Ruijie RG-S6220-H Series Bedienungsanleitung

Confidentiality

Ruijie RG-S6220-H Series

Data Center Switches

Installation and Initialization

Controlled

•Hardware Installation

•Switch Management

•Software Upgrade

Hardware Installation

Preparations Installing the

Chassis to a

Specified Position Grounding Installing Power

Modules or

Extension

Modules Checking

Tip: Read the RG-S6220-H Series Switches Hardware Installation Manual if you install the switch for the first time.

Safety Notes

Do not install the switch in a wet place and keep it away from liquid.

Do not wear loose clothes during installation to avoid hooking components and causing damage. Therefore, fasten

clothes ribbons, scarves, and sleeves.

Place tools and components away from passageways to prevent collision.

Check for potential risks in the working area, for example, ungrounded power supplies, unreliable grounding of power

supplies, or wet floor.

Ambient Requirements

Temperature: 0C to 50C [AsRG-S6220-48XT6QXS-H generates more heats than the other models, its operating

temperature should in the range of 0C to 45C.]

Relative humidity: 10% to 90%

Cleanness: ≤ 3104(particle diameter ≥ 5 μm)

Ventilation: at least 20 cm clearance around the chassis for efficient heat dissipation

Anti-interference: far away from high-power (radar or radio transmitting station), high-frequency, or large-current

devices

Hardware Installation

Preparations Installing the

Chassis to a

Specified Position Grounding Installing Power

Modules or

Extension

Modules Checking

Tip: Read the RG-S6220-H Series Switches Hardware Installation Manual if you install the switch for the first time.

Make sure the following before the installation:

The installation position meets the ventilation requirement, with at least 20 cm clearance around the chassis.

The ambient temperature is in the range of 0C to 50C. [AsRG-S6220-48XT6QXS-H generates more heats than the

other models, its operating temperature should in the range of 0Cto 45C.] The relative humidity is in the range of

10% to 90%.

The external power supply system is ready and meets the following requirements:

Rated voltage range: 100-240 V AC, 50-60 Hz

Maximum voltage range: 90-264 V AC, 50-60 Hz

10 A standard power cable used

Network cables can be deployed properly at the installation site.

Hardware Installation

Preparations Installing the

Chassis to a

Specified Position Grounding Installing Power

Modules or

Extension

Modules Checking

Installing the Switch in a Standard 19-inch Cabinet Using Supports (Recommended)

The RG-S6220-H chassis is heavy (about 11 kg). Use either of the following methods to install the

chassis:

Method 1: Fix a tray on the cabinet and place the chassis on the tray.

Method 2: Install the chassis on the rear supports delivered with the switch.

Notes:

Fix the rack-mounting brackets and slide rails through the tapped holes on two ends of the side panels.

Install the rear support fastening screws and rack-mounting brackets on the front or rear side of the

chassis depending on which side the front panel is facing.

The rear supports delivered with the switch are only applicable to an 800-1200 mm deep cabinet.

Hardware Installation

Preparations

Installing the

Chassis to a

Specified

Position

Grounding

Installing Power

Modules or

Extension

Modules

Checking

Installing the Switch on a Desk (When Cabinet Mounting Cannot Be Implemented)

①Attach the four adhesive rubber pads delivered in the carton to the recessed areas at the four

corners of the chassis bottom.

②Place the switch on the desk. Ensure steadiness of the desk and leave sufficient clearance around

the switch for ventilation.

Caution: Do not place heavy objects on the switch.

Note: When the three fans in an RG-S6220-H switch fan run at full speed, they produce noise of 80 db

(complying with the noise standard for an unattended equipment room). The fan speed will be

automatically adjusted based on ambient temperature after startup of the switch. Installing the switch in

an office is not recommended. When the ambient temperature is around 25 oC, the noise is 50-55 db.

The fan rotates faster when the temperature is higher.

Hardware Installation

Preparations Installing the

Chassis to a

Specified Position Grounding Installing Power

Modules or

Extension

Modules Checking

There Is a Ground Bar in the Installation Environment

(Recommended)

①Remove the ground screw from the rear panel of

the chassis.

②Put the OT terminal of the ground cable delivered

with the switch on the ground screw of the chassis.

③Install the ground screw with the OT terminal to the

ground hole, fasten it with a screwdriver, and

connect the other end of the ground cable to the

ground bar of the equipment room. (Adjust the

length of the ground cable based on the distance

with the ground bar.)

There Is No Ground Bar in the Installation Environment

If the switch adopts AC power supply, the PE cable of

the AC power supply needs to be grounded. Check

whether the PE cable of the AC power supply is properly

grounded in the power distribution room or on the AC

transformer side.

1 Rear panel

2 OT terminal of the ground cable and

ground screw

3Grounding tag

4 Ground cable

5 Tapped hole for the filler panel fastening

screw (not for grounding)

Hardware Installation

Preparations Installing the

Chassis to a

Specified Position Grounding Installing Power

Modules or

Extension

Modules Checking

Installing Power Modules

①Wear an ESD wrist strap. Ensure that the strap is in good contact with your wrist and is reliably

grounded.

②Take out a power module from the package and verify that it is the required model.

③Determine in which slot to install the power module. Face the power module slot during the

operation.

④Hold the power module with the top side facing up. (Because of the structural design of the power

module slot and the power module, the power module will not be inserted into the slot when it is

upside down.) Hold the handle of the power module with one hand and support its bottom with the

other hand. Push the power module into the slot along the slide rails, as shown in the figure. When

you hear a click, the power module is securely seated in the slot.

Note: Power modules are hot swappable. The switch can

operate normally with a single power module.

Hardware Installation

Preparations Installing the

Chassis to a

Specified Position Grounding Installing Power

Modules or

Extension

Modules Checking

Installing Fan Modules

①Wear an ESD wrist strap. Ensure that the strap is in good contact with your wrist and is reliably

grounded.

②Take out a fan module from the package and verify that it is the required model.

③Determine in which slot (numbered 1, 2, or 3) to install the fan module. Face the fan slot during the

operation.

④Hold the fan module with the top side facing up. (Because of the structural design of the fan slot and

the fan module, the fan module will not be inserted into the slot when it is upside down.) Hold the

handle of the fan module with one hand and support its bottom with the other hand. Push the fan

module into the slot alone the slide rails, as shown in the figure. When you hear a click, the fan

module is securely seated in the slot.

⑤Tighten the captive screw on the fan module to fix the fan module in the

chassis.

Note: Fan modules work in 2+1 redundancy mode. A switch must have

at least two fan modules installed to ensure that it can start normally.

Hardware Installation

Preparations Installing the

Chassis to a

Specified Position Grounding Installing Power

Modules or

Extension

Modules Checking

Checking the Cabinet

Ensure that the external power supply system matches the power distribution panel of the cabinet.

Ensure that the front and rear doors of the cabinet can be closed with the switch in the cabinet.

Ensure that the cabinet is securely fixed and will not move or fall down.

Ensure that the switch is securely fixed in the cabinet and that all cables are bundled on the

cabinet.

Ensure that sufficient space is reserved around the switch for heat dissipation, especially at the

front and rear of the switch (at least 20 cm).

Checking Cable Connections

Ensure that optical fibers and twisted pair cables match the connected interfaces.

Ensure that all cables are bundled properly.

Ensure that ground cable specifications and connection are correct.

Check whether all the cables are routed indoors. If any cables are routed outdoors, check whether

AC power supply surge protection bars and network interface surge protectors are used.

Checking the Power Supply System

Ensure that all power cables are properly connected and meet security requirements.

Inhaltsverzeichnis

Andere Ruijie Schalten Handbücher

Ruijie

Ruijie RG-S5000-E Series Anleitung zur Verwendung

Ruijie

Ruijie RG-S6250-48XS8CQ Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-NBS5100-24GT4SFP-P Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S2600E Series Bedienungsanleitung

Ruijie

Ruijie RG-S6510-48VS8CQ Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S5760C-X Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S2900 Series Bedienungsanleitung

Ruijie

Ruijie RG-ES05 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-NBS5200 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-S6150-X Series Anleitung zur Verwendung

Ruijie

Ruijie Reyee RG-ES106D-P V2 Bedienungsanleitung

Ruijie

Ruijie RG-CS86-20XS Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-ES Series Bedienungsanleitung

Ruijie

Ruijie RG-S6120 Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-ES126S-LP V2 Bedienungsanleitung

Ruijie

Ruijie RG-S5310-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie XS-S1960-48GT4SFP-H Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-IF2920U-12GT1XS Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-ES05 Series Bedienungsanleitung

Ruijie

Ruijie RG-S5300-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-NIS Series Bedienungsanleitung

Ruijie

Ruijie RG-S6580-48CQ8QC Installations- und Betriebsanleitung

Ruijie

Ruijie 5310-E Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-ES1 Series Installations- und Betriebsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch

Vimar

Vimar 6592 Montageanleitung