Ruijie RG-AP630 IDA2 Series Installations- und Betriebsanleitung

Ruijie RG-AP630(IDA2) Series Access Points

Hardware Installation and Reference Guide V1.6

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,

transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,

without the prior written consent of Ruijie Networks is prohibited.

Exemption statement

This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain

the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will

not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual will guide you through the installation of the access point.

Scope

It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it

is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

Ruijie Networks Website: https://www.ruijienetworks.com/

Technical Support Website: https://ruijienetworks.com/support

Case Portal: https://caseportal.ruijienetworks.com

Community: https://community.ruijienetworks.com

Technical Support Email: [email protected]

Skype: [email protected]

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that supported by the

product, with configuration examples.

Command Reference

Describes the related configuration commands, including command modes,

parameter descriptions, usage guides, and related examples.

Documentation Conventions

The symbols used in this document are described as below:

This symbol brings your attention to some helpful suggestions and references.

This symbol means that you must be extremely careful not to do some things that may damage the device or cause

data loss.

Hardware Installation and Reference Guide Product Overview

1Product Overview

The RG-AP630(IDA2) is a wireless access point (AP) designed by Ruijie for next-generation high-speed wireless LANs.

Adhering to the latest 802.11ac Wave2 standard, the AP delivers an access rate of up to 1733Mbps+800Mbps. It features

security, radio frequency (RF) control, mobile access, Quality of Service (QoS), and seamless roaming. In addition, it can

be managed by RG-WS series wireless access controllers (ACs) to implement wireless data forwarding, security, and

access control.

The IP68 design adapts to inclement outdoor environments such as the cold and humidity. This substantially simplifies

installation and maintenance. The RG-AP630(IDA2) offers flexible antenna switching and full coverage for various outdoor

situations. Moreover, multi-hop and point-to-multi-points bridging enhances the deployment. The AP fed by IEEE

802.3at-compliant PoE accommodates various monitors and receives real-time monitoring information. It is perfectly

suited for such sites as campuses, city blocks, and plazas.

1.1 Technical Specifications

Table 1-1 RG-AP630(IDA2) Technical Specifications

Model

RG-AP630(IDA2)

Dimensions

(L×W×H)

276 mm × 246 mm × 90 mm (10.87 in. x 9.69 in. x 3.54 in.)

Maximum Transmit

Rate

Internal antenna: 2.533Gbps(1733Mbps@5GHz ;[email protected])

External antenna: 1.9Gbps(1300Mbps@5GHz ;[email protected])

Operating

Frequency

802.11b/g/n: 2.4GHz to 2.483GHz

802.11a/n/ac: 5.150 GHz to 5.350GHz, 5.47GHz to 5.725GHz, 5.725 GHz to 5.850GHz

(Country-Specific)

Maximum Transmit

Power

27dBm

Antenna Type

Built-in directional antenna

Antenna Gain

2.4GHz: 10dBi

5GHz: 10dBi

Lobe Width

2.4G: E:30°: H:60°

5G: E:30°: H:60°

Interfaces

One 10/100/1000 Base-T uplink Ethernet port

One SFP uplink port (combo)

One 10/100/1000 Base-T downlink PoE port

Fat/Fit Mode

Switching

Supported

LED

One system status LED

Three WDS RSSI LEDs

PoE

IEEE 802.3at (PoE+)

Power Consumption

<25w

Temperature

Operating: -40°C to 65°C (-40°F to 149°F)

Storage: -40°C to 85°C (-40°F to 185°F)

Hardware Installation and Reference Guide Product Overview

Humidity

Operating: 0% to 100% (non-condensing)

Storage: 0% to 100% (non-condensing)

IP Rating

IP68

Weight

<2.5 kg (5.51 lbs)

Safety Standards

GB4943, EN60601-1-2 (medical care), UL/CSA 60950-1, EN/IEC 60950-1, EN/IEC 60950-22

EMC Standards

GB9254-2008, EN301 489, EN55022, FCC Part15, RSS-210

Table 1-2 LEDs of RG-AP630(IDA2)

LED

State

Meaning

Blinking green

The system is booting.

Solid green

Initialization in progress or proper operation.

Blinking yellow

Initialization is complete, but no CAPWAP connection.

System status

Solid red

The LAN port is disconnected.

1 solid on

< -70dBm

2 solid on

-70 to -50dBm

WDS RSSI (3

LEDs in total)

3 solid on

> -50dBm

1.2 Product Appearance

The AP provides 1 ETH1/PoE IN port (RJ45), 1 ETH2 port (RJ45), 1 SFP combo port, 1 Console port, and 6 N-type

antenna connectors.

Figure 1-1 Product Appearance of the RG-AP630(IDA2)

Hardware Installation and Reference Guide Product Overview

1.3 Front View

Figure 1-2 RG-AP630(IDA2) Front View

Note:

1. 2.4GHz&5GHz antenna connector

3.10/100/1000 Base-T auto-sensing Ethernet port

5. SFP combo port

2. Console port

4.10/100/1000 Base-T auto-sensing

Ethernet/PoE IN port

6. 2.4GHz & 5GHz antenna connector

1.4 Power Supply

The AP supports 802.3at PoE+ power supply.

1.5 Package Contents

Table 1-3 RG-AP630(IDA2) Package Contents

Name

Quantity

Unit

Remarks

Host

Set

Mounting plate

Piece

Mounting bracket

Piece

Tie rod

Piece

M8x20 screw with spring and flat washers

Piece

M8X40 screw with spring and flat washers

Piece

Liquid-tight adapter

Piece

Seal plug

Piece

Preinstalled

Protective cap for Type-N RF connector

Piece

Preinstalled

Grounding cable

Piece

Hose clamp

Piece

M8X60 anchor

Piece

Product Warranty Manual

Copy

RG-AP630(IDA2) Series Access Point

Hardware Installation and Reference Guide

Copy

Hardware Installation and Reference Guide Product Overview

Ruijie Networks Wireless Device

Management Software

Piece

Preinstalled

Hardware Installation and Reference Guide Preparing for Installation

2Preparing for Installation

To prevent device damage and physical injury, please read carefully the safety recommendations described in this

chapter.

Recommendations do not cover all possible hazardous situations.

2.1 Grounding and Lightning Protection

Keep the grounding connection within 30 m, and use a 40mm x 4mm or 50mm x 5mm ground bar of hot-dip

zinc-coated flat steel sheet.

When the connection cable between the main grounding conductor and local equipotential earthing terminal board

(LEB) on each floor is shorter than 2 meters, use a stranded copper wire with a sectional area not less than 1.318

mm2 (16 AWG) for the connection cable.

Use a shielded network cable if possible, ensure that devices connected to both ends of the shielded network cable

are reliably grounded, and make sure that the sheath of the shielded network cable is also grounded if possible. If no

shielded network cable is available, wire the network cable through a steel pipe and bury the steel pipe for lead-in,

and properly ground both ends of the steel pipe.

No additional lightning protector is required as a high-profile lightning protector is built in the AP630(IDA2) and the

antenna port and power port support 6kV lightning protection. If a lightning protector of a higher profile is available,

configure the lightning protector optionally. Before the configuration, connect the lightning protector to the ground

cable.

Use a power cable with the PE end to ground the power supply (AC). Ensure that the PE end is properly grounded,

with a ground resistance less than 5 ohms. Do not use a two-wire power cable with only the live (L) wire and naught

(N) wire. Do not connect the N wire to the protection ground cable of other communication devices, and ensure that

the L wire and N wire are properly connected.

Ensure that the ground resistance is less than 5 ohms. In areas with high soil resistivity, reduce the soil resistivity via

measures such as spreading resistivity reduction mixture around the grounding conductor.

2.2 Preparing the Installation Site

Do not expose the AP to high temperature, dust, or harmful gases.

Do not install the AP in an area prone to fire or explosions.

Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.

Do not subject the AP to unstable voltage, vibration, and noises.

Keep the AP at least 500 meters away from the ocean and do not face it towards the sea breeze.

The installation site should be protected from water and flooding, seepage, dripping, or condensation.

The installation site should be selected according to network planning, communications equipment features and

considerations such as climate, hydrology, geology, earthquake, electric power, and transportation.

Hardware Installation and Reference Guide Preparing for Installation

2.2.1 Temperature and Humidity

Table 2-1 Required Temperature and Humidity for the RG-AP630(IDA2) Series

Operating Temperature

-40°C to 65°C (-40°F to 149°F)

Operating Humidity

0% to 100% (non-condensing)

2.2.2 Outdoor Installation

The AP can be installed outdoors and mounted on a wall or pole.

2.2.3 Waterproof

Use a seal plug to seal the unused ports.

Figure 2-1 Seal Plug

Use a watertight adapter to connect cables to the AP. For details, see Chapter 3 “Installing the Access Point”.

Figure 2-2 Watertight Adapter

2.2.4 EMI

All interference sources (from outside or inside of the device or application system) affect the device by capacitive

coupling, inductive coupling, or electromagnetic waves.

Electromagnetic interference (EMI) occurs due to electromagnetic radiation or conduction, depending on the transmission

path.

Hardware Installation and Reference Guide Preparing for Installation

Radiation interference occurs when energy (usually radio frequency energy) is emitted from a device and propagated

through space to disrupt other devices. The interference source can be part of disrupted system or a fully electrically

isolated unit. Conduction interference occurs when interference is transferred from one unit to another through cables,

which are usually electromagnetic wires or signal cables connected between the source and the device(s) experiencing

interference. Conduction interference often affects the power supply of the device. It is eliminated by using filters.

Radiation interference can influence the path of any signal from the device and is difficult to shield.

Take effective measures against interference from the power grid.

Keep the AP far away from the grounding or lightning protection devices for power equipment.

Keep the AP away from high-power radio stations, radar stations, and high-frequency high-current devices.

Take electrostatic shielding measures.

2.3 Fiber Connection

Before connecting fiber cables, make sure the model of the optical transceiver and fiber type match the optical port. The

transmit port on the local device should be connected to the receive port on the peer device and vice versa.

2.4 Installation Tools

Table 2-2 Installation Tools

Tools

Marker, Phillips (crosshead) screwdriver, slotted screwdriver, drill, paper knife, crimping pliers,

diagonal pliers, wire stripper, network cable tester, related power and fiber cables, wrench,

hammer, cable ties, ESD tools, multimeter

The tool kit and cables are customer supplied.

2.5 Checking before Installation

Please check your materials carefully against the package contents. If there are any errors, please contact your distributor.

Inhaltsverzeichnis

Andere Ruijie Drahtloser Zugangspunkt Handbücher

Ruijie

Ruijie RG-AP180-I Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP850-I-V2 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-WLAN Series Bedienungsanleitung

Ruijie

Ruijie RG-AP820-L(V2) Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP810-I Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP630 Directional Bedienungsanleitung

Ruijie

Ruijie Reyee Series Bedienungsanleitung

Ruijie

Ruijie RG-AP680-A Installations- und Betriebsanleitung

Ruijie

Ruijie RG-MAP852-SF-S Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP840-I Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP52-OD Bedienungsanleitung

Ruijie

Ruijie RG-AM5532 Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP73HD Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP720-L Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP820-I Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP840-I (V2) Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP885-SP Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP Series Bedienungsanleitung

Ruijie

Ruijie RG-AP820(AR) Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP1200-MNT Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP110-L Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP1260 Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP880-AR Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP73HD Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung