Salus QUANTUM SQ610RF Bedienungsanleitung

Connect it with Universal

Gateway and setup your

own SALUS Smart Home

system

Pair it with Quantum

to achieve the perfect

temperature everywhere,

not only beside the radiator

Connect it with Universal

Gateway and control

wirelessly pumps, valves,

boilers, lighting etc

Wireless room thermostat

Funkraumthermostat

Thermostat numérique sans l à piles

Беспроводной терморегулятор с питанием от батареи

Trådløs rumtermostat

Trådlös rumstermostat

Trådløs romtermostat

Langaton huonetermostaatti

Bezprzewodowy regulator temperatury, bateryjny

Bezdrátový pokojový termostat (napájení baterie)

Termostat cu radio frecvență, cu baterii

Kablosuz oda termostati

Controlador radiofrecuencia recargable

Termostato wireless a batteria

Безжичен стаен термостат с батерии

Bežični sobni termostat, baterijski napajan

5YEAR

WARRANTY

Introduction

The SQ610RF Quantum is a ZigBee temperature controller for wireless control of iT600 series devices, such as

the KL08RF wiring centre, miniTRV head, RX10RF boiler control module.

In order to control SQ610RF over the Internet or via the SALUS Smart Home mobile app (ONLINE mode),

it must be installed together with the UGE600 Internet gateway (sold separately). From the application level,

it is possible to pair SQ610RF with other system elements, e.g. Smart Plug SPE600, Smart Relay SR600 or

window/door sensor OS600/SW600.

SQ610RF can be used locally without an Internet connection (OFFLINE mode), however, it’s communication

with other devices must be done using the CO10RF coordinator (sold separately).

Full manual in PDF format is available at www.salus-controls.eu site.

UseinaccordancetonationalandEUregulations.Use the deviceas intended,keeping itin drycondition. Product for

indoor use only. Installation must be carried out by a qualied person in accordance to national and EU regulations.

Disconnect your equipment before cleaning it with a dry cloth.

Product Compliance

Safety Information

This product complies with the essential requirements and other relevant provisions of Directives 2014/30/ EU,

2014/35/EU, 2014/53/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the

following internet address: www.saluslegal.com.

Package Content:

1) SQ610RF QuantumThermostat

2)Wall mounting plate

3) Self-adhesive mounting tape

4) Mounting screws

5) Manual instruction

Before you start:

Charging to full battery level may take up to

24h maximum.

New SQ610RF Quantum Thermostat is partially

charged, however, we recommend you to fully

charge the battery before use.

Connect charger to micro-USB Port which is at

the bottom of SQ610RF Quantum Thermostat to

charge the device.

Wiring diagram (S1, S2 Input)

Symbols explanation:

S – volt-free contact

T – temperature sensor

S1,S2 Terminals:

- air or oor temperature sensor

- external volt-free contact to connect any

ON/OFF switch or occupancy sensor (Hotel card)

Mounting: to mount thermostat you can use

included accesories (mounting screws or

self-adhesive tape). Remove back cover

to mount the plate to the wall. After this just

attach thermostat to the plate (it has built-in

magnet).

Please note:

The ideal position to thermostat mounting is about

1,5m under oor level far from heating or cooling

sources. Thermostat can’t be exposed to sunlight

or any extreme conditions like for example draft.

1 2

Español Deutsch

Português English

1. Menu/Settings description + Clock

2. AM/PM

3. Temperature unit

4. Heating indicator (icon is animating when

there is heating demand)

5. Cooling indicator (icon is animating when

there is cooling demand)

6. RF Connection indicator

7. Internet connection indicator

8. Occupancy sensor (hotel card)

9. Key lock function

10. Standby mode icon

11. Current Temperature / Setpoint Temperature

12. Holiday mode

13. Temporary override mode

14. Settings icon

15. Baterry status indicator

16. External / Floor temp sensor indicator

17. Schedule program number

18. Schedule mode icon

19. Day indicator/ SET information

20. Current Humidity value

10111214

LCD Icon Description

Buttons DescriptionButtons Description

1) Menu button / Return button.

2) In the MAIN SCREEN: Press and hold for 3 sec to change the thermostat operating mode

(Schedule mode / Permanent mode /Temporary override mode).

3) In the SETTINGS SCREEN:

Press and hold for 3 sec to go back without saving the changes.

4) In the PAIRING SCREEN (in SYSTEM TYPE Menu): Press and hold for 3 sec to see other

pairing options.

In the MAIN SCREEN - press and hold these buttons together for 3 seconds to LOCK / UNLOCK

the Thermostat keys).

“Up”Button (Increase parameter value/moving on the menu in‘UP’direction)

„Down”Button (Decrease parameter value/moving on the menu in‘DOWN’direction)

1) Press and hold for 3 seconds to POWER UP new device

2)“OK / Tick”Button (Conrm parameter value / Go to the next menu / Save settings)

3) In the MAIN SCREEN: Press and hold for 3 seconds to enter Standby mode

4) In the SETTINGS SCREEN: Press and hold for 3 sec to go back to the MAIN SCREEN & SAVE all the changes.

5) During PAIRING process – hold button for 3 seconds to POWER OFF or REBOOT the thermostat.

Button Function

Español Deutsch

Português English

COMPATIBILTY WITH OTHER SALUS CONTROLS DEVICES

QuantumThermostat can work in ONLINE or OFFLINE mode.QuantumThermostat can work in ONLINE or OFFLINE mode.

At rst step you need to decide in which mode your thermostat will work.At rst step you need to decide in which mode your thermostat will work.

ONLINE MODE OFFLINE MODE

Universal Gateway is

CONNECTED TO THE INTERNET

You can congure and use all your

devices in the Smart Home App

Download the Smart Home

App on your iOS or Android

device for remote access to your

SALUSequipment. SALUS

Smart Home

CO10RF Coordinator - You can use

standard ZigBee network coordinator

toinstall and use your devices.

Universal Gateway is NOT

CONNECTED TO THE INTERNET

You can use your devices locally

without the SmartHome App.

Gateway works in this mode as

standard ZigBee coordinator.

Compatibile devices:

KL08RF

Wiring Centre for 8-zone

underoor heating (UFH).

TRV

(Thermostatic

Radiator Valve) with

wireless communication.

RX10RF

receiver

SR600*

Smart Relay SPE600*

Smart Plug

*Only with Online Mode

GET IT ON

Download on the

First power up sequence

To power on the Thermostat hold

button for 3 seconds...

3 sec.

For easier installation, please make sure you have already added other devices to your ZigBee network, such as

Underoor Heating Control Box (KL08RF) or Radiator heads (TRV’s) etc.

Please note:

Now, choose your language by

„” or „ ” buttons. Conrm

your language by button.

...display will showall icons...

...then thermostat will display

the software version.

MENU / Press for 3 sec

to POWER UP

For more information

scan this code or visit:

www.salus-controls.com

3 sec

Removetheprotection foil

Español Deutsch

Português English

Installation in ONLINE mode

AfterLanguage selection follow below stepsto add yourdevice to the Smart Home app and pair with other devices:

SALUS

SmartHome

Go to SALUS Smart Home app

Once your thermostat is added to

the app you will see above screen

on the LCD.

11 1210

13 14 15

Name this equipment

SQ610RF Thermostat

Connect equipment

Finish

After that thermostat will display

main screen.

Congratulations!You succesfully

congured SQ610RF Quantum

Thermostat.

Español Deutsch

Português English

Installation in OFFLINE mode

Pairing with Wiring Centre / Control Box (Install the Wiring Centre / Control Box according to

the instructions included with product)

123

Open the ZigBee network

Select system type: UNDERFLOOR,

press button to conrm.

Using and buttons select theControl

Box number (press PAIR button on the Control

Box to see its address number). Press

button to conrm.

Use or buttons to select

the zone number and press

button to conrm.

Now you can pair your thermostat

with additional zones. Select one

more zone or nish the pairing process

by button.

5 sec.

Close the ZigBee network

5 sec.

Andere Handbücher für QUANTUM SQ610RF

Inhaltsverzeichnis

Sprachen:

Andere Salus Thermostat Handbücher

Salus

Salus HTR2420 Bedienungsanleitung

Salus

Salus FC600 Bedienungsanleitung

Salus

Salus RT510 Bedienungsanleitung

Salus

Salus RT300 Bedienungsanleitung

Salus

Salus ERT50 Bedienungsanleitung

Salus

Salus VS30W Bedienungsanleitung

Salus

Salus FC600-M Bedienungsanleitung

Salus

Salus TH-3 Bedienungsanleitung

Salus

Salus RT310i Bedienungsanleitung

Salus

Salus iT500BM Benutzerhandbuch

Salus

Salus ST910WZ CA Bedienungsanleitung

Salus

Salus PH60 Bedienungsanleitung

Salus

Salus ERT50T Triac Bedienungsanleitung

Salus

Salus ERT30 Bedienungsanleitung

Salus

Salus RT510LG5V Bedienungsanleitung

Salus

Salus RT510RF Bedienungsanleitung

Salus

Salus PH60 Bedienungsanleitung

Salus

Salus RT310SR Bedienungsanleitung

Salus

Salus iT500 Benutzerhandbuch

Salus

Salus RT500 Bedienungsanleitung

Salus

Salus AWRT10RF Bedienungsanleitung

Salus

Salus Quantum WQ610 Bedienungsanleitung

Salus

Salus CT100 Bedienungsanleitung

Salus

Salus Quantum WQ610 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung