RVi TBC1 Bedienungsanleitung

Towed Battery Charger

Instructions

Thanks for purchasing the Towed Battery Charger!

Contents Include:

a) Maintainer Control Box with wiring harness.

b) 5 Wire Ties

c) 4 mounting screws

Connecting to the towed battery:

2) In your towed vehicle, remove the nut on the positive battery terminal

and place the red ring terminal over the bolt and then retighten the nut

back onto the bolt. Remove the nut on the negative battery terminal,

place the blue ring terminal over the bolt, and retighten the nut back on

to the bolt.

Mounting Control Box:

1) Find a location near the towed vehicles battery to

mount the box. This location should allow you to

easily route the duplex wire to the vehicle battery

terminals. Use 2 wire ties to hold the box in place.

You can mount the box along the inner fender or

elsewhere, using the provided mounting screws

Fig. 1

Connecting TBC to towed umbilical connector:

3) Locate the multi-pin connector near the front of

your vehicle. Route the TBC single wire labeled

“Motorhome,” safely through the engine compartment

or fender to the front of the vehicle where this

connector is located.

4) Identify the positive 12VDC terminal in the multi-pin

connector where the wires come into the towed vehicle.

Strip the end of the single wire from the TBC and insert the wire into

the multi-pin connector. Securely tighten. You may shorten the wire

then attach it to your connector. You will need to ensure there is a

constant 12VDC supply to this connector routed from your motorhome

through your umbilical cord!

5) Inspect for any loose or dangling wire, and secure as necessary with

the wire ties provided.

Fig. 2

NOTES:

You will need to ensure that there is a constant 12V

supply to the multi-pin connector routed from your

motorhome through your umbilical cord. You will also

need to ensure that there is a proper ground from the

back of the multi-pin connector on your towed vehicle

to the towed chassis. (Fig. 3)

The LED will ﬂash when all connections are correct and if there is a

charge coming from your motorhome, this may mean starting the

engine of the motorhome. If it is not ﬂashing, check all terminal

connections, the fuse, or the 12 Volt supply from your motorhome.

Vehicles with rear mounted batteries, consult your owner’s manual to

ﬁnd the jump start lug, and appropriate ground source for completing

step 4.

Fig. 3

Failure to connect the TBC according to the instructions, may result in

damage to your charge circuit or other electronics, in which RVi is not

responsible.

WARNING: If you have to disconnect the towed vehicles battery for towing,

then it is recommended to disconnect the negative and positive terminal.

Failure to do so can cause damage on the towed vehicle.

Please contact our customer service department at (800) 815-2159

if you have any questions regarding the installation of the Towed

Battery Charger.

towedcharger.com

Inhaltsverzeichnis

Andere RVi Autozubehör Handbücher

RVi

RVi RVibrake3 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung