Ruijie RG-AP740-I Series Installations- und Betriebsanleitung

RG-AP740-I Series Access Point

Hardware Installation and Reference Guide V1.02

Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,

modification, transmission, translation or commercial use of this document or any portion of this document,

in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.

Exemption statement

This document is provided “as is”. The contents of this document are subject to change without any notice.

Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to

ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to

content omissions, inaccuracies or errors.

Hardware Installation and Reference Guide Product Overview

Preface

Thank you for using our products. This manual will guide you through the installation of the access point.

Scope

It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it

is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

Ruijie Networks Website: http://www.ruijienetworks.com/

Service Email: [email protected]

Technical Support: http://www.ruijienetworks.com/service.aspx

Technical Support Hotline: +86-4008-111-000

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that supported by the

product, with configuration examples.

Command Reference

Describes the related configuration commands, including command modes,

parameter descriptions, usage guides, and related examples.

Documentation Conventions

The symbols used in this document are described as below:

This symbol brings your attention to some helpful suggestions and references.

This symbol means that you must be extremely careful not to do some things that may damage the device or cause

data loss.

Hardware Installation and Reference Guide Product Overview

1 Product Overview

The RG-AP740-I AP uses Ruijie’s highly acclaimed X-Sense Smart Antenna and tops the class by supporting 802.11ac

Wave 2. Featuring nine spatial streams and MU-MIMO, the AP implements a leading tri-radio, dual-band design. The

three main radios deliver up to 1,734Mbps+800Mbps+433Mbps access rates and the third offers frequency spectrum

scanning. The whole AP speeds performance up to 2,967Mbps. The market-leading X-Sense Smart Antenna provides

better coverage and ensures the best access for mobile terminals. All models in the X-Sense AP Series support security,

radio frequency (RF) control, mobile access, Quality of Service (QoS) and seamless roaming. Teamed up with the Ruijie

RG-WS Wireless Controller Series, wireless data forwarding, high performance security and access control can be

accomplished with ease.

In addition, the RG-AP740-I AP (with tri-band and dual-radio design) flexibly supports 2.4G+5G+2.4G or 2.4G+5G+5G

working modes and concurrently 802.11ac Wave 2, 802.11ac Wave 1 and 802.11n. The AP can be mounted on a ceiling

or wall or on a pole. The AP supports local power supply and PoE to meet challenges in a wide variety of deployment

scenarios, including large-scaled campuses, enterprises, hospitals and WiFi hotspots.

1.1 Technical Specifications

Table 1-1 RG-AP740-I Technical Specifications

Model

RG-AP740-I

Tri-band, dual-radio

Transmission

Protocol

Three radio frequency cards support concurrent 802.11a/b/g/n, 802.11ac Wave 1 and 802.11ac

Wave 2.

Operating modes of 2.4G+5G+2.4G and 2.4G+5G+5G operating modes are supported.

Operating Bands

802.11b/g/n: 2.4GHz to 2.483GHz

802.11a/n/ac: 5.15GHz to 5.35GHz, 5.47GHz to 5.725GHz, 5.725GHz to 5.85GHz

(Country-Specific)

Antenna

Built-in X-Sense Smart Antenna array

Spatial Streams

9 streams: 4x4 SU-MIMO, 4x4 MU-MIMO, 1x1 SISO

Working Bandwidth

HT160(80+80), HT80, HT40, HT20

Max Throughput

802.11b/g/n: up to 800Mbps

802.11a/n/ac: up to 1,734Mbps and 433Mbps

Up to 2,967Mbps per AP

Modulation

OFDM: BPSK@6/9Mbps, QPSK@12/18Mbps, 16-QAM@24Mbps, 64-QAM@48/54Mbps

DSSS: DBPSK@1Mbps, DQPSK@2Mbps, and [email protected]/11Mbps

MIMO-OFDM: BPSK, QPSK, 16QAM , 64QAM and 256QAM

Receive Sensitivity

11a: -88dBm (6Mbps), -79dBm (24Mbps), -77dBm (36Mbps), -73dBm (54Mbps)

11b/g: -88dBm (6Mbps), -79dBm (24Mbps), -77dBm (36Mbps), -73dBm (54Mbps)

11n: -86dBm@MCS0, -68dBm@MCS7, -86dBm@MCS8, -68dBm@MCS15

11ac HT20: -83dBm (MCS0), -64dBm (MCS8)

11ac HT40: -80dBm (MCS0), -58dBm (MCS9)

11ac HT80: -77dBm (MCS0), -52dBm (MCS9)

11ac HT160(80+80): -74dBm (MCS0), -50dBm (MCS9)

Hardware Installation and Reference Guide Product Overview

Transmit Power

≤100mw (20dBm)

Transmit Power

Adjustment

1dBm

Dimensions

(W x D x H)

230mm x 230mm x 47mm (9.06in. x 9.06in. x 1.85in.)

Weight

1.3kg (2.87lbs)

Service Ports

Two 10/100/1000BASE-T Ethernet uplink ports (PoE-capable); one USB port

Management Ports

One Console port

Reset Button

Support

Anti-theft Locks

Support

LED

1 LED (red, green, blue and orange light for solid mode, flashing mode, or breathing flashing

mode, and the indicator can be switched off to silent mode)

Power Supply

Adapter: DC 48V (optional)

PoE: IEEE 802.3af/802.3at-compliant (compatible).

Dual PoE for power backup of the 802.3at or dual 802.3af power supplies

Note:

When power is supplied by dual 802.3at, USB is supported.

When power is supplied by single 802.3at, radio1 2.4G@1X4 and radio2 5G@3X4 modes are

supported.

Power Consumption

< 25.4W

Bluetooth

Bluetooth 4.0 (BLE) and Apple iBeacon protocol are supported. Bluetooth applications, such as

Shake and locating, can be extended.

Temperature

Operating: -10°C to 55°C (14°F to 131°F)

Storage: -40°C to 70°C (-40°F to 158°F)

Humidity

Operating: 5% to 95% (non-condensing)

Storage: 5% to 95% (non-condensing)

Installation

Ceiling/wall mount

IP Rating

IP41

Safety Standards

GB4943

EN/IEC 60950-1

EMC Standards

GB9254

EN301 489

Radio

China Radio Transmission Equipment Type Approval Certificate

EN300 328

EN301 893

Weight refers to the weight of host and bracket.

1.2 Product Image

The AP provides two 10/100/1000Base-T Ethernet ports (PoE-capable), one Console port, one power port for an external

power supply, one USB port and one reset button.

Figure 1-1 Appearance of the RG-AP740-I

Hardware Installation and Reference Guide Product Overview

Note

1. LED Indicator

2. Laptop lock

3. USB port

4. Reset button

5. LAN1/PoE Ethernet port

6. 48V DC power supply input port

7. Console port

8. LAN2/PoE Ethernet port

1.3 LED Indicators

Fit AP

State

Frequency

Meaning

Off

N/A

The AP is NOT receiving power in the Silent mode. This mode can be disabled

using software.

Blinking green

3Hz

Initialization is in progress. Continuously blinking green indicates abnormal

operation.

Blinking red

3Hz

Initialization is complete, but the Ethernet port is not connected.

Blinking blue

3Hz

Initialization is complete, and the AP is establishing a CAPWAP connection

with an AC.

Blinking orange

3Hz

Firmware upgrade in progress. Do not power off.

Solid blue

N/A

Normal operation, normal CAPWAP connection, but no wireless clients are

associated with the AP.

Breathing blue

Gradually fading

Normal operation, normal CAPWAP connection, at least one wireless client is

associated with the AP.

Solid red

N/A

Warnings (software defined )

Double blinking

red

3Hz (on and off for

2 cycles

alternately)

Locating AP

Fat AP

State

Frequency

Meaning

Hardware Installation and Reference Guide Product Overview

Off

N/A

The AP is NOT receiving power or in the Silent mode. This mode can be

disabled by software.

Blinking green

3Hz

Initialization is in progress. Continuously blinking green indicates abnormal

operation.

Blinking red

3Hz

Initialization is complete, but the Ethernet port is not connected.

Solid blue

N/A

Normal operation, but no wireless clients are associated with the AP.

Breathing blue

Gradually fading

Normal operation, at least one wireless client is associated with the AP.

Solid red

N/A

Warnings(defined by software)

Double blinking

red

3Hz (on and off for

2 cycles

alternately)

Locate AP.

1.4 Power Sources

The AP can be powered either with a power adapter or through Power over Ethernet (PoE).

To use a PoE device, make sure it supports the IEEE 802.3af/at PoE standard.

1.5 Cooling Solution

The AP adopts fanless design.

Leave sufficient space surrounding the AP when installing the AP to permit proper airflow for ventilation.

1.6 Radiation Pattern

The RG-AP740-I uses Ruijie’s patented X-Sense Smart Antenna. Regardless of the high mobility of smart devices, the AP

always provides the best signal path. Three radio patterns are shown in the following disgrams. The antennas focus gains

in front of the AP, so the signal strength in the front is stronger. It is preferable to install the AP towards the area that

requires the best wireless coverage.

When mounting the AP on a wall or ceiling, install the AP towards where you stand to avoid backward coverage.

Install the AP in a way that maximizes coverage.

When installing the AP indoors, it is better to mount it on the ceiling for greater coverage rather than on the wall.

Figure 1-2 and Figure 1-3 show the preferred wall-mount and ceiling-mount orientations of the AP operating in the 2.4

GHz and 5 GHz bands, respectively.

Figure 1-2 Preferred Ceiling-Mount and Wall-Mount Orientations of the RG-AP740-I (in the 2.4 GHz Band)

Hardware Installation and Reference Guide Product Overview

Figure 1-3 Preferred Ceiling-Mount and Wall-Mount Orientations of the RG-AP740-I (in the 5 GHz Band)

Hardware Installation and Reference Guide Preparing for Installation

2 Preparing for Installation

To prevent device damage and physical injury, please read the safety recommendations carefully as described in

this chapter.

Recommendations do not cover all possible hazardous situations.

2.1 Installation

The AP must be installed indoors. To ensure normal operation, the installation site must meet the following requirements.

Install the AP in a well-ventilated environment. If it is installed in a closed room, make sure there is a good cooling

system.

Make sure the site is sturdy enough to support the AP and its accessories.

Make sure the site has enough space for installing the AP and leave sufficient room around the AP for ventilation.

Do not expose the AP to high temperature, dust, or harmful gases.

Do not install the AP in an area prone to fire or explosions.

Keep the AP away from EMI sources such as large radar stations, radio stations, and substations.

Do not subject the AP to unstable voltage, vibration, and noises.

Keep the AP at least 500 meters away from the ocean and do not face it towards the sea breeze.

The installation site should be free from water including possible flooding, seepage, dripping, or condensation.

The installation site should be selected according to network planning and communications equipment features, and

considerations such as climate, hydrology, geology, earthquake, electrical power, and transportation.

Please follow the correct method described in the installation guide to install and remove the device.

2.2 Movement

Avoid frequently moving the device.

Turn off all power supplies and unplug all power cables before you remove the device.

2.3 EMI

Please observe local regulations and specifications when performing electrical operations. Relevant operators must

be qualified.

Carefully check for any potential hazards in the working area such as damp/wet ground or floors.

Find the location of the emergency power supply switch in the room before installation. Cut off the power supply first

in case of an accident.

Be sure to make a careful check before shutting down the power supply.

Hardware Installation and Reference Guide Preparing for Installation

Do not place the device in a damp/wet location. Do not let any liquid enter the chassis.

Keep the AP far away from grounding or lightning protection devices for power equipment.

Keep the AP away from radio stations, radar stations, high-frequency high-current devices, and microwave ovens.

Any nonstandard and inaccurate electrical operation can cause an accident such as fire or electric shock, thus

causing severe even fatal damages to humans and devices.

Direct or indirect contact with a wet object (or your finger) on the high voltage and power line can be fatal.

2.4 Ventilation

For proper ventilation, leave sufficient space around the AP.

2.5 Temperature and Humidity

To ensure the normal operation and equipment service life, maintain appropriate temperature and humidity levels in the

equipment room. See Table 2-1. Improper room temperature and humidity can cause damage to the device.

High relative humidity may affect insulation materials, resulting in poor insulation and even electrical leakage.

Sometimes it may lead to changes in the mechanical properties of materials and corrosion of metal parts.

Low relative humidity can dry and shrink insulation sheets and cause static electricity that can damage the circuitry.

High temperatures greatly reduce device reliability and shorten service life.

Table 2-1 Required Temperature and Humidity for the RG-AP740-I

Temperature

Relative Humidity

-10 to 55 ºC

5% to 95%

2.6 Cleanness

Dust poses a serious threat to device operation. Dust on the surface of the device can be absorbed onto metal contact

points by static electricity causing poor contact. Electrostatic absorption of dust occurs more easily when the relative

humidity is low, and might shorten the equipment service life and cause communication failures. Table 2-2 shows the

maximum concentration and diameter of dust allowed in the equipment room.

Table 2-2

Maximum diameter (μm)

0.5

Maximum concentration

(Particles/m3)

1.4 x 10

7 x 10

2.4 x 10

1.3 x 10

The amount of salt, acids and sulfides in the air are also strictly limited for the equipment room. These substances can

accelerate metal corrosion and aging of some parts. Table 2-3 describes the limits of some hazardous gases such as SO2,

H2S, NO2and Cl2 in the equipment room.

Table 2-3

Andere Handbücher für RG-AP740-I Series

Inhaltsverzeichnis

Andere Ruijie Drahtloser Zugangspunkt Handbücher

Ruijie

Ruijie RG-WLAN Series Bedienungsanleitung

Ruijie

Ruijie Reyee RG-RAP Series Bedienungsanleitung

Ruijie

Ruijie RG-AP840-I Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP825-SP Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP880-E Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2260 Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP52-OD Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP680-AR Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP180P-L Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP6262 Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP810-I Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP740-I Series Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP180(V3) Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2260(G) Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP130(W2) V2 Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP73HD Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP180-I Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP210-L Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP1200-MNT Series Installations- und Betriebsanleitung

Ruijie

Ruijie Reyee RG-RAP2200 Installations- und Betriebsanleitung

Ruijie

Ruijie RG-SAP150-SP-W Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP680-IO Installations- und Betriebsanleitung

Ruijie

Ruijie RG-MAP852-SF-U Installations- und Betriebsanleitung

Ruijie

Ruijie RG-AP730-L Series Installations- und Betriebsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung