Ruijie Reyee RG-RAP2260 Installations- und Betriebsanleitung

Ruijie Reyee RG-RAP2260(E) Access Point

Hardware Installation and Reference Guide

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,

modification, transmission, translation or commercial use of this document or any portion of this document,

in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.

Exemption statement

This document is provided “as is”. The contents of this document are subject to change without any notice.

Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to

ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to

content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual will guide you through the installation of the access point.

Scope

It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it

is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

Ruijie Networks Website: https://www.ruijienetworks.com/

Technical Support Website: https://ruijienetworks.com/support

Case Portal: https://caseportal.ruijienetworks.com

Community: https://community.ruijienetworks.com

Technical Support Email: service_rj@ruijienetworks.com

Skype: service_rj@ruijienetworks.com

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that supported by the

product, with configuration examples.

Command Reference

Describes the related configuration commands, including command modes,

parameter descriptions, usage guides, and related examples.

Documentation Conventions

The symbols used in this document are described as below:

This symbol brings your attention to some helpful suggestions and references.

This symbol means that you must be extremely careful not to do some things that may damage the device or cause

data loss.

Hardware Installation and Reference Guide Product Overview

1 Product Overview

Featuring leading 802.11a/b/g/n/ac/ax and MU-MIMO, Ruijie RG-RAP2260(E) supports 4 spatial streams and delivers up

to 800Mbps at 2.4G and 2400Mbps at 5G. The overall dual-band performance speeds up to 3200Mbps per device, totally

eliminating Gigabit wireless bottlenecks. RG-RAP2260(E) adopts either local power supply or PoE power supply, and

provides two Ethernet ports, making it possible connect a camera or switch device to adapt to challenges in a wide variety

of deployment scenarios.

1.1 Technical Specifications

Table 1-1 RG-RAP2260(E) Technical Specifications

Model

RG-RAP2260(E)

Four-stream and dual-band

Transmission

Protocol

Support concurrent 802.11ax, 802.11ac wave2/wave1, 802.11a/b/g/n

Operating Bands

802.11b/g/n: 2.4 GHz to 2.4835 GHz

802.11a/n/ac/ax: 5.150 GHz to 5.250 GHz, 5.250 GHz to 5.350 GHz, 5.470 GHz to 5.725 GHz,

5.725 GHz to 5.850 GHz (Country-specific)

Antenna

Array antenna (2.4G: 3dBi, 5G: 3dBi)

Spatial Streams

2.4G: 4 x 4 MIMO

5G: 4 x 4 MIMO

Max Throughput

2.4G: up to 800 Mbps

5G: up to 2400 Mbps

Up to 3200 Mbps per AP

Modulation

OFDM: BPSK@6/9Mbps, QPSK@12/18Mbps, 16QAM@24Mbps, 64QAM@48/54Mbps

DSSS: DBPSK@1Mbps, DQPSK@2Mbps, and CCK@5.5/11Mbps

MIMO-OFDM: BPSK, QPSK, 16QAM , 64QAM, 256QAM and1024QAM

OFDMA

Receive Sensitivity

11b: -91dBm(1Mbps), -90dBm(5Mbps), -87dBm(11Mbps)

11a/g: -89dBm(6Mbps), -82dBm(24Mbps), -78dBm(36Mbps), -72dBm(54Mbps) 11n:

-85dBm(MCS0), -67dBm(MCS7)

11ac: 20MHz: -85dBm(MCS0), -60dBm(MCS9)

11ac: 40MHz: -82dBm(MCS0), -57dBm(MCS9)

11ac: 80MHz: -79dBm(MCS0), -53dBm(MCS9)

11ax: 80MHz: -79dBm(MCS0), -53dBm(MCS9),-52dBm(MCS11)

Transmit Power

≤100mw(20dBm) (adjustable)

Transmit Power

Adjustment

1 dBm

Dimensions

(W x D x H)

220 mm x 220 mm x 35 mm (8.7 in. x 8.7 in. x 1.4 in.) (excluding brackets)

Weight

≤1.05 kg (excluding brackets)

Service Ports

One 10/100/1000BASE-T Ethernet uplink port, one 10/100/2500BASE-T Ethernet uplink port,

Hardware Installation and Reference Guide Product Overview

LAN1/2.5G/PoE port is PoE+-capable

Management Ports

N/A

LED

1 LED (green)

Power Supply

Adapter: DC 12 V/2.5 A (optional)

PoE: IEEE 802.3at-compliant (PoE+).

Power Consumption

< 25.4W

Temperature

Operating: 0°C to 40°C (32°F to 104°F)

Storage: –40°C to 70°C (–40°F to 158°F)

Humidity

Operating: 5% to 95% RH (non-condensing)

Storage: 5% to 95% RH (non-condensing)

Installation

Ceiling/wall mount

Safety Standards

GB4943

IEC60950-1

EMC Standards

GB9254

EN301 489

EN50155

EN50121

Mechanical

Vibration

IEC61373

Radio

China Radio Transmission Equipment Type Approval Certificate

EN300 328

EN301 893

MTBF

> 400,000 H

Weight refers to the weight of host.

1.2 Product Image

The AP provides two Ethernet ports (LAN1/2.5G/PoE port is PoE+-capable), and one power port for an external power

supply.

Figure 1-1 Appearance of RG-RAP2260(E)

Hardware Installation and Reference Guide Product Overview

1.3 LED Indicator and Button

LED Indicator

and Button

State

Frequency

Meaning

LED Indicator

Off

N/A

The AP is NOT receiving power.

Blinking

0.5Hz

Normal operation, but there is an alarm.

Fast blinking

10Hz

Possible cases:

1. Restoring the factory default settings

2. Upgrading the firmware

3. Restoring the image file

4. Initializing the device

Solid green

N/A

Normal operation.

Reset Button

Press for less than 2 seconds

Restart the device.

Press for more than 5 seconds

Restore the factory settings.

1.4 Power Sources

The AP can be powered either with a power adapter or through Power over Ethernet (PoE).

The power adapter is customer-supplied.

To use a PoE device, make sure that it supports the IEEE 802.3at standard.

1.5 Cooling Solution

The AP features a fanless design.

Leave sufficient space surrounding the AP when installing the AP to permit proper airflow for ventilation.

Hardware Installation and Reference Guide Preparing for Installation

2 Preparing for Installation

To prevent device damage and physical injury, please read the safety recommendations carefully as described in this

chapter.

Recommendations do not cover all possible hazardous situations.

2.1 Installation

The AP must be installed indoors. To ensure normal operation, the installation site must meet the following requirements.

Install the AP in a well-ventilated environment. If it is installed in a closed room, make sure there is a good cooling

system.

Make sure the site is sturdy enough to support the AP and its accessories.

Make sure the site has enough space for installing the AP and leave sufficient room around the AP for ventilation.

Do not expose the AP to high temperature, dust, or harmful gases.

Do not install the AP in an area prone to fire or explosions.

Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.

Do not subject the AP to unstable voltage, vibration, and noises.

Keep the AP at least 500 meters away from the ocean and do not face it towards the sea breeze.

The installation site should be free from water including possible flooding, seepage, dripping, or condensation.

The installation site should be selected according to network planning and communications equipment features, and

considerations such as climate, hydrology, geology, earthquake, electrical power, and transportation.

Please follow the correct method described in the installation guide to install and remove the device.

2.2 Movement

Avoid frequently moving the device.

Turn off all power supplies and unplug all power cables before you remove the device.

2.3 EMI

Please observe local regulations and specifications when performing electrical operations. Relevant operators must

be qualified.

Carefully check for any potential hazards in the working area such as damp/wet ground or floors.

Find the location of the emergency power supply switch in the room before installation. Cut off the power supply first

in case of an accident.

Be sure to make a careful check before shutting down the power supply.

Hardware Installation and Reference Guide Preparing for Installation

Do not place the device in a damp/wet location. Do not let any liquid enter the chassis.

Keep the AP far away from grounding or lightning protection devices for power equipment.

Keep the AP away from radio stations, radar stations, high-frequency high-current devices, and microwave ovens.

Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electric shock, thus

causing severe even fatal damages to humans and devices.

Direct or indirect contact with a wet object (or your finger) on the high voltage and power line can be fatal.

2.4 Ventilation

For proper ventilation, leave sufficient space around the AP.

2.5 Temperature and Humidity

To ensure the normal operation and equipment service life, maintain appropriate temperature and humidity levels in the

equipment room. See Table 2-1. Improper room temperature and humidity can cause damage to the device.

High relative humidity may affect insulation materials, resulting in poor insulation and even electrical leakage.

Sometimes it may lead to changes in the mechanical properties of materials and corrosion of metal parts.

Low relative humidity can dry and shrink insulation sheets and cause static electricity that can damage the circuitry.

High temperatures greatly reduce device reliability and shorten service life.

Table 2-1 Required Temperature and Humidity for the RG-RAP2260(E)

Temperature

Relative Humidity

0ºC to 40ºC (32°F to 104°F)

5% to 95%

2.6 Cleanness

Dust poses a serious threat to device operation. Dust on the surface of the device can be absorbed onto metal contact

points by static electricity causing poor contact. Electrostatic absorption of dust occurs more easily when the relative

humidity is low, and might shorten the equipment service life and cause communication failures. Table 2-2 shows the

maximum concentration and diameter of dust allowed in the equipment room.

Table 2-2

Maximum diameter (μm)

0.5

Maximum concentration

(Particles/m3)

1.4×107

7×105

2.4×105

1.3×105

The amount of salt, acids and sulfides in the air are also strictly limited for the equipment room. These substances can

accelerate metal corrosion and aging of some parts. Table 2-3 describes the limits of some hazardous gases such as SO2,

H2S, NO2and Cl2 in the equipment room.

Table 2-3

Gas

Average (mg/m3)

Maximum (mg/m3)

Hardware Installation and Reference Guide Preparing for Installation

SO2

0.2

1.5

H2S

0.006

0.03

NO2

0.04

0.15

NH3

0.05

0.15

Cl2

0.01

0.3

2.7 Power Supply

DC power adapter:

Input voltage: 12V

Rated current: 2.5A

PoE+ injector: IEEE 802.3at compliant

Technical Specifications of the DC Connector

Inner Diameter

Outer Diameter

Insertion

Depth

Conductor

Impedance

Voltage-endu

rance

Impedance

Voltage-endu

rance

(Insulator and

Conductor)

Polarity

2.10+/-0.05mm

5.50+/-0.05mm

9mm

5Ω

100MΩ

1000V

Inner pole:

positive

Outer pole:

negative

The DC input power should be greater than the power actually consumed by the system.

Use DC power adapters with specifications recommended by Ruijie.

Please use Ruijie certified PoE injectors.

Warning：802.3af or non-standard POE adapter may cause unknown issues. Please use Ruijie POE+ switch or

802.3at POE adapter as power supplier

2.8 Installation Tools

Common Tools

Phillips (crosshead) screwdriver, copper and fiber cables, bolts, diagonal pliers, cable ties

Special Tools

Wire stripper, crimping pliers, RJ-45 crimping pliers, punch down tool

Meter

Multimeter, bit error rate tester (BERT)

The tools listed above are customer supplied.

2.9 Unpacking the Access Point

Package Contents

Hardware Installation and Reference Guide Preparing for Installation

Items

Verify that all parts are installed and debugged.

Screws

Mounting brackets

Product quick installation guide

Packing list

The above listed items are for general situations, and contents mayvary in the actual shipment. The purchasing order

shall prevail in any case. Please check each item carefully according to the packing list or purchasing order. If any

item is damaged ormissing, notify your sales representative.

Andere Handbücher für Reyee RG-RAP2260

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ruijie Drahtloser Zugangspunkt Handbücher

Ruijie

Ruijie RG-WLAN Series Bedienungsanleitung

Ruijie

Ruijie RG-AP840-L Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP680-AR Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP880-L Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RAP6260-D Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP630 IDA2 Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2200 Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee Series Abmessungen

Ruijie

Ruijie RG-SAP685-SP Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2200 Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP130(W2) V2 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP180(V3) Installations- und Betriebsanleitung

Ruijie

Ruijie RG-MAP852-SF-M Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP680-I Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP850-I-V2 Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2260 Installations- und Betriebsanleitung

Ruijie

Ruijie RG-MAP852-SF-S Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP680-CD Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP810-L Installations- und Betriebsanleitung

Ruijie

Ruijie RG-WLAN Series Bedienungsanleitung

Ruijie

Ruijie RG-SAP750-SP Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP180 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP150-SP-W Installations- und Betriebsanleitung

Ruijie

Ruijie RG-WLAN Series Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung