Ruijie RG-S2910-24GT4SFP-UP-H Installations- und Betriebsanleitung

RG-S2910-H Series Switch

Hardware Installation and Reference Guide V1.22

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,

modification, transmission, translation or commercial use of this document or any portion of this document,

in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.

Exemption Statement

This document is provided “as is”. The contents of this document are subject to change without any notice.

Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to

ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to

content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual will guide you through the installation of the device.

This manual describes the functional and physical features and provides the device installation steps,

hardware troubleshooting, module technical specifications, and specifications and usage guidelines for

cables and connectors.

Audience

It is intended for the users who have some experience in installing and maintaining network hardware. At

the same time, it is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

Ruijie Networks Website: http://www.ruijienetworks.com/

Service Email: [email protected]

Technical Support: http://www.ruijienetworks.com/service.aspx

Technical Support Hotline: +86-4008-111-000

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that

supported by the product, with configuration examples.

Command Reference

Describes the related configuration commands, including

command modes, parameter descriptions, usage guides, and

related examples.

Symbol Conventions

The symbols used in this document are described as below:

This symbol brings your attention to some helpful suggestions and references.

This symbol means that you must be extremely careful not to do some things that may damage the

device or cause data loss

1 Product Overview

The RG-S2910-H series switch is a next-generation intelligent switch that features high performance, high security,

multiple services and ease of use to meet the needs of the current networks. The RG-S2910-H series switch can provide

the complete end-to-end Quality of Service (QoS), flexible and abundant security policies and policy-based network

management for various networks. It is greatly ideal for such applications as campus network, enterprise network,

government network, service network, residential broadband access and business building network, providing high-speed,

high-efficiency, secure and intelligent access solutions.

Table 1-1 RG-S2910-H

Model

10/100/1000 Base-T

Auto-sensing Ethernet Port

SFP+

Port

1000Base-X

SFP Port

Console

Port

USB

Port

Pluggable

Power

Slot

RG-S2910-24GT4SFP-UP-H

24 (All are PoE+ capable.

Ports 1-4 are HPoE capable)

RG-S2910-10GT2SFP-UP-H

10 (Ports 1-8 are HPoE

capable)

RG-S2910-24GT4XS-UP-H

24 (All are PoE+ capable.

Ports 1-4 are HPoE capable)

The SPF+ ports are downward compatible with 1000Base-X. The SFP ports only support 1000Base-X modules.

1000Base-T is compatible with 100Base-TX and 10Base-T in the downlink direction.

For RG-S2910-24GT4SFP-UP-H /RG-S2910-24GT4XS-UP-H, the HPoE ports support 60W power supply and

support IEEE 802.af/at PoE.

For RG-S2910-10GT2SFP-UP-H, the HPoE ports support 95W power supply and support IEEE 802.af/at PoE.

1.1 RG-S2910-24GT4SFP-UP-H

Technical Specifications

Model

RG-S2910-24GT4SFP-UP-H

CPU

Built-in CPU, single-core processor, 1GHz

Flash Memory

512M

SDRAM

DDRIII 512MB

Optical Module

For details, see Appendix B.

The supported module type may change at any time. Consult us for the latest information.

SFP Port

Supports 1000Base-X modules. Does not support 100Base-FX.

When the SFP ports are used as stack ports:

When used as stack ports, SFP ports of hardware versions V1.XX only support 10G DAC

copper cables (XG-SFP-CU1M, XG-SFP-CU3M and XG-SFP-CU5M); SFP ports of

hardware versions V2.XX support 10G DAC copper cables (XG-SFP-CU1M,

XG-SFP-CU3M and XG-SFP-CU5M), 2.5G DAC copper cables (GE-SFP-STACK1.6M),

and SFP transceiver modules.

Power Supply

AC input

Rated voltage range: 100V to 240V

Maximum voltage range: 90V to 264V

Frequency: 50/60 Hz

Rated current: 6.8A

HVDC input

Voltage range: 192V to 290V

Current range: 2.5A to 3.5A

EEE

Supported

PoE

All the RJ45 ports are PoE-capable. Ports 1-4 are HPoE-capable with the maximum power

output of 60W. Ports 5-24 support the maximum power output of 30W.

The maximum output power of PoE/PoE+/HPoE is 370W.

The HPoE ports support the maximum power supply of 60W only when connected with

HPoE PDs. For example, RG-PBOX-DC12 and RG-PBOX-AC24.

HPoE ports support IEEE 802.af/at PoE.

The available number of PDs is determined by PSE output power and PD input power in

practice.

Power

Consumption

Less than 40W with no PoE load

Less than 460W with PoE full load

Operating

Temperature

0℃to 50℃

Storage

Temperature

-40℃to 70℃

Operating Humidity

10% to 90%

Storage Humidity

5% to 95%

Fan

Speed adjustment and fault alarm

Temperature

Warning

Supported

EMCStandards

GB9254-2008

EN 300 386

EN 61000-3-2

EN 61000-3-3

EN 61000-4-2

EN 61000-4-3

EN 61000-4-4

EN 61000-4-5

EN 61000-4-6

EN 61000-4-11

EN 55022

EN 55024

EN 61000-4-8

Security Standards

GB4943-2011

EN60950-1

IEC60950-1

Dimensions

(W x D x H)

440 mm x 260 mm x 44 mm

Weight

≤5.5 kg (with package)

The RG-S2910-24GT4SFP-UP-H switch is a class A product. In a domestic environment, this product may cause

radio interference in which case the user may be required to take adequate measures.

Product Appearance

On the front panel, the RG-S2910-24GT4SFP-UP-H Ethernet switch provides 24 10/100/1000Base-T Ethernet ports, 4

SFP ports, and 1 Console port. On the back panel, it provides AC power ports.

Figure 1-1 Appearance of RG-S2910-24GT4SFP-UP-H

Front Panel

Figure 1-2 Front Panel of RG-S2910-24GT4SFP-UP-H

Note:

1. System status LED

2. PoE status LED

3. Copper port status LED

4. Fiber port status LED

5. PoE Mode Switch-Over Button

6. Console port

7. 10/100/1000Base-T auto-sensing Ethernet port

8. 1000Base-X SFP port

9. 1000Base-X SFP port

Long press PoE Mode Switch-Over Button for above 2 seconds to switch the display mode between PoE mode and

port rate mode.

Back Panel

Figure 1-3 Back Panel of RG-S2910-24GT4SFP-UP-H

Note:

1. Grounding pole

Power Supply

The RG-S2910-24GT4SFP-UP-H switch adopts AC or HVDC power input.

AC input

Rated voltage range: 100V to 240V

Maximum voltage range: 90V to 264V

Frequency range: 50/60 Hz

Rated current: 6.8A

Power cord specification: 10A

HVDC input

Voltage range: 192V to 290V

Current range: 2.5A to 3.5A

Heat Dissipation

The RG-S2910-24GT4SFP-UP-H adopts turbine fans for heat dissipation, thereby ensuring normal function of the device

in the specified environment. 10 cm distance space should be reserved at both sides and the back plane of the cabinet to

allow air circulation. It is recommended to clean the device once every 3 months to avoid dust from blocking vents. Figure

1-4 shows the flow scheme of heat dissipation.

Figure 1-4 Flow Scheme of Heat Dissipation

LEDs

LED

Panel Identification

State

Meaning

System status LED

Status

Off

The switch is not receiving power.

Blinking green

The system is being initialized.

Continuous blinking indicates errors.

Solid green

The switch is operational.

Solid yellow

Temperature warning

Check the working environment of the switch

immediately.

Solid red

The switch is faulty.

PoE status LED

PoE

Solid green

Indicates the switching state.

Solid yellow

Indicates the PoE state.

1-24

Off

The port is not connected.

1000Mbps RJ-45 port

status LED

Solid green

The port is connected at 1000 Mbps.

Blinking green

The port is receiving or transmitting traffic at 1000

Mbps.

Solid yellow

The port is connected at 10/100 Mbps.

Blinking yellow

The port is receiving or transmitting traffic at

10/100 Mbps.

RJ45 port PoE status

LED

1-24

Off

PoE is not enabled.

Solid green

PoE is enabled. The port is operational.

Solid yellow

The PoE port is abnormally operational.

1000Mbps SFP port

status LED

25F-28F

Off

The port is not connected.

Solid green

The port is connected at 1000 Mbps.

Blinking green

The port is receiving or transmitting traffic at 1000

Mbps.

1.2 RG-S2910-24GT4XS-UP-H

Technical Specifications

Model

RG-S2910-24GT4XS-UP-H

CPU

Built-in CPU, single-core processor, 1GHz

Flash Memory

512M

SDRAM

DDRIII 512MB

Optical Module

For details, see Appendix B.

The supported module type may change at any time. Consult us for the latest information.

SFP Port

Supports 10GBase-R and 1000Base-X modules.

When used as stack ports, SFP+ ports support 10G DAC copper cables (XG-SFP-CU1M,

XG-SFP-CU3M, and XG-SFP-CU5M) and SFP+ transceiver modules.

Power Supply

AC input

Rated voltage range: 100V to 240V

Maximum voltage range: 90V to 264V

Frequency: 50/60 Hz

Rated current: 6.8A

HVDC input

Voltage range: 192V to 290V

Current range: 2.5A to 3.5A

EEE

Supported

PoE

All the RJ45 ports are PoE-capable. Ports 1-4 are HPoE-capable with the maximum power

output of 60W. Ports 5-24 support the maximum power output of 30W.

The maximum output power of PoE/PoE+/HPoE is 370W.

The HPoE ports support the maximum power supply of 60W only when connected with

HPoE PDs. For example, RG-PBOX-DC12 and RG-PBOX-AC24.

HPoE ports support IEEE 802.af/at PoE.

The available number of PDs is determined by PSE output power and PD input power in

practice.

Power

Consumption

Less than 40W with no PoE load

Less than 460W with PoE full load

Operating

Temperature

0℃to 50℃

Storage

Temperature

-40℃to 70℃

Operating Humidity

10% to 90%

Storage Humidity

5% to 95%

Fan

Speed adjustment and fault alarm

Temperature

Warning

Supported

EMCStandards

GB9254-2008

Security Standards

GB4943-2011

Dimensions

(W x D x H)

440 mm x 260 mm x 44 mm

Weight

≤5.5 kg (with package)

The RG-S2910-24GT4XS-UP-H switch is a class A product. In a domestic environment, this product may cause

radio interference in which case the user may be required to take adequate measures.

Product Appearance

On the front panel, the RG-S2910-24GT4XS-UP-H Ethernet switch provides 24 10/100/1000Base-T Ethernet ports, 4

SFP+ ports, and 1 Console port. On the back panel, it provides AC power ports.

Figure 1-5 Appearance of RG-S2910-24GT4XS-UP-H

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ruijie Schalten Handbücher

Ruijie

Ruijie RG-S6150-X Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S7800C Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S2928G-E Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S2600G-I Series Bedienungsanleitung

Ruijie

Ruijie RG-S5750-H Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6510-48VS8CQ Installations- und Betriebsanleitung

Ruijie

Ruijie RG-ES05 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6150-X Series Anleitung zur Verwendung

Ruijie

Ruijie RG-N18000-XH Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6220-H Series Bedienungsanleitung

Ruijie

Ruijie RG-S5750-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SF2920 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-NBS3100 Series Anleitung zur Verwendung

Ruijie

Ruijie RG-S6510-48VS8CQ Installations- und Betriebsanleitung

Ruijie

Ruijie RG-ES109DS Bedienungsanleitung

Ruijie

Ruijie RG-CS83-PD Series Bedienungsanleitung

Ruijie

Ruijie RG-NBS3200 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6580-24DC8QC Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6930-2C Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6920-4C Series Installations- und Betriebsanleitung

Ruijie

Ruijie S8600E Series Handbuch

Ruijie

Ruijie Reyee RG-NIS Series Bedienungsanleitung

Ruijie

Ruijie RG-S6510-48VS8CQ Installations- und Betriebsanleitung

Ruijie

Ruijie RGOS 11.X Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch

Vimar

Vimar 6592 Montageanleitung