Saluki CSA Series Bedienungsanleitung

CSA Series Signal Analyzer

User Manual

Saluki Technology Inc.

Tel: 886. 909 602 109 Email: [email protected]

www.salukitec.com

The document applies to the signal analyzer of the following models:

CSA2026 Signal Analyzer (100 kHz - 26.5 GHz)

Standard pack and accessories:

1×Signal Analyzer Host

1 × USB Power Adapter

1 × Power Cord

1 × USB Cable (USB3.1, Type-C to USB-A)

1 × U Disk (Software & User Manual)

1 × Certificate of Calibration

1 × Carrying Case

Options of the CSA series signal analyzer:

Module No.

Item

Description

P26

Pre-amplifier

B40

40MHz Analysis Bandwidth

To output real-time signal acquisition data through optical fiber

and support signal data output with maximum 40MHz

bandwidth.

HAS

High Resolution Step Attenuator

0-50dB, 2dB step

PFR

Precision Frequency Reference

RTA

Real Time Analysis

Tel: 886. 909 602 109 Email: [email protected]

www.salukitec.com

Preface

Thank you for choosing Saluki Technology Products.

We devote ourselves to meeting your demands, providing you high-quality measuring instrument and the best after-sales

service. We persist with “superior quality and considerate service”, and are committed to offering satisfactory products and

service for our clients.

Document No.

CSA2026-03-01

Version

Rev01 2022.04

Saluki Technology

Document Authorization

The information contained in this document is subject to change without notice. The power to interpret the contents of and

terms used in this document rests with Saluki.

Saluki Tech owns the copyright of this document which should not be modified or tampered by any organization or individual,

or reproduced or transmitted for the purpose of making profit without its prior permission, otherwise Saluki will reserve the right

to investigate and affix legal liability of infringement.

Product Quality Assurance

The warranty period of the product is three years from the date of delivery. The instrument manufacturer will repair or replace

damaged parts according to the actual situation within the warranty period.

Product Quality Certificate

The product meets the indicator requirements of the document at the time of delivery. Calibration and measurement are

completed by the measuring organization with qualifications specified by the state, and relevant data are provided for

reference.

Quality/Settings Management

Research, development, manufacturing and testing of the product comply with the requirements of the quality and

environmental management system.

Tel: 886. 909 602 109 Email: [email protected]

www.salukitec.com

Contact

Service Tel:

886. 909 602 109

Website:

www.salukitec.com

Email:

sales@salukitec.com

Address:

No. 367 Fuxing N Road, Taipei 105, Taiwan (R.O.C.)

Safety Notice

The instrument casing can prevent users from touching the internal parts of the instrument, but the casing is not

waterproof. Please cut off the power as soon as possible when liquid enters the interior.

The produce has fans inside to stabilize the inner temperature, please do not block ventilation window on both

sides of the product. When the instrument needs to be installed in an enclosed space, please keep the air

circulation in the enclosure to ensure the stability of the instrument's performance.

The RF input port on the front panel can withstand a maximum AC signal power of +27dBm or a DC voltage

input of 16V (the duration does not exceed 1 minute). Exceeded the limit may cause the internal circuit damaged

and device malfunction.

Tel: 886. 909 602 109 Email: [email protected]

www.salukitec.com

Contents

1 Overview................................................................................................................................................................... 6

2 Start To Use.............................................................................................................................................................. 7

2.1 Software Installation..........................................................................................................................................7

2.2 Hardware Connection........................................................................................................................................8

2.3 Confirmation of Connection Status..................................................................................................................... 8

2.4 Front Panel Description................................................................................................................................... 10

2.5 Rear Panel Description....................................................................................................................................10

3 Software Function Description................................................................................................................................ 12

4 Remote Control....................................................................................................................................................... 15

Tel: 886. 909 602 109 Email: [email protected]

www.salukitec.com

1 Overview

The CSA series signal analyzer meets your signal observation and analysis needs in the 100 kHz to maximum 26.5 GHz

frequency range. You can use it to measure and observe a variety of signal characteristics for manufacturing, R&D, repair service,

and education. The highlights of the product are as follows:

Modular instrument, taking into account both performance and portability

Support firmware online upgrade, easily software update

Temperature calibration range 0-50℃, wide temperature version is available

Multi-function: spectrum analysis mode, IQ analysis mode, phase noise measure mode

Many measurement components available

The remote control interface is compatible with most instruments

Confidence level of 99% specification guarantee

Analysis bandwidth 25M/40MHz Optional

Fast scroll frequency sweep technology

This manual is written according to CSA2026 and its software kit A1000A version A27.28. Since we are constantly updating the

product software to better meet your demands, please download the latest user manual on the Saluki website (www.salukitec.com)

in time.

Tel: 886. 909 602 109 Email: [email protected]

www.salukitec.com

2 Start To Use

2.1 Software Installation

The CSA series signal analyzer itself do not have a display interface, and the parameter settings and display function are provided

by the A1000A software running on PC. The software that controls this product needs to be installed on the PC before use. You

can download or run the installer on the CD-ROM from the Saluki website. This software installation package runs on Microsoft

Windows systems, 32-bit and 64-bit versions are all available.

The installation files provided on the CD-ROM only support Windows XP sp1 and above operating systems. If you use another

version of the operating system, please contact your Saluki dealer or FAE service for further information.

Run the installer by double click, specify the installation location and select Install. The installer will automatically complete the

installation steps.

The installation will launch the USB driver installation automatically. Please follow the installation prompts to install the USB driver,

as shown in Fig. 1.

Fig. 1 Install the USB driver

After the installation of the USB driver, the installer will launch ofMicrosoft .Net Framework installation, as shown in Fig. 2. If your

computer already has a correct version of .Net Framework, Windows will prompt you do not need to install it. Follow the system

prompts.

Fig. 2 Install .Net Framework

After the steps all above, the installer will prompt that the installation is complete. Click Finish to complete the installation.

Tel: 886. 909 602 109 Email: [email protected]

www.salukitec.com

2.2 Hardware Connection

Insert USB cable’s Type-C plug into (1) and insert the AC/DC power adapter’s DC plug into (3) on the rear panel. If the power is

OK, the indicator button (2) LED light will light up for 3 seconds. then goes out, indicating the device is in standby mode.

The specification of the power adapter is 220VAC-12VDC/10A. The USB cable is a Type-C to USB-A cable with locking screws,

which meets the USB3.0 standard.

The AC to DC adapter in accessories is 220VAC-12V/10A. The DC socket is a LEMO FGG.1B.302 fast-lock connector. The USB

cable is a Type-C to USB-A cable with locking screws. The cable meets the transfer rate requirement for USB3.1 standard.

Fig. 3 Connect the Power Adapter and USB Cable

If you need the CSA2026 to share the ground with the AC power supply system, you need to connect your ground wire

to the metal part of the CSA2026 case.

Please be sure to fasten the Type-C locking screws. Mass of tests shown that the plug-in force of Type-C socket

cannot guarantee the stable connection in various situations. Please make sure that the USB port of the PC meets the

USB3.0 specification. An unstable connection will cause the software fails to work.

2.3 Confirmation of Connection Status

After connecting the PC correctly, enter the “Device Manager” of the Windows Control Panel to check whether the CSA2026 is

recognized by the system. Three devices should be recognized and works properly, namely Cypress FX3 USB Device, Generic

USB Hub, and USB Mass Storage Device, as shown in Fig. 4.

Tel: 886. 909 602 109 Email: [email protected]

www.salukitec.com

Fig. 4 Check whether CSA2026 is correctly identified in “Device Manager”

The CSA2026 has a 32GB built in Flash memory to store the copy of the CSA software A1000A. Users can run this

copy directly without installing the software(For Windows10 and later versions). Users can also use this Flash memory

for other purposes.

Double-click the software icon to launch the A1000A software. For the first-time connecting, the software will automatically check

whether the USB driver is updated and install the correct version. Please wait for the system prompt to complete the driver update

until you see the prompt of the wizard (as shown in Fig. 5). This step will not be repeated after first time connection.

Fig. 5 The USB driver is automatically installed (when connecting for the first time)

The software will automatically complete the initialization, read the device calibration and configuration data and enter the working

state. During initialization you will see a boot screen (.as shown in Fig. 6 ,left). When you see the software working interface (.as

shown in Fig. 6 , right), it proves that the USB connection and hardware status are correct.

Tel: 886. 909 602 109 Email: [email protected]

www.salukitec.com

Fig. 6 Boot screen (left). Work mode interface(right)

2.4 Front Panel Description

The front panel is shown in Fig. 7. The function of each element is described below:

Fig. 7 Elements in front panel

1. RF Input — 2.92-K type steel connector, 50 ohm matched impedance.

2. Status Indicator — Orange: Standby mode. Green: Working mode. Red: Hardware error.

3. Intermediate frequency output — SMA type interface, the analog intermediate frequency signal output port.

4. Trigger input1 — SMA type interface, the trigger signal 1 input, 0~5V input voltage range.

5. Trigger input2 — SMA type interface, the trigger signal 1 input, 0~5V input voltage range.

6. Reference input — SMA type interface, Connect to 10 MHz external reference source for reference synchronization.

7. Reference source output — SMA type interface, 10 MHz internal reference signal output for reference synchronization.

2.5 Rear Panel Description

The rear panel is shown in Fig. 8. The function of each element is described below:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Saluki Messgerät Handbücher

Saluki

Saluki S3602 Series Bedienungsanleitung

Saluki

Saluki S3531 series Bedienungsanleitung

Saluki

Saluki STB8827 Series Bedienungsanleitung

Saluki

Saluki S3302E Bedienungsanleitung

Saluki

Saluki S2106 Series Bedienungsanleitung

Saluki

Saluki SK400 Bedienungsanleitung

Saluki

Saluki S5105 Series Bedienungsanleitung

Saluki

Saluki S3101 Series Bedienungsanleitung

Saluki

Saluki S3331 Series Gebrauchsanweisung

Saluki

Saluki S3331B Bedienungsanleitung

Saluki

Saluki S3101 Series Bedienungsanleitung

Saluki

Saluki S3302 Series Bedienungsanleitung

Saluki

Saluki S2438 Series Bedienungsanleitung

Saluki

Saluki S3331 Series Betriebsanleitung

Saluki

Saluki S3302SB Bedienungsanleitung

Saluki

Saluki ADS2202A Bedienungsanleitung

Saluki

Saluki S2106S Series Bedienungsanleitung

Saluki

Saluki S5800E Series Bedienungsanleitung

Saluki

Saluki SE3001 Bedienungsanleitung

Saluki

Saluki S3602 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung