Russell Hobbs RHMF80 Installationsanleitung

INSTRUCTIONS AND WARRANTY

MODEL NO. RHMF80

RUSSELL HOBBS MIST FAN

Congratulations on purchasing our Russell Hobbs Mist Fan. Each unit is manufactured

to ensure safety and reliability. Before using this appliance for the first time, please read

the instruction manual carefully and keep it for future reference.

IMPORTANT SAFEGUARDS

When using any electrical appliance, basic safety precautions should always be followed

including the following:

1. Please read the instructions carefully before using any appliance.

2. Always ensure that the voltage on the rating label corresponds to the mains voltage

in your home.

3. Incorrect operation and improper use can damage the appliance and cause injury to

the user.

4. The appliance is intended for household use only. Commercial use invalids the

warranty and the supplier can not be held responsible for injury or damage caused

when using the appliance for any other purpose than that intended.

5. Avoid any contact with moving parts.

6. Close supervision is required when any appliance is used near or by children or

invalids.

7. Check the power cord and plug regularly for any damage. If the cord or the plug is

damaged, it must be replaced by the manufacturer or a qualified person in order to

avoid an electrical hazard.

8. Do not use the appliance if it has been dropped or damaged in any way. In case of

damage, take the unit in for examination and/or repair by an authorised service agent

9. To reduce the risk of electric shock, do not immerse or expose the motor assembly,

plug or the power cord to water or any other liquid.

10. Never immerse the unit in water or any other liquid for cleaning purposes.

11. Remove the plug from the socket by gripping the plug. Do not pull on the cord to

disconnect the appliance from the mains. Always unplug the unit when not in use,

before cleaning or when adding or removing parts.

12. The use of accessory attachments that are not recommended or supplied by the

manufacturer may result in injuries, fire or electric shock.

13. A short cord is provided to reduce the hazards resulting from becoming entangled in

or tripping over a longer cord.

14. Do not let the cord hang over the edge of a table or counter. Ensure that the cord is

not in a position where it can be pulled on inadvertently.

15. Do not allow the cord to touch hot surfaces and do not place on or near a hot gas or

electric burner or in a heated oven.

16. Do not use the appliance on a gas or electric cooking top or over or near an open

flame.

17. Use of an extension cord with this appliance is not recommended. However, if it is

necessary to use an extension lead, ensure that the lead is suited to the power

consumption of the appliance to avoid overheating of the extension cord, appliance

or plug point. Do not place the extension cord in a position where it can be pulled on

by children or animals or tripped over.

18. This appliance is not suitable for outdoor use. Do not use this appliance for anything

other than its intended use.

19. DO NOT carry the appliance by the power cord.

20. Do not leave this appliance unattended during use. Always unplug the unit when not

in use or before cleaning.

21. Always operate the appliance on a smooth, even, stable surface. Do not place the

unit on a hot surface.

22. Ensure that the switch is in the “Off” position after each use.

23. The manufacturer does not accept responsibility for any damage or injury caused by

improper or incorrect use, or for repairs carried out by unauthorised personnel.

24. In case of technical problems, switch off the machine and do not attempt to repair it

yourself. Return the appliance to an authorised service facility for examination,

adjustment or repair. Always insist on the use of original spare parts. Failure to

comply with the above mentioned pre-cautions and instructions, could affect the safe

operation of this machine.

25. Never handle the power cord with wet hands as this could result in fire or electric

shock.

26. The water safety button will automatically switch off the fan when the fan runs out of

water in the tank.

PARTS DIAGRAM

HOW TO ASSEMBLE YOUR MIST FAN

1. Unpack all the parts of the fan and remove all packaging. Dispose of the packaging

safely.

2. Take out the base nut under the body.

3. Use the base nut to assemble the body to the base (black base holes

are in downward position).

4. Place and fix the wheels into their holes on the base and press them in

firmly. The wheels have been supplemented with the feature of clips.

Thus, you do not need to employ any screwdriver or special wrench to fix

the wheels.

5. Take out the blade cap from the shaft turning it clockwise.

6. Take out the rear guard mounting nut turning it anti-clockwise.

7. Insert the rear guard into the motor matching 3 rods on the front side of the motor

(the handle will direct upwards ) to 3 holes of the rear guard.

8. Fasten the rear guard tightly by turning the guard mounting nut clockwise.

9. Insert the blade to the shaft and ensure the pin enters the blade slot.

10. Tighten the blade using the blade cap turning anti-clockwise in the direction “TIGHT”

arrow on it.

11. Fix the front guard with the logo in the upright position on the rear guard. Make sure

that they are connected from the upper side.

12. Take the front guard rim and set in grooves of the rear and front gaurds, and fix it

with screwdriver.

Note: Do not operate the fan without assembling the guards properly and tightly.

13. Set one side mist tube 14 into front guard ornament 1, the other side mist tube

inserts the mist tube fixer. Then assemble finished.

FILLING THE HUMIDIFIER TANK

1. Open the water tank cover using the small flap on the right hand side of the unit.

2. Using the handle on the water tank, lift the water tank in an upward direction, and

pull it out.

3. Tip the water tank upside down and remove the screw cap. Add water to the tank, up

to 1.5 litres. Do not place any liquids in the water tank other than water. Only add

water that is room temperature. Do not use hot water in this unit.

4. Replace the screw cap, and make sure it is fully tightened.

5. Turn the water tank upright and place back into the body of the unit. Ensure that the

water tank sits firmly in the body. Close the water tank cover.

6. Your Russell Hobbs Mist Fan is now ready for use.

Note: Do not take out the water tank before unplugging the power cord. Hot

water (40℃and above) is not allowed to be added in the water tank.

Note: Do not add dirty or chalky water in your tank, add fresh water to ensure a

longer life for your fan.

OPERATING INSTRUCTIONS

Operating through Control Panel

1. Ensure the unit is on a firm, flat surface. Plug the unit into the wall socket and

switch on the wall socket. Use the remote control or the on-board control panel

to select the following:

2. Press “ON/SPEED” button, to choose the wind speed-Low,Med, High that

matches the light on the control panel.

3. Press” SWING” button, to change the wind direction, the corresponding light

will switch on.

4. Press this button again to stop the oscillation.

5. The wind angle of upwards and downwards is done manually. Set the desired

wind angle moving the guard and the motor of the fan up and down.

6. Press” MIST”button, if the light is on, the mist will spread out of the front mist

plate.

7. “MIST “button can be operated separately. Or worked together with the fan, this

will ensure cool wind. If the mist function is used separately, it can increase

humidity in the air.

Note: When the mist function is on, an apparent mist will be observed. Such

emission is normal and you do not have to change the settings of your appliance.

Do not take out the plastic tube in the front side of your fan. Otherwise, the metal

components of your fan will easily rust.

Operating through Remote Control

OFF

Switches off the fan and stands it by.

ON/SPEED

Switches on the stand-by fan and helps you choose the wind speed

Low, Med, High.

TIMER

Sets the time between 2 and 4 hours and switches the fan off after pre-

set time.

Press “TIMER”button to set the time using the timer function. There are

2 indicator lights of automatic timing. To set a time of 2 hours you need

to press the button once and to set 4 hours of running time you need to

press it 6 times and all the indicator lights will then go on.

SWING

Press “SWING”button, to change the wind direction, meanwhile the corresponding light

will switch on. Press this button again to stop oscillation.

MIST

“MIST” button can be operated separately, or worked together with the fan. This function

will create cool wind. If the mist function is used separately, it can increase humidity in

the air. After pressing the “MIST” button, mist will disperse from the mist plate.

To switch it off, press the “MIST”button again.

(Remote Control must be aimed at the infra-red port when using it. If the remote control

doesn’t work, check the inside battery, and change the batteries if needed.)

Notes: Change the batteries with the same type that was used previously. Otherwise

your remote control may not operate properly.

Remove the batteries out of the remote control if you won’t use the remote control for a

long time. Remaining batteries may damage your remote control.

CLEANING AND MAINTENANCE

This appliance is for household use only and is not user-serviceable.

Do not open or change any parts by yourself except to oil the unit. Please refer to

a qualified electrical service department or return to the supplier if servicing is

necessary.

Always remember to unplug the unit from the electrical outlet when not in use

and before cleaning. Ensure that the fan and humidifier are off before unplugging

the unit.

The body of the fan should be cleaned with a damp cloth. Do not let water enter

the motor or the body of the unit.

The water tank and plastic tube must be cleaned every two weeks when in

regular use. Remove the water tank as directed above, carefully pull the pipe out

of the mist cask (the tower that sits below the water tank), remove the mist cask

and clean both well.

Using a dry cloth, absorb all the water, and use a mild detergent to remove any

scale build-up. Replace the mist cask, insert the pipe into the mist cask, and

replace the water tank.

Do not use bleach or other abrasive substance or solvents to clean your fan as it

can be damaging to the finish.

Do not immerse the unit in water or any other liquid, or hold it under a running tap

to clean.

To remove stubborn spots/marks, wipe the surfaces with a cloth slightly

dampened in soapy water or mild non-abrasive cleaner. Rinse and dry a clean,

dry, soft cloth.

STORING THE APPLIANCE

Unplug the unit from the wall outlet and clean all the parts as instructed above.

Ensure that all parts are dry before storing.

Store the appliance in its box or in a clean, dry place.

Never store the appliance while it is still wet or dirty.

Never wrap the power cord around the appliance.

SERVICING THE APPLIANCE

There are no user serviceable parts in this appliance. If the unit is not operating

correctly, please check the following:

You have followed the instructions correctly

That the unit has been wired correctly and that the wall socket is switched on.

That the mains power supply is ON.

That the plug is firmly in the mains socket.

If the appliance still does not work after checking the above:

- Consult the retailer for possible repair or replacement. If the retailer fails to resolve the

problem and you need to return the appliance, make sure that:

The unit is packed carefully back into its original packaging.

Proof of purchase is attached.

A reason is provided for why it is being returned.

If the supply cord is damaged, it must be replaced by the manufacturer or an authorised

service agent, in order to avoid any hazard. If service becomes necessary within the

warranty period, the appliance should be returned to an approved Home of Living

Brands (Pty) Ltd service centre. Servicing outside the warranty period is still available,

but will, however, be chargeable.

CHANGING THE PLUG

Should the need arise to change the fitted plug, follow the instructions below.

This unit is designed to operate on 220V current only. Connecting to other power

sources may damage the appliance. Connect a three-pin plug as follows:

The wires in this mains lead are coloured in accordance with the following code:

Green/Yellow = Earth

Blue = Neutral

Brown = Live

PLEASE AFFIX YOUR PROOF OF PURCHASE/RECEIPT HERE

IN THE EVENT OF A CLAIM UNDER WARRANTY THIS RECEIPT MUST BE PRODUCED.

W A R R A N T Y

1. Home of Living Brands (Pty) Limited warrants to the original purchaser of this product (“the

customer”) that this product will be free of defects in quality and workmanship which under normal

personal, family or household use and purpose may manifest within a period of 1 (one) year from

the date of purchase (“warranty period”).

2. Where the customer has purchased a product and it breaks, is defective or does not work

properly for the intended purpose, the customer must notify the supplier from whom the customer

bought the product (“the supplier”) thereof within the warranty period. Any claim in terms of this

warranty must be supported by a proof of purchase. If proof of purchase is not available, then

repair, and/or service charges may be payable by the customer to the supplier.

3. The faulty product must be taken to the supplier's service centre to exercise the warranty.

4. The supplier will refund, repair or exchange the product in terms of this warranty subject to

legislative requirements. This warranty shall be valid only where the customer has not broken the

product himself, or used the product for something that it is not supposed to be used for. The

warranty does not include and will not be construed to cover products damaged as a result of

disaster, misuse, tamper, abuse or any unauthorised modification or repair of the product.

5. This warranty will extend only to the product provided at the date of the purchase and not to any

expendables attached or installed by the customer.

6. If the customer requests that the supplier repairs the product and the product breaks or fails to

work properly within 3 (three) months of the repair and not as a result of misuse, tampering or

modification by or on behalf of the customer, then the supplier may replace the product or pay a

refund to the customer.

7. The customer may be responsible for certain costs where products returned are not in the original

packaging, or if the packaging is damaged. This will be deducted from any refund paid to the

customer.

HOME OF LIVING BRANDS (PTY) LTD (JOHANNESBURG)

JOHANNESBURG TEL NO. (011) 490-9600

CAPE TOWN TEL NO. (021) 552-5161

DURBAN TEL NO. (031) 792-6000

www.homeoflivingbrands.co.za

Inhaltsverzeichnis

Sprachen:

Andere Russell Hobbs Lüfter Handbücher

Russell Hobbs

Russell Hobbs SCANDI Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHPF100 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHPDF0911 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHMP01 Installationsanleitung

Russell Hobbs

Russell Hobbs RHMPF4 Installationsanleitung

Russell Hobbs

Russell Hobbs RHFF56 Installationsanleitung

Russell Hobbs

Russell Hobbs RHDF 30 Installationsanleitung

Russell Hobbs

Russell Hobbs RHMF40 Installationsanleitung

Russell Hobbs

Russell Hobbs RHTF3201 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHHV50 Installationsanleitung

Russell Hobbs

Russell Hobbs RHMDF1211CH Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHPF-40 Installationsanleitung

Russell Hobbs

Russell Hobbs RHDF12 Installationsanleitung

Russell Hobbs

Russell Hobbs RHDF 30 Installationsanleitung

Russell Hobbs

Russell Hobbs RHOFF18 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHPDF1211 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHHV45 Installationsanleitung

Russell Hobbs

Russell Hobbs RHMPF1611CH Bedienungsanleitung

Russell Hobbs

Russell Hobbs SCANDI Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHTF1401 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHPF-40 Installationsanleitung

Russell Hobbs

Russell Hobbs RHOMF8 Installationsanleitung

Russell Hobbs

Russell Hobbs RTF-40 Installationsanleitung

Russell Hobbs

Russell Hobbs RHPPF1611 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung