Ruijie RG-AP820-L(V2) Series Installations- und Betriebsanleitung

Ruijie RG-AP820-L(V2) Series Access Points

Hardware Installation and Reference Guide V1.00

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,

modification, transmission, translation or commercial use of this document or any portion of this document,

in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.

Exemption statement

This document is provided “as is”. The contents of this document are subject to change without any notice.

Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to

ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to

content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual will guide you through the installation of the access point.

Scope

It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it

is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

Ruijie Networks Website: https://www.ruijienetworks.com/

Technical Support Website: https://ruijienetworks.com/support

Case Portal: https://caseportal.ruijienetworks.com

Community: https://community.ruijienetworks.com

Technical Support Email: [email protected]

Skype: [email protected]

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that supported by the

product, with configuration examples.

Command Reference

Describes the related configuration commands, including command modes,

parameter descriptions, usage guides, and related examples.

Documentation Conventions

The symbols used in this document are described as below:

This symbol brings your attention to some helpful suggestions and references.

This symbol means that you must be extremely careful not to do some things that may damage the device or cause

data loss.

1 Product Overview

Featuring leading 802.11ax, Ruijie RG-AP820-L(V2) delivers up to 57[email protected] and 1.2Gbps@5G. The overall

dual-radio, dual-band performance speeds up to 1.775Gbps per device, totally eliminating Gigabit wireless bottlenecks.

1.1 Technical Specifications

Table 1-1 Technical Specifications of RG-AP820-L(V2)

Hardware Specifications

Radio

2.4GHz: 2 x 2 MU-MIMO

5GHz: 2 x 2 MU-MIMO

Transmission

Protocol

Support concurrent 802.11ax and 802.11a/b/g/n/ac.

Operating Bands

2400MHz to 2483.5MHz (b/g/n/ac, HE40)

5725MHz to 5850MHz (a/n/ac, HE80)

5470MHz to 5725MHz (a/n/ac, HE80)

5150MHz to 5350MHz (a/n/ac/ax, HE80)

(Depending on which country the AP is installed)

Antenna

Built-in antenna

Spatial Streams

2.4G: 2 streams

5G: 2 streams

Access Rates

2.4GHz: up to 575Mbp

5GHz: up to 1.2Gbps

2.4GHz+5GHz: up to 1.775Gbps

Total: up to 2.4Gbps

Modulation

OFDM: BPSK@6/9Mbps, QPSK@12/18Mbps, 16-QAM@24Mbps, 64-QAM@48/54Mbps

DSSS: DBPSK@1Mbps, DQPSK@2Mbps, and [email protected]/11Mbps

MIMO-OFDM: BPSK, QPSK, 16QAM, 64QAM, 256QAM and1024QAM

OFDMA

Receive Sensitivity

11b: -96dBm(1Mbps), -93dBm(5Mbps), -89dBm(11Mbps)

11a/g: -91dBm(6Mbps), -85dBm(24Mbps), -80dBm(36Mbps), -74dBm(54Mbps)

11n: -90dBm@MCS0, -70dBm@MCS7, -89dBm@MCS8, -68dBm@MCS15

11ac: HT20: -88dBm(MCS0), -63dBm(MCS9)

11ac: HT40: -85dBm(MCS0), -60dBm(MCS9)

11ac: HT80: -82dBm(MCS0), -57dBm(MCS9)

11ax: HE80: -82dBm(MCS0), -57dBm(MCS9),-52dBm(MCS11)

Maximum Transmit

Power

≤100mw (20 dBm)

(Depending on the country of use, laws and regulations.)

Transmit Power

Adjustment

1 dBm

Physical

Dimensions

(W x D x H)

193 mm x153 mm x 26 mm

(7.60 in x 6.02 in x 1.02 in)

Weight

≤1 kg (2.20 lbs)

Service Ports

One 10/100/1000BASE-T Ethernet port (802.3af PoE-capable)

Management Ports

One RJ45 Console port supports 9600bps, 57600bps and 115200bps.

Button

One Reset button

Anti-Theft Lock

Support

LED

1 LED (red, green, blue, orange, and flashing modes, flashing mode for smart device access,

and the indicator can be switched off to silent mode)

Power Supply

Adapter: DC 48V/0.3A (optional)

PoE: IEEE 802.3af

Power Consumption

Maximum: 12.95W

Bluetooth

Bluetooth 5.0 (BLE)

Temperature

Operating: -10°C to 50°C (14°F to 122°F)

Storage: -40°C to 70°C (-40°F to 158°F)

Humidity

Operating: 5% to 95% RH (non-condensing)

Storage: 5% to 95% RH (non-condensing)

Installation

Ceiling/wall mount

IP Rating

IP41

Safety Standards

GB4943-2011

IEC60950-1

IEC60825-1

EMC Standards

EN300386

GB19286-2003

GB17618-1998

Vibration Standards

NEBS GR-63-CORE_Issue3_2006

Radio

China Radio Transmission Equipment Type Approval Certificate

EN300 328

EN301 893

MTBF

> 200,000H

The weight refers to the weight of host and bracket.

1.2 Product Image

The AP provides one Ethernet ports (PoE-capable), one Console port, and one power port for external power supply.

Figure 1-1 Appearance of RG-AP820-L(V2)

Note

1. Reset button

2. LED indicator

3. Anti-Theft lock hole

4. RJ45 Console port

5. LAN/PoE port

6. 48V DC power port

1.3 LED Indicators

Fit AP

State

Frequency

Meaning

Off

N/A

The AP is NOT receiving power. Or the AP is in Do Not Disturb mode, which

can be disabled by software.

Blinking green

3Hz

uBoot program initialization in progress

Solid green

N/A

Main program initialization in progress

Blinking red

3Hz

Initialization is complete, but no Ethernet activity.

2Hz

Locates the AP.

Solid orange

N/A

Initialization is complete, and the AP is establishing a CAPWAP connection

with an AC.

Blinking orange

3Hz

Firmware upgrade in progress. Do not power off.

Solid blue

N/A

Normal operation, but no wireless clients are associated with the AP.

Blinking blue

3Hz

Normal operation, at least one wireless client is associated with the AP.

Reset button

Pressed for less

than 2s

Reboots the device.

Pressed for more

than 3s

Restores default settings.

Fat AP

State

Frequency

Meaning

Off

N/A

The AP is NOT receiving power. Or the AP is in Do Not Disturb mode, which

can be disabled by software.

Blinking green

3Hz

uBoot program initialization in progress

Solid green

N/A

Main program initialization in progress

Blinking red

3Hz

Initialization is complete, but no Ethernet activity.

Solid blue

N/A

Normal operation, but no wireless clients are associated with the AP.

Blinking blue

3Hz

Normal operation, at least one wireless client is associated with the AP.

Reset button

Pressed for less

than 2s

Reboots the device.

Pressed for more

than 3s

Restores default settings.

1.4 Power Sources

The AP can be powered either with a DC power adapter or through Power over Ethernet (PoE).

The AP requires Ruijie power adapters (If needed, you can buy them from Ruijie).

To use a PoE device, make sure it supports the IEEE 802.3af PoE standard.

1.5 Cooling Solution

The AP adopts fanless design.

Leave sufficient space at the surrounding of the AP when place the AP to permit airflow for proper ventilation.

2 Preparing for Installation

To prevent device damage and bodily injury, please read carefully the safety recommendations described in this

chapter.

The recommendations do not cover all possible hazardous situations.

2.1 Installation

The AP must be installed indoors. To ensure its normal operation, the installation site must meet the following

requirements.

Install the AP in a well-ventilated environment. If it is installed in a closed room, make sure there is a good cooling

system.

Make sure the site is sturdy enough to support the AP and its accessories.

Make sure the site has enough space for installing the AP and leave sufficient room around the AP for ventilation.

Also, to avoid mutual interference, ensure the site is at least 2 meters away from a base station antenna.

Do not expose the AP to high temperature, dusts, or harmful gases.

Do not install the AP in an inflammable or explosive environment.

Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.

Do not subject the AP to unstable voltage, vibration, and noises.

Keep the AP at least 500 meters away from the seaside and do not face it toward the wind from the sea.

The installation site should be free from water flooding, seepage, dripping, or condensation.

The installation site shall be selected according to network planning and features of communications equipment, and

considerations such as climate, hydrology, geology, earthquake, electric power, and transportation.

Please follow the correct method described in the installation guide to install and remove the device.

2.2 Movement

Avoid moving the device frequently.

Turn off all power supplies and unplug all power cables before you remove the device.

2.3 EMI

Please observe local regulations and specifications when performing electrical operations. Relevant operators must

be qualified.

Please carefully check for any potential danger in the working area, for example, damp/wet ground or floor.

Find out the location of the emergency power supply switch in the room before installation. First cut off the power

supply in case of an accident.

Be sure to make a careful check before you shut down the power supply.

Do not place the device in a damp/wet location. Do not let any liquid enter the chassis

Keep the AP far away from the grounding or lightning protection devices of power equipment.

Keep the AP away from radio stations, radar stations, high-frequency high-current devices, and microwave ovens.

Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electric shock, thus

causing severe even fatal damages to human bodies and device.

Direct or indirect touch through a wet object on high voltage and power line can bring a fatal danger.

2.4 Ventilation

For proper ventilation, leave sufficient space around the AP.

2.5 Temperature and Humidity

To ensure normal operation and service life of the device, maintain appropriate temperature and humidity levels in your

equipment room. See Table 2-1. Improper room temperature and humidity can cause damages to the device.

High relative humidity may affect insulation materials, resulting in poor insulation and even electrical leakage, and

sometimes may lead to change of mechanical properties of materials and corrosion of metal parts.

Low relative humidity may dry and shrink insulation sheets and cause static electricity that can damage the circuitry

inside the device.

High temperature greatly reduces reliability of the device and shortens its service life.

Table 2-1 Required Temperature and Humidity for the RG-AP820-L(V2)

Temperature

Relative Humidity

-10°C to 50°C (14°F to 122°F)

5% to 95%

2.6 Cleanness

Dust poses a serious threat to device operation. Dust that falls onto the surface of the device can be absorbed onto metal

contact points by static electricity, resulting in poor contact. Electrostatic absorption of dust occurs more easily when the

relative humidity is low, which may shorten the service life of the device and cause communication failures. Table 2-2

shows the maximum concentration and diameter of dust allowed in the equipment room.

Table 2-2

Maximum diameter (μm)

0.5

Maximum concentration

(Particles/m3)

1.4×107

7×105

2.4×105

1.3×105

Besides, the contents of salts, acids and sulfides in the air are also strictly limited for the equipment room. These

substances can accelerate metal corrosion and the aging of some parts. Table 2-3 describes the limit of some hazardous

gases such as SO2, H2S, NO2and Cl2 in the equipment room.

Table 2-3

Gas

Average (mg/m3)

Maximum (mg/m3)

SO2

0.2

1.5

H2S

0.006

0.03

NO2

0.04

0.15

NH3

0.05

0.15

Cl2

0.01

0.3

2.7 Power Supply

DC power adapter: 48V/0.3A

Specifications of Connector

Internal Diameter

External Diameter

Depth

Polarity

2.1mm

5.5mm

10mm

Internal: positive External: negative

2.8 Installation Tools

Common Tools

Phillips screwdriver, related copper and fiber cables, bolts, diagonal pliers, cable ties

Special Tools

Wire stripper, crimping pliers, RJ-45 crimping pliers, punch down tool

Meter

Multimeter, bit error rate tester (BERT)

The listed tools are customer supplied.

2.9 Unpacking the Access Point

Package Contents

Items

Verify that all parts are installed and debugged.

Screws

Mounting brackets

Product quick installation guide

Packing list

Inhaltsverzeichnis

Andere Ruijie Drahtloser Zugangspunkt Handbücher

Ruijie

Ruijie RG-AP180(V3) Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP6262 Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee Series Bedienungsanleitung

Ruijie

Ruijie RG-AP880-L Installations- und Betriebsanleitung

Ruijie

Ruijie RG-MAP852-SF-M Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP845-SP Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2260(G) Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP180-I Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP73HD Bedienungsanleitung

Ruijie

Ruijie RG-AP820-I Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP1201 Installations- und Betriebsanleitung

Ruijie

Ruijie RG-MAP852-SF-U Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP685-SP Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP680P-L Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP810-I Installations- und Betriebsanleitung

Ruijie

Ruijie AP630 Series Installationsanleitung

Ruijie

Ruijie RG-AP740-I Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP185-SP-W Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2200 Installations- und Betriebsanleitung

Ruijie

Ruijie RG-WLAN Series Bedienungsanleitung

Ruijie

Ruijie RG-AP680-IO Installations- und Betriebsanleitung

Ruijie

Ruijie RG-EAP602 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP750-SP Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP6262 Series Installations- und Betriebsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung