety manual; ALI/ST-05 ALI Safety Tips card;

ANSI/ALI ALOIM-2008, American National Standard for Automotive Lifts-Safety

Requirements for Operation, Inspection and Maintenance; ALI/WL Series, ALI

Uniform Warning Label Decals/Placards; and in the case of frame engaging lifts,

ALI/LP-GUIDE, Vehicle Lifting Points/Quick Reference Guide for Frame Engaging

Lifts.

• Shall establish procedures to periodically inspect the lift in accordance with

the lift manufacturer’s instructions or ANSI/ALI ALOIM-2008, American National

Standard for Automotive Lifts-Safety Requirements for Operation, Inspection and

Maintenance; and The Employer Shall ensure that lift inspectors are qualiﬁed

and that they are adequately trained in the inspection of the lift.

• Shall establish procedures to periodically maintain the lift in accordance with

the lift manufacturer’s instructions or ANSI/ALI ALOIM-2008, American National

Standard for Automotive Lifts-Safety Requirements for Operation, Inspection and

Maintenance; and The Employer Shall ensure that lift maintenance personnel

are qualiﬁed and that they are adequately trained in the maintenance of the lift.

• Shall maintain the periodic inspection and maintenance records recommended

by the manufacturer or ANSI/ALI ALOIM-2008, American National Standard

for Automotive Lifts-Safety Requirements for Operation, Inspection and

Maintenance.

• Shall display the lift manufacturer’s operating instructions; ALI/SM07-1,

ALI Lifting it Right safety manual; ALI/ST-05 ALI Safety Tips card; ANSI/

ALI ALOIM-2008, American National Standard for Automotive Lifts-Safety

Requirements for Operation, Inspection and Maintenance; and in the case

of frame engaging lifts, ALI/LP-GUIDE, Vehicle Lifting Points/Quick Reference

Guide for Frame Engaging Lifts; in a conspicuous location in the lift area

convenient to the operator.

• Shall provide necessary lockout/tagout means for energy sources per ANSI

Z244.1-2003 (R2008), Safety Requirements for the Lockout/Tagout of Energy

Sources, before beginning any lift repairs.

• Shall not modify the lift in any manner without the prior written consent of the

manufacturer.

CAUTION

Lift to be used

by trained operator

only.

SAFETY

INSTRUCTIONS

Proper maintenance

and inspection

is necessary

for safe operation. c

Read operating

and safety manuals

before using lift.

SAFETY

INSTRUCTIONS

CAUTION DO NOT go under vehicle if locking latches

are not engaged.

5. While Using Lift:

A. Avoid excessive rocking of vehicle while on lift.

B. Always use safety stands as needed or when

removing or installing heavy components.

6. To Lower Lift:

A. Remove all tools or other objects from lift area.

B. Raise lift off locking latches.

C. Pull LATCH release handle fully and hold.

D. Push LOWERING valve handle to lower, Fig. 4.

Note: Both LATCH release and LOWERING valve handles

are deadman-type design. Each must be held down to

lower lift. Do not override self-closing lift controls.

7. Remain clear of lift when lowering vehicle. Observe

pinch point warning decals.

8. Remove adapters from under vehicle. Be sure lift is fully

lowered before removing vehicle.

9. If lift is not operating properly, Do Not use until

adjustment or repairs are made by qualiﬁed lift service

personnel.

SPOA7 M-PAD OPERATING INSTRUCTIONS

To avoid personal injury and/or property damage, permit only trained personnel to operate lift.

After reviewing these instructions, get familiar with lift controls by running the lift through a

few cycles before loading vehicle on lift.

Always lift the vehicle using all four adapters. NEVER raise just one end, one corner, or one side

of vehicle.

Authorized personnel

only in lift area.

CAUTION

Read operating

and safety manuals

before using lift.

SAFETY

INSTRUCTIONS

CAUTION

Lift to be used

by trained operator

only.

CAUTION

Use height extenders

when necessary

to ensure

good contact. ©

CAUTION

Use vehicle

manufacturer’s

lift points.

CAUTION

Auxiliary adapters

may reduce

load capacity.

WARNING

Remain clear of lift

when raising or

lowering vehicle.

CAUTION

Always use

safety stands when

removing or installing

heavy components. ©

WARNING

Do not override

self-closing

lift controls.

WARNING

Remain clear of lift

when raising or

lowering vehicle.

Observe and heed SAFETY, CAUTION and WARNING labels

on the lift.

1. Lift must be fully lowered and

service bay clear of all personnel

before the vehicle is brought on

lift. Swing arms out to full drive-thru

position.

2. Spot vehicle over lift with left front

wheel in proper spotting dish position,

Fig. 5. Be sure vehicle wheels and/or

mud ﬂaps clear pad end ramps.

3. Loading: DO NOT raise limousines

or pickup trucks. DO NOT raise SUV's,

vans, or other specialty vehicles not of

a unibody construction.

Before lifting vehicle be sure that:

A. Pads are in secure contact with

frame or support structure at outer

body.

B. Certain vehicles such as Camaro,

Firebird, Escort, or Chrysler "K" Cars or

others may require additional clearance under carriage

or exhaust system from contacting pad support. Use

3" high auxiliary rubber pads. Locate under frame

or support structure at outer body using vehicle

manufacturer's recommended pick up points.

Note: Allow 2 seconds between motor starts. Failure to

comply may cause motor burnout.

4. To Raise Lift:

A. Push RAISE switch on power unit, Fig. 4.

B. Stop before making contact with vehicle. Be sure

wheels and/or mud ﬂaps clear pad end ramps.

C. Raise vehicle until tires clear the ﬂoor.

D. Stop and check pads for secure contact at vehicle

manufacturer’s recommended lift points.

E. Continue to raise to desired height only if vehicle is

secure on lift.

F. Repeat complete spotting, loading and raising

procedures if required.

H. Lower lift onto locking latches.

IMPORTANT

WARNING

Clear area if vehicle

is in danger of falling.

Vehicle Spotting Position

Vehicle Loading Position

FRONT

LIFT

POINTS

FRONT

LIFT

POINTS

FRONT

LIFT

POINTS

FRONT

LIFT

POINTS

Pickup Truck

Perimeter Frame

Unitized Body

Stub Frame

Keep feet

clear of lift

while lowering.

WARNING

SAFETY

INSTRUCTIONS

Do not operate

a damaged lift.

SAFETY

INSTRUCTIONS

Proper maintenance

and inspection

is necessary

for safe operation.c

SAFETY

INSTRUCTIONS

Proper maintenance

and inspection

is necessary

for safe operation.c

Less than 105"

wheelbase:

position left front

wheel on approach

side of wheel dish.

105"-127"

wheelbase:

position left front

wheel in wheel

dish.

Larger than 127"

wheelbase:

position left front

wheel just forward

of wheel dish.

NOTE: Some vehicles may have the manufacturer's

Service Garage Lift Point locations identiﬁed by

triangle shape marks on it's undercarriage. Also,

there may be a label located on the right front door

lock face showing speciﬁc vehicle lift points. If the

speciﬁc vehicle lift points are not identiﬁed, refer to

the "Typical Lift Points" illustrated herein. ALWAYS

follow the operating instructions supplied with the

lift.

NOTE: This style lift is not

recommended for pickup trucks or

vehicles with truck frames.

Typical Lifting Points

Fig. 5

CAUTION

Fig. 6

Latch

Release Raise

Switch

Lowering Valve

Handle

Latch

Release

Raise

Switch

Lowering Valve

Handle

Fig. 4

CAUTION

Lift to be used

by trained operator

only.

CAUTION

Always use

safety stands when

removing or installing

heavy components. ©

The messages and pictographs shown are generic in nature and are meant

to generally represent hazards common to all automotive lifts regardless of

specific style.

Funding for the development and validation of these labels was provided by

the Automotive Lift Institute, PO Box 33116 Indialantic, FL. 32903-3116.

They are protected by copyright. Set of labels may be obtained from ALI or

its member companies.

ALI/WL101cÓ1992 by ALI, Inc.

Authorized personnel

only in lift area.

CAUTION

Use vehicle

manufacturer’s

lift points.

CAUTION

Use height extenders

when necessary

to ensure

good contact. ©

CAUTION

Auxiliary adapters

may reduce

load capacity.

If you are not completely familiar with automotive lift maintenance

procedures; STOP: Contact factory for instructions. To avoid

personal injury, permit only qualiﬁed personnel to perform

maintenance on this equipment.

• Always keep bolts tight. Check periodically.

• Always keep lift components clean.

• Always if oil leakage is observed, call local service

representative.

• Always if electrical problems develop, call local service

representative.

• Daily: Check cables and sheaves for wear. Observe for frayed

cable strands. Wipe cables with a rag to detect hard to see

small broken cable strands. Replace cables showing any

broken strands. Replace worn parts as required with genuine

Rotary parts.

• Daily: Inspect rubber pads for damage or excessive wear.

Replace as required with genuine Rotary parts.

• Daily: Inspect adapters for damage or excessive wear.

Replace as required with genuine Rotary parts.

• Monthly: Check equalizer cable tension. Adjust per lift

installation instructions. If there are no more threads available

for adjustment, replace the cable. Do not use washers to

stand off the nut to use previously used threads.

• Monthly: Lubricate locking latch shafts. Push latch handle

several times for oil to penetrate pivot points.

• Every 3 Months: Check anchor bolts for tightness. Anchors

should be torqued to 65 ft/lbs.

• Semi-Annually: Check ﬂuid level of lift power unit and reﬁll if

required per lift installation instructions.

• If Lift stops short of full rise or chatters, check ﬂuid level and

bleed both cylinders per lift installation instructions.

INSPECTION and MAINTENANCE

See ANSI/ALI ALOIM booklet for periodic

inspection checklist and maintenance

log sheet.

SAFETY

INSTRUCTIONS

Do not operate

a damaged lift.

Read operating

and safety manuals

before using lift.

SAFETY

INSTRUCTIONS

The messages and pictographs

shown are generic in nature and

are meant to generally represent

hazards common to all automotive

lifts regardless of specific style.

Funding for the development and

validation of these labels was

provided by the Automotive Lift

Institute, PO Box 33116 Indialantic,

FL. 32903-3116.

They are protected by copyright.

Set of labels may be obtained from

ALI or its member companies.

C 1992 by ALI, Inc. ALI/WL101s

SAFETY

INSTRUCTIONS

Proper maintenance

and inspection

is necessary

for safe operation. c

WARNING

Clear area if vehicle

is in danger of falling.

The messages and pictographs shown are generic in nature and are meant

to generally represent hazards common to all automotive lifts regardless of

specific style.

Funding for the development and validation of these labels was provided by

the Automotive Lift Institute, PO Box 33116 Indialantic, FL. 32903-3116.

They are protected by copyright. Set of labels may be obtained from ALI or

its member companies.

ALI/WL101wÓ1992 by ALI, Inc.

WARNING

Position vehicle

with center of gravity

midway between

adapters.

WARNING

Remain clear of lift

when raising or

lowering vehicle.

Keep feet

clear of lift

while lowering.

WARNING

Do not override

self-closing

lift controls.

WARNING

Avoid excessive

rocking of vehicle

while on lift.

MAINTENANCE INSTRUCTIONS

• Replace all caution, warning or safety

related decals on the lift if unable to read

or missing. Reorder labels from Rotary

Lift.

Trouble

Motor does not run.

Motor runs but will not raise lift.

Motor runs—raises unloaded lift but will

not raise vehicle.

Lift slowly settles down.

Slow lifting speed or oil blowing out ﬁller

breather cap.

Lift going up unlevel.

Anchors will not stay tight.

Locking latches do not engage.

Locking latches do not disengage.

Lift stops short of full rise or chatters.

Remedy

1. Replace blown fuse or reset circuit

breaker.

2. Supply correct voltage to motor.

3. Repair and insulate all connections.

4. Replace switch.

5. Replace switch.

6. Replace motor.

1. Repair or replace lowering valve.

2. Tighten all suction line ﬁttings.

3. Replace suction stub.

4. Fill tank to proper level with ISOVG32

Hydraulic Oil or Dexron III ATF.

1. Supply correct voltage to motor.

2. Clean lowering valve.

3. Replace relief valve cartridge.

4. Check vehicle weight and/or balance

vehicle weight on lift.

1. Clean check valve.

2. Clean lowering valve.

3. Repair external leaks.

1. Change oil using ISOVG32 Hydraulic Oil

or Dexron III ATF.

2. Tighten all suction line ﬁttings.

3. Reinstall oil return tube.

1. Adjust equalizer cables to correct

tension.

2. Shim lift to level columns (Not to

exceed 1/2”). If over 1/2” break out

ﬂoor and repour per lift installation

instructions.

1. Relocate lift using a new bit to

drill holes. Reference installation

instructions for minimum spacing

requirements.

2. Break out old concrete and repour

new pads for lift per lift installation

instructions.

1. Remove covers, oil latch mechanism.

Actuate latch release handle several

times to allow oil to coat shaft.

2. Replace broken spring.

3. Adjust clamp at cable end per lift

installation instructions.

1. Replace cable.

2. Check position of cable on sheaves/

upper guides; adjust cable tension.

3. Adjust cable tension.

1. Fill tank to proper level with ISOVG32

Hydraulic Oil or Dexron III ATF.

2. Bleed lift per installation instructions.

Cause

1. Blown fuse or circuit breaker.

2. Incorrect voltage to motor.

3. Bad wiring connections.

4. Motor up switch burned out.

5. Overhead limit switch burned out.

6. Motor windings burned out.

1. Open lowering valve.

2. Pump sucking air.

3. Suction stub off pump.

4. Low oil level.

1. Motor running on low voltage.

2. Debris in lowering valve.

3. Improper relief valve adjustment.

4. Overloading lift.

1. Debris in check valve seat.

2. Debris in lowering valve seat.

3. External oil leaks.

1. Air mixed with oil.

2. Air mixed with oil suction.

3. Oil return tube loose.

1. Equalizer cables out of adjustment.

2. Lift installed on unlevel ﬂoor.

1. Holes drilled oversize.

2. Concrete ﬂoor thickness or holding

strength not sufﬁcient.

1. Latch shafts rusted. (Usually occurs

on outside installations or in high

humidity areas such as vehicle wash

bays.)

2. Latch spring broken.

3. Latch cable needs adjustment.

1. Latch cable is broken.

2. Cable is off sheaves/upper guides.

3. Latch cable is loose.

1. Low oil level.

2. Air in hydraulic lines/cylinder.

TROUBLE SHOOTING

Purpose

This procedure establishes the minimum requirements for the lockout of energy that could cause injury to

personnel by the operation of lifts in need of repair or being serviced. All employees shall comply with this

procedure.

Responsibility

The responsibility for assuring that this procedure is followed is binding upon all employees and service

personnel from outside service companies (i.e., Authorized Rotary Installers, contactors, etc.). All employees

shall be instructed in the safety signiﬁcance of the lockout procedure by the facility owner/manager. Each

new or transferred employee along with visiting outside service personnel shall be instructed by the owner/

manager (or assigned designee) in the purpose and use of the lockout procedure.

Preparation

Employees authorized to perform lockout shall ensure that the appropriate energy isolating device (i.e.,

circuit breaker, fuse, disconnect, etc.) is identiﬁed for the lift being locked out. Other such devices for other

equipment may be located in close proximity of the appropriate energy isolating device. If the identity of the

device is in question, see the shop supervisor for resolution. Assure that proper authorization is received

prior to performing the lockout procedure.

Sequence of Lockout Procedure

1) Notify all affected employees that a lockout is being performed and the reason for it.

2) Unload the subject lift. Shut it down and assure the disconnect switch is “OFF” if one is provided on

the lift.

3) The authorized lockout person operates the main energy isolation device removing power to the

subject lift.

• If this is a lockable device, the authorized lockout person places the assigned padlock on

the device to prevent its unintentional reactivation. An appropriate tag is applied stating the

person’s name, at least 3” x 6” in size, an easily noticeably color, and states not to operate

device or remove tag.

• If this device is a non-lockable circuit breaker or fuse, replace with a “dummy” device and

tag it appropriately as mentioned above.

4) Attempt to operate lift to assure the lockout is working. Be sure to return any switches to the “OFF”

position.

5) The equipment is now locked out and ready for the required maintenance or service.

Restoring Equipment to Service

1) Assure the work on the lift is complete and the area is clear of tools, vehicles, and personnel.

2) At this point, the authorized person can remove the lock (or dummy circuit breaker or fuse) & tag

and activate the energy isolating device so that the lift may again be placed into operation.

Rules for Using Lockout Procedure

Use the Lockout Procedure whenever the lift is being repaired or serviced, waiting for repair when current

operation could cause possible injury to personnel, or for any other situation when unintentional operation

could injure personnel. No attempt shall be made to operate the lift when the energy isolating device is

locked out.

LIFT LOCKOUT/TAGOUT PROCEDURE

APPROVED ACCESSORIES

Item Capacity Part Number

Air/Electric Utility Box FA5911

Air/Electric Utility Box Without FRL FA5910

Filter/Regulator/Lubricator (FRL) FA5166

OPERATING CONDITIONS

Lift is not intended for outdoor use and has an operating ambient temperature range of

41º-104ºF (5º-40ºC).

NOTES

Andere Handbücher für SPOA7 Series

Inhaltsverzeichnis

Andere Rotary Hebesystem Handbücher

Rotary

Rotary SPOA10NB Series Bedienungsanleitung

Rotary

Rotary S42N46CAT-I Bedienungsanleitung

Rotary

Rotary SPOA7 Series Bedienungsanleitung

Rotary

Rotary Sprinter SPO15 Bedienungsanleitung

Rotary

Rotary 600 Series Handbuch

Rotary

Rotary 200 Series Bedienungsanleitung

Rotary

Rotary SM122-100 Series Bedienungsanleitung

Rotary

Rotary SL235MP Bedienungsanleitung

Rotary

Rotary XMB600 Handbuch

Rotary

Rotary S38AK-42CAT Handbuch

Rotary

Rotary 2000 Series Bedienungsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung

Rotary

Rotary SL212i 400 Series Handbuch

Rotary

Rotary SM40-47 Bedienungsanleitung

Rotary

Rotary MCH14 Series Bedienungsanleitung

Rotary

Rotary GEMINI 25-30-35 Bedienungsanleitung

Rotary

Rotary SGL35M Bedienungsanleitung

Rotary

Rotary 1000 SERIES Handbuch

Rotary

Rotary SM30 Bedienungsanleitung

Rotary

Rotary SPO12 Standard Bedienungsanleitung

Rotary

Rotary GAR324 Bedienungsanleitung

Rotary

Rotary Sprinter SPO15 Handbuch

Rotary

Rotary AR14 Bedienungsanleitung

Rotary

Rotary VLXS7 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Ricon

Ricon Mirage F9T Bedienungsanleitung