Samson RS Series Bedienungsanleitung

Owner's Manual

Active Loudspeakers with Bluetooth®

Samson Technologies Corp.

278-B Duffy Ave

Hicksville, New York 11801

www.samsontech.com

If you want to dispose this product, do not mix it with general household waste. There is

a separate collection system for used electronic products in accordance with legislation

that requires proper treatment, recovery and recycling.

Private household in the 27 member states of the EU, in Switzerland and Norway may

return their used electronic products free of charge to designated collection facilities or to a

retailer (if you purchase a similar new one).

For Countries not mentioned above, please contact your local authorities for a correct method of

disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment,

recovery and recycling and thus prevent potential negative effects on the environment and

human health.

Important Safety Information

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This lightning ﬂash with arrowhead symbol within an equilateral triangle is intended

to alert the user to the presence of non-insulated “dangerous voltage” within the

product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of

electric shock.

The exclamation point within an equilateral triangle is intended to alert the user

to the presence of important operating and maintenance instructions in the

literature accompanying the appliance.

AVIS

RISQUE DE CHOC ÉLECTRONIQUE -

NE PAS OUVRIR

ENGLISHFRANÇAISDEUTSCHEESPAÑOLITALIANO

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. This apparatus shall not be exposed to

dripping or splashing liquid and no object

ﬁlled with liquid, such as a vase, should

be placed on the apparatus.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation

openings. Install in accordance with the

manufacturer’s instructions. Minimum

5cm around the apparatus for sufﬁcient

ventilation

8. Do not install near any heat sources such

as radiators, heat registers, stoves, or

other apparatuses (including ampliﬁers)

that produce heat.

9. Only use attachments/accessories

speciﬁed by the manufacturer.

10. Unplug this apparatus during lightning

storms or when not in use for long

periods of time.

11. Do not override the intended purpose

of the polarized or grounding-type plug.

A polarized plug has two blades, with

one wider than the other. A grounding-

type plug has two blades and a third

grounding prong. The wide blade, or third

prong, is provided for your safety. If the

provided plug does not ﬁt your outlet,

consult an electrician to replace the

obsolete outlet.

12. Protect the power cord from being walked

on or pinched, particularly at the prongs,

convenience receptacles, the point where

they exit from the apparatus.

13. Use only with the cart stand, tripod

bracket, or table speciﬁed by the

manufacture, or sold with the

apparatus. When a cart is used,

utilize caution when moving the

cart/apparatus combination to

avoid injury from tip-over.

14. Refer all servicing to qualiﬁed service

personnel. Servicing is required if the

apparatus has been damaged in any

way, such as power-supply cord or

plug breakage, damage due to liquid

or objects falling onto the apparatus,

exposure to rain or moisture, or if the

apparatus does not operate normally, or

has been dropped.

15. POWER ON/OFF SWITCH: For products

with a power switch, the power switch

DOES NOT break the connection from

the mains.

16. MAINS DISCONNECT: The plug should

remain readily operable. For rack-

mount or installation where plug is not

accessible, an all-pole mains switch with

a contact separation of at least 3 mm

in each pole shall be incorporated into

the electrical installation of the rack or

building.

17. FOR UNITS EQUIPPED WITH

EXTERNALLY ACCESSIBLE FUSE

RECEPTACLE: Replace fuse with same

type and rating only.

18. MULTIPLE-INPUT VOLTAGE: This

equipment may require the use of a

different line cord, attachment plug,

or both, depending on the available

power source at installation. Connect

this equipment only to the power source

indicated on the equipment rear panel.

To reduce the risk of ﬁre or electric

shock, refer servicing to qualiﬁed service

personnel or equivalent.

Important Safety Information

3RS Active Loudspeakers with Bluetooth®

FCC Notice

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause

undesired operation.

2. Changes or modiﬁcations not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20

centimeters between the radiator and your body.

RF Warning Statement

The device has been evaluated to meet general RF exposure requirement. The device can be

used in portable exposure condition without restriction.

This device complies with RSS-310 of Industry Canada. Operation is subject to the condition

that this device does not cause harmful interference.

Hereby, Samson Technologies Corp., declares that this RS110A, RS112A and RS115A are in

compliance with the essential requirements and other relevant provisions of Directive 2014/53/

EU. The declaration of conformity may be consulted at:

http://www.samsontech.com/site_media/support/manuals/RS112A_DOC.pdf

Important Safety Information

ENGLISHFRANÇAISDEUTSCHEESPAÑOLITALIANO

Thank you for purchasing the Samson RS series active loudspeaker with Bluetooth®. RS series

loudspeakers provide the functionality of a powered speaker with the RS110A featuring 300

watts, and RS112A/RS115A featuring 400 watts of bi-amped power, as well as versatility of a

portable PA system with an onboard mixer. Ideal for live music, DJ, lecture, and portable sound

applications.

The RS110A has a heavy-duty 10” low-frequency driver while the RS112A and RS115A

have 12” and 15” low-frequency drivers respectively. All three models have a 1” high

frequency driver mounted in wide-dispersion horn, providing crystal-clear audio and an

ultra-wide sound ﬁeld. The rear panel three-channel mixer includes two XLR and 1/4” inputs

that handle microphone or line level signals, a 3.5mm aux input and Bluetooth connectivity

for streaming music. The two Mic/Line channels include a variable compressor for evening

out the input signals. There is also a USB Wireless port for connecting Samson XPD Series

wireless microphone systems. An XLR Mix Output allows you to daisy-chain additional powered

loudspeakers to create larger sound reinforcement systems. The cabinet’s trapezoidal shape

allows it to be conﬁgured for either front-of-house use, for operation as a wedge-style monitor,

or can be stand-mounted using the integral 1 3/8” pole-mount receptacles.

In these pages, you’ll ﬁnd a detailed description of your RS Loudspeaker, as well as step-by-

step instructions for its setup and use. If your loudspeaker was purchased in the United States,

you’ll also ﬁnd a registration card enclosed — don’t forget to follow the instructions so that you

can receive online technical support and so that we can send you updated information about

this and other Samson products in the future. Also, be sure to check out our website

www.samsontech.com for complete information about our full product line.

We recommend you keep the following records for reference, as well as a copy of your sales receipt:

Serial number: ________________________________________________

Date of purchase: ______________________________________________

If you have any questions or comments regarding the RS Loudspeaker or any other products

from Samson, do no hesitate to contact us at support@samsontech.com.

With proper care and maintenance, your RS Loudspeaker will operate trouble-free for many years.

Should your RS Loudspeaker ever require servicing, a Return Authorization (RA) number must be

obtained before shipping your unit to Samson. Without this number, the unit will not be accepted.

Please visit www.samsontech.com/ra for an RA number prior to shipping your unit. Please retain

the original packing materials and, if possible, return the unit in its original carton. If your RS

Loudspeaker was purchased outside of the United States, contact your local distributor for warranty

details and service information.

Introduction

5RS Active Loudspeakers with Bluetooth®

1. XLR & 1/4” Combo Input - Use

these XLR - 1⁄4” input for

balanced microphone or line level

devices.

2. SENSITIVITY Switch (Mic/Line) -

Matches the channel sensitivity to

the input audio source signals.

3. COMPRESSOR - These knobs

adjust the level of compression

applied to the channel. As the

knob is turned clockwise, the

compression ratio is raised

and the output gain is adjusted

accordingly. The dynamic range

of the channel is narrowed, where

softer signals will be magnified

and loud signals will be subdued

to sit better in the mix. Too

much compression can create

a pumping effect, eliminate

all dynamic range, and lead to

feedback.

4. Volume Control - This knob adjusts

the level of the Channel 1 and 2

input signals.

5. Pairing Indicator - Displays the

Bluetooth®status of the RS

loudspeaker.

6. Pairing Button - Press this button

to enable discoverable mode to

pair with a Bluetooth audio device.

7. Volume Control - This knob adjusts

the level of the Bluetooth and

Aux In.

8. 1/8” AUX IN - Connect a line level

device using a 3.5mm audio

cable.

9. XPD WIRELESS Input - Connect a

Samson XPD digital wireless USB receiver to this input.

10. MIX OUT - Male XLR connector used to link multiple RS Loudspeaker cabinets.

11. SIGNAL / LIMIT Indicator - This indicator lights green when signal is present. It will light red

when the amp is near the clipping point and the limiter is engaged.

12. POWER Indicator - This LED lights GREEN when amp is active.

13. POWER Switch - Switches on the RS Loudspeaker’s main power.

14. AC Power Inlet - Connect the supplied standard IEC AC power cable here.

15. Fuse Holder - The fuse holder comes from the factory with the appropriately rated fuse for

your model. If you need to change this fuse for any reason, replace it with one that has the

same exact rating.

Rear Panel Layout

USE ONLY WITHA 250V FUSE

EMPLOYER UNIQUEMENT

AVECUN FUSIBLE DE 205V

220–240

110–120

411

ENGLISHFRANÇAISDEUTSCHEESPAÑOLITALIANO

Quick Start

The following steps will help you get started using your RS Series Loudspeaker with a mixer.

1. Turn the RS Loudspeaker and mixer Power switch to the OFF positions.

2. Turn the VOLUME control on the rear panel of the RS Loudspeaker down, fully

counterclockwise.

3. Following the manufacturer’s instruction, connect your audio sources to your mixer.

4. Connect either a XLR or 1/4” cable from the output of your mixer to the INPUT 1 jack on

the RS Loudspeaker rear panel. Set the LINE/MIC switch to the LINE position.

5. Connect the supplied power cable to the IEC socket on the back of the loudspeaker. Plug

the power cable into an AC outlet.

Note: Always make sure that the AC outlet is configured with the correct voltage as

indicated on the rear panel of the RS Loudspeaker.

6. Turn on the power to the mixer and RS Loudspeaker(s).

7. Run an audio signal from your mixer and check that you are getting a good level using the

mixers output meter.

8. Slowly raise the RS Loudspeaker’s VOLUME control until you have reached the desired level.

9. If the volume from the speakers gets really loud, or you see the Limit indicator blinking

frequently, turn down the VOLUME control on the RS Loudspeaker a little until the

indicator does not light, or only lights occasionally with signal peaks.

Note: Before plugging in and turning on, remember the “last on, first

off” rule of powered audio gear - When powering up your system, be

sure that all the wires are connected, first turn on your mixer and

any other outboard gear, then turn on your RS Loudspeakers. When

powering down, turn off your RS Loudspeakers off first and then your

mixer and outboard gear.

7RS Active Loudspeakers with Bluetooth®

Follow these steps to connect a microphone level signal to your RS Loudspeaker and daisy-

chain the signal to a second RS Loudspeaker:

1. Set both RS Loudspeaker’s POWER switch to the OFF position.

2. Turn the VOLUME control down, fully counterclockwise.

3. Connect the power cables for each cabinet to an AC socket.

4. Connect a standard XLR cable from the main RS Loudspeaker’s MIX OUT to the second

RS Loudspeaker’s INPUT 1 XLR input.

5. On the second RS Loudspeaker, set the SENSITIVITY switch to the LINE position.

6. Using a standard XLR cable, plug a dynamic microphone into the RS Loudspeaker’s XLR

INPUT.

7. Set the SENSITIVITY switch to the MIC position.

8. Switch the Power switch to the ON position.

9. While speaking or singing into the microphone, slowly raise the VOLUME control until you

have reached the desired level.

10. For larger sound reinforcement you can run several monitors using the Mix Output to daisy-

chain one RS Loudspeaker to another. Set the input Sensitivity on the additional cabinets

to the LINE level position.

Connecting a Wired Microphone

ENGLISHFRANÇAISDEUTSCHEESPAÑOLITALIANO

1. Turn the BLUETOOTH/AUX IN Volume control

down counterclockwise to 0.

2. With the RS Loudspeaker and your Bluetooth

device powered on, quickly press and

release the Pair button on the rear panel of

the RS Loudspeaker to make the speaker

discoverable. The Bluetooth indicator will

slowly flash blue.

3. In the settings of your Bluetooth device, set it

to “discover” available devices.

4. From the Bluetooth device list, select the

“Samson BLUETOOTH” device.

5. If your device asks for a passkey, enter digits

0000 (four zeros) and press OK. Some

devices may also ask you to accept the

connection.

6. The RS Loudspeaker speaker indicates that pairing is complete when the indicator turns

steady blue. You can now stream audio from your device to the RS Loudspeaker.

7. With the volume control on your Bluetooth device turned up, play some music, and slowly

raise the RS Loudspeaker BLUETOOTH/AUX IN Volume control until you have reached the

desired level.

Following are step-by-step instructions

for changing the mains voltage of the RS

Loudspeaker.

WARNING: Before carrying out this operation,

remove the power cord!

1. Insert a small screwdriver into the slot

beneath the fuse sled and gently press

in and up. The fuse sled will pop out

approximately 3/8” inch.

2. Remove fuse sled.

3. Remove the fuse. Replace with the

correct fuse for your region.

4. Rotate the fuse sled and line up the

arrow on the AC inlet with the correct

voltage for your region.

5. Push the fuse sled into the AC inlet

until fully seated.

Bluetooth®Pairing

Voltage Selection Instructions

USE ONLY WITH A 250V FUSE

EMPLOYER UNIQUEMENT

AVECUN FUSIBLE DE 205V

220–240

110–120

USE ONLY WITH A 250V FUSE

EMPLOYER UNIQUEMENT

AVECUN FUSIBLE DE 205V

220–240

110–120

USE ONLY WITH A 250V FUSE

EMPLOYER UNIQUEMENT

AVECUN FUSIBLE DE 205V

220–240

110–120

USE ONLY WITH A 250V FUSE

EMPLOYER UNIQUEMENT

AVECUN FUSIBLE DE 205V

220–240

110–120

USE ONLY WITH A 250V FUSE

EMPLOYER UNIQUEMENT

AVECUN FUSIBLE DE 205V

220–240

110–120

9RS Active Loudspeakers with Bluetooth®

1. Plug the Samson XPD USB

receiver into the XPD Wireless USB

jack on the rear panel of the RS

Loudspeaker.

2. Turn the Bluetooth/Aux In Volume

knob on the RS Loudspeaker

completely counterclockwise.

3. Place a fresh set of AA (LR6)

batteries in the transmitter battery

holder, taking care to observe the

polarity markings, then replace the

cover.

4. Turn on the power to the transmitter

by pressing and holding Power

switch; the indicator light on the

transmitter and receiver will light

amber.

5. Speak or sing into the mic at a

normal performance level and raise

the Bluetooth/Aux In Volume control

until the desired level is reached.

Connecting XPD Wireless Microphone (sold separately)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Samson Sprecher Handbücher

Samson

Samson dB300a Bedienungsanleitung

Samson

Samson Sports S9HD Bedienungsanleitung

Samson

Samson Resolv A6 Bedienungsanleitung

Samson

Samson XP308i Bedienungsanleitung

Samson

Samson Studio Reference Monitor System Resolv 40a Bedienungsanleitung

Samson

Samson MediaOne 3a Bedienungsanleitung

Samson

Samson Expedition XP108W Bedienungsanleitung

Samson

Samson MEDIAONE BT Bedienungsanleitung

Samson

Samson PORTABLE PA SYSTEM EXL250 Bedienungsanleitung

Samson

Samson Expedition XP800 Bedienungsanleitung

Samson

Samson Expedition Express Bedienungsanleitung

Samson

Samson expedition xp1000 Bedienungsanleitung

Samson

Samson Expedition XP800 Bedienungsanleitung

Samson

Samson AURO D412 Bedienungsanleitung

Samson

Samson Rubicon R8a Bedienungsanleitung

Samson

Samson Expedition XP106 Bedienungsanleitung

Samson

Samson Expedition EX30 Bedienungsanleitung

Samson

Samson 215XL Bedienungsanleitung

Samson

Samson Resolv 50a Bedienungsanleitung

Samson

Samson Expedition EX10 Bedienungsanleitung

Samson

Samson AURO D415 Bedienungsanleitung

Samson

Samson Studio GT Bedienungsanleitung

Samson

Samson Resolv RXA5 Bedienungsanleitung

Samson

Samson EXPEDITION XP312w Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung