RS PRO ICM 134 Bedienungsanleitung

Instruction Manual

ICM 134

Clamp Meter

EN DE ES IT FR



EN - 2

Safety Information

Read and understand this Instruction

Manual completely before using this

instrument. Failure to observe the warnings

and cautions in this Instruction Manual may

result in injury or death, or damage to the

instrument and other equipment or

property.

If this instrument is used in a manner not

specified in these instructions, the protec-

tion provided by the instrument may be

impaired.

WARNING

-Examine the instrument and probes and

leads before use. Do not use the instru-

ment if it is wet or damaged, or if you

suspect it is not operating correctly.

-When using the instrument, test leads or

probes, keep your fingers behind the

finger guards.

-Remove the test lead from the instrument

before opening the battery cover or instru-

ment case.

-Always use the correct terminals, switch

position and range for measurements.

-Verify the instrument is operating correctly

by measuring a known voltage before

use. If in doubt, have the instrument

serviced.

-Do not apply more than the rated voltage

as marked on the instrument between

terminals, or between any terminal and

earth ground.

-Use caution when measuring voltages

above 30 Vac rms or 60 Vdc. These

voltages pose a shock hazard.

-To avoid incorrect readings that can lead

to electric shock, replace the battery as

soon as low battery indicator appears

in the display.

-Disconnect the circuit power and

discharge all high-voltage capacitors

before making resistance, continuity, or

diode measurements.

-Do not use the instrument in a Hazardous

Area or around explosive gasses or

vapours.

EN - 3

-Wear suitable Personal Protective

Equipment when working around or near

hazardous Live conductors which could

be accessible.

-Do not use the thermocouple to measure

the temperature of Hazardous Live

conductors or equipment.

Caution

-Disconnect the test leads from the test

points before changing the position of the

function rotary switch.

-Never connect the instrument to a source

of voltage with the function rotary switch in

Ω/ ;/Aposition.

- If possible, do not work alone, so

assistance can be given if required.

-Do not expose the instrument to extremes

of temperature or high humidity.

-If this instrument is used in the vicinity of

equipment which generates electro

magnetic interference, the display may

become unstable or the measurements

may be subject to large errors.

The following symbols may appear on

the instrument and in this Instruction

Manual:

Risk of electric shock

Refer to Instruction Manual

 Direct Current (dc)

Alternating Current (ac)

<Battery

Earth

Equipment protected throughout by

double or reinforced insulation

Conforms to EU directives

Dispose of this equipment in

accordance with local regulations.

EApplication around and removal

from hazardous Live conductors is

permitted.

EN - 4

Maintenance

Do not attempt to repair this Instrument. It

contains no user-serviceable parts. Repair

or servicing should only be performed by

qualified personnel. This instrument

should be calibrated yearly, or more

frequently if used in harsh conditions or if

it is suspected of being inaccurate.

For calibration and repair contact RS

Components - the address is given at the

end of these instructions.

Cleaning

Periodically wipe the case with a damp

cloth and detergent. Do not use abrasives

or solvents.

EN - 5

To conserve battery power, the Auto Power

-off function will turn the instrument off

approximately 10 minutes after the last

operation.

10min

To disable the Auto Power-off function:

Turn the instrument off, press and hold the

“Backlight” button and turn the rotary switch

to the required function. The auto Power-off

is disabled until the next time the instru-

ment is turned off and on again.

Power On / Off

Auto Power Off

EN - 6

ACV / DCV

Resistance

EN - 7

Diode / Continuity

;

EN - 8

DC µA

Capacitance

Note –To improve the measurement

accuracy of a small value capacitor, record

the reading with the test leads open circuit,

then substract the residual capacitance of

the Instrument and leads from the final

measurement.

CUNKNOWN =CMEASUREMENT - CRESIDUAL

EN - 9

Temperature

Data Hold

392A

EN - 10

ACA

392A

CAT.Ⅲ.600V

with respect to

earth for the jaw.

Tactile Barrier for

hand guard.

Do not hold

the meter across

the Tactile Barrier.

OK I + (-I) = 0

Back Light

Inhaltsverzeichnis

Andere RS PRO Messgerät Handbücher

RS PRO

RS PRO RS-3381 Bedienungsanleitung

RS PRO

RS PRO RS-5200 Bedienungsanleitung

RS PRO

RS PRO RS-9968BT Bedienungsanleitung

RS PRO

RS PRO RS-1013 Bedienungsanleitung

RS PRO

RS PRO IM-191 Bedienungsanleitung

RS PRO

RS PRO RS-1360A Bedienungsanleitung

RS PRO

RS PRO RS-8920 Bedienungsanleitung

RS PRO

RS PRO RS-96 Bedienungsanleitung

RS PRO

RS PRO IM-194 Bedienungsanleitung

RS PRO

RS PRO ISA-730 Bedienungsanleitung

RS PRO

RS PRO RS-8890G Bedienungsanleitung

RS PRO

RS PRO 123-8769 Bedienungsanleitung

RS PRO

RS PRO RS-128M Bedienungsanleitung

RS PRO

RS PRO RS-171V Bedienungsanleitung

RS PRO

RS PRO ILM 1335 Bedienungsanleitung

RS PRO

RS PRO RS-5322 Bedienungsanleitung

RS PRO

RS PRO IM-502 Bedienungsanleitung

RS PRO

RS PRO RSDPB5000 Series Bedienungsanleitung

RS PRO

RS PRO RSSA3000X Bedienungsanleitung

RS PRO

RS PRO RS 1400 Series Bedienungsanleitung

RS PRO

RS PRO LCR-6000 Series Bedienungsanleitung

RS PRO

RS PRO RS-90 Bedienungsanleitung

RS PRO

RS PRO RS-135 Bedienungsanleitung

RS PRO

RS PRO ICM A6N Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung