Samson MEDIAONE BT Bedienungsanleitung

OWNER'S MANUAL

If you want to dispose this product, do not mix it with general household waste. There is a separate

collection system for used electronic products in accordance with legislation that requires proper

treatment, recovery and recycling.

Private household in the 27 member states of the EU, in Switzerland and Norway may return their used electronic

products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).

For Countries not mentioned above, please contact your local authorities for a correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling

and thus prevent potential negative effects on the environment and human health.

AVIS

RISQUE DE CHOC ÉLECTRONIQUE -

NE PAS OUVRIR

This lightning ﬂash with arrowhead symbol within an equilateral triangle is intended to alert

the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure

that may be of sufﬁcient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance instructions in the literature accompanying

the appliance.

WARNING: To reduce the risk of electric shock, do not expose this apparatus to rain or moisture, do not remove

cover (or back) as there are no user-serviceable parts inside. Refer to servicing to qualiﬁed service personnel.

Federal Communication Commission Interference Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device accept any interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no gaurantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an

unctrolled environment. This equipment should be installed and operated within a minimum distance of 20cm

between the radiator and your body.

Caution: Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjuction with

any other antenna or transmitter. That separate approval is required for all other operating conﬁgurations, including

portable conﬁgurations with respect to Part 2. 1093 and different antenna conﬁgurations.

Important Safety Information

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near

water.

6. Clean only with dry cloth.

7. Do not block any ventilation

openings. Install in accordance with

the manufacturer’s instructions.

8. Do not install near any heat sources

such as radiators, heat registers,

stoves, or other apparatus (including

ampliﬁers) that produce heat.

9. Do not defeat the safety purpose

of the polarized or grounding type

plug. A polarized plug has two

blades with one wider than the

other. A grounding type plug has two

blades and a third grounding prong.

The wide blade or the third prong

are provided for your safety. If the

provided plug does not ﬁt into your

outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being

walked on or pinched particularly at

the plugs, convenience receptacles,

and at the point where they exit

from the apparatus.

11. Only use attachments/accessories

speciﬁed by the manufacturer.

12. Use only with the cart, stand,

tripod, bracket, or table speciﬁed

by the manufacturer, or sold with

the apparatus. When a cart is used,

use caution when moving the cart/

apparatus combination to avoid

injury from tip-over.

13. Unplug the apparatus during

lightning storms or when unused for

long periods of time.

14. Refer all servicing to qualiﬁed

personnel. Servicing is required

when the apparatus has been

damaged in any way, such as power

supply cord or plug is damaged,

liquid has been spilled or objects

have fallen into the apparatus has

been exposed to rain or moisture,

does not operate normally, or has

been dropped.

15. The apparatus shall not be exposed

to dripping or splashing and that

objects ﬁlled with liquids, such

as vases, shall not be placed on

apparatus.

16. Caution-to prevent electric shock,

match wide blade plug wide slot

fully insert.

17. Please keep a good ventilation

environment around the entire unit.

18. The use of apparatus in moderate

climates

19. WARNING: The mains plug/

appliance coupler is used as

disconnect device, the disconnect

device shall remain readily operable.

20. This equipment is a Class

II or double insulated electrical

appliance. It has been designed in

such a way that it does not require a

safety connection to electrical earth.

21. No naked ﬂame sources, such as

lighted candles, should be placed

on the apparatus.

Important Safety Information

Thank you for purchasing the MediaOne BT Powered Studio Monitors with Bluetooth from

Samson.

Samson MediaOne M30BT and M50BT Powered Studio Monitors Provide every musician

and content creator with reliable, full-range sound. Featuring loads of power, these

compact speakers bring excellent sound to any personal audio environment for gamers,

music enthusiasts, online conferencing and more. Bluetooth technology adds the

convenience of wireless audio streaming from any tablet, laptop, smartphone or other

enabled source.

The full-range Samson MediaOne BT Powered Studio Monitors deliver a big sound that

is perfectly balanced. The onboard Class AB amplifier pushes out power per with plenty

of headroom. Lightweight woven carbon fiber woofers with butyl surrounds, and tuned

cabinet-porting keep the bass tight and punchy. The switchable Bass Boost circuit fattens

up the low end even more. Silk-dome 3/4” tweeters create a clear, crisp, high-end sound

that’s never harsh. Custom waveguides ensure smooth highs and create a broader target

listening area.

In the box, you’ll find a registration card enclosed—please don’t forget to follow the

instructions so that you can receive online technical support and so we can send you

updated information about this and other Samson products in the future. We recommend

you keep the following records for reference, as well as a copy of your sales receipt.

Serial number: ____________________________________________

Date of purchase: __________________________________________

Dealer name: _____________________________________________

If you have any questions or comments regarding the MediaOne BT System or any other

products from Samson, do no hesitate to contact us at [email protected].

With proper care and maintenance, your MediaOne BT Powered Studio Monitors will operate

trouble-free for many years. Should your MediaOne BT ever require servicing, a Return

Authorization (RA) number must be obtained before shipping your unit to Samson. Without this

number, the unit will not be accepted. Please visit www.samsontech.com/ra for an RA number

prior to shipping your unit. Please retain the original packing materials and, if possible, return

the unit in its original carton. If your MediaOne BT was purchased outside of the United States,

contact your local distributor for warranty details and service information.

Introduction

• 20 watts (M30BT) or 80 watts (M50BT) of studio quality sound

• 3” (M30BT) or 5” (M50BT) woven carbon fiber woofers

• 3/4" silk dome tweeters

• Crystal clear high-end performance

• Exceptional bass responser

• Stereo RCA inputs

• Bluetooth Audio streaming

• Bass boost switch

• Headphone output mutes speakers

• Stereo 1/8” Sub output

• Speaker cable included

Features

The MediaOne BT main input connections can be made via the rear panel RCA inputs.

Follow the simple steps and diagram below for connecting an audio source to the speakers.

1. Connect the left and right speakers using the included two-conductor 1/8” (3.5mm)

speaker cable.

2. Turn the MediaOne BT Volume control completely counter-clockwise until it clicks to

the minimum/off setting.

3. Connect the MediaOne BT to an AC power outlet using the included power cable.

4. Connect the audio output from your audio source such as a computer or portable

audio device to the RCA inputs of the MediaOne BT right side speaker.

5. Turn the Volume control clockwise until it clicks to turn the MediaOne BT speakers

on. The front panel Power Indicator will light white.

6. Play music from your audio source and slowly raise the volume of the MediaOne BT

to a comfortable listening level.

Note: Before plugging in and turning on, remember the “last on, first off” rule of powered

speakers. When powering up your system, be sure that all the wires are connected, turn

your mixer and any other outboard gear on, and then last turn on your MediaOne M30.

When powering down, turn your MediaOne BT off first and then your mixer and outboard

gear.

Standby Mode

In order to save power, the MediaOne BT speakers will go into Standby mode when no

signal is present at any time for longer than 30 minutes. The front panel Power Indicator

will turn off, even with Power Switch in the On position. The speakers will automatically

wake up when you pass signal through the inputs.

Quick Start

Adding an Active Subwoofer

Adding a subwoofer to extend the low

frequency response of your monitor system

can be beneficial when mixing your music.

Typically, it is best to set the subwoofer level

to be equal to that of the main speakers.

Because deep-bass frequencies are non-

directional, it is difficult for our ears to

locate the sound source, and the precise

placement of the subwoofer is not as critical

as the main speakers. The ideal location

is between the two main speakers. If you

notice there are frequencies that sound

quieter than others, move the subwoofer

slightly to the left or right.

To add a powered subwoofer to your MediaOne BT speakers to create a 2.1 system:

• Connect your audio source to the left and right RCA Inputs of the MediaOne BT.

• Connect the MediaOne BT 1/8” STEREO / SUB Output to the left and right line

inputs of your active subwoofer.

• Play music from your audio source.

• Turn up your MediaOne BT to your desired listening level.

• Turn up the level of the subwoofer to desired level.

Note: The MediaOne BT front panel Volume control will control the level of the entire system.

SUBWOOFER

From Audio Source

A major objective when setting up your studio monitors is to obtain the best possible stereo

image. The MediaOne BT monitors are designed to be used in a vertical position, with the

tweeter and woofer symmetrically in line. Do not place these speakers horizontally as this

will cause an offset in sound between the woofer and the tweeter, limiting your ability to

find optimal listening positions.

Near field (close to the listener) monitoring has become the choice of many engineers

because of the cost and complexities associated with mounting monitors onto a wall.

Positioning your studio monitors correctly is very important. Correct placement not only

creates the proper stereo image, but also minimizes the effects of your room’s reflections.

This is especially important in today’s project studios, which are often multi-use spaces. By

taking some time and listening carefully when setting up your monitors, you can create an

optimal listening environment.

The most important consideration when evaluating room acoustics is the presence of

reflective surfaces near the monitoring area. These can include flat tabletops, glass mirrors

or framed pictures, large open walls and even the surface of your mixing console. Most

reflecting sound will eventually reach the listening position, but since it is slightly delayed

from the direct source, the result is random cancellation of some frequencies, or comb

filtering. If possible, remove any and all reflective surfaces. You may also want to hang

some acoustic foam on walls near the monitors.

When positioning the monitors, you’ll want to set up what is commonly referred to as

the “mix triangle” (shown below). In this ideal configuration, the space between the left

and right monitor is equal to the distance from the listener to each monitor, forming an

equilateral triangle.

Positioning the Speakers Having Trouble with your MediaOne Monitor Speakers?

We can help!

CONTACT OUR SUPPORT TEAM: [email protected]

Our experts can help you resolve any issues.

Having Trouble with your MediaOne Monitor Speakers?

We can help!

CONTACT OUR SUPPORT TEAM: [email protected]

Our experts can help you resolve any issues.

@samson @samsontech @samson_technologies

Low Frequency Speakers

High Frequency Speakers

Frequency response

Amplifier Power Rating

Distortion (T.H.D.)

Signal-To-Noise

Input Connectors

Headphone

Stereo / Sub Output

Bluetooth

Controls

Indicators

Enclosure

Dimensions (LxWxH)

Weight

3” (76.2mm) woofer, woven carbon fiber with

butyl surround

3/4” silk dome tweeter

50Hz - 20kHz (-2dB)

2 x 10 watts

<0.1%

83dB

RCA (rear panel)

1/8” (3.5mm) Stereo Output

1/8” (3.5mm)

V5.1+BR+EDR

Power / Volume Knob, Bass Boost Switch

White (Power), Blue (Paired)

MDF with textured vinyl covering

5” x 6.5” x 7.48”

127mm x 165mm x 190mm

6.61 lb

3 kg

Specifications - M30BT

Andere Handbücher für MEDIAONE BT

Inhaltsverzeichnis

Andere Samson Sprecher Handbücher

Samson

Samson Resolv A5 Bedienungsanleitung

Samson

Samson RS112A Bedienungsanleitung

Samson

Samson EXPIDETION XP25I Bedienungsanleitung

Samson

Samson Expedition XP310w Bedienungsanleitung

Samson

Samson Resolv RXA5 Bedienungsanleitung

Samson

Samson Expedition XP300 Bedienungsanleitung

Samson

Samson STUDIOGT Bedienungsanleitung

Samson

Samson AURO D412 Bedienungsanleitung

Samson

Samson MEDIAONE BT3 Bedienungsanleitung

Samson

Samson Resolv 50a Bedienungsanleitung

Samson

Samson Expedition Express Bedienungsanleitung

Samson

Samson Expedition Escape Bedienungsanleitung

Samson

Samson Auro D208 Bedienungsanleitung

Samson

Samson RL112A Bedienungsanleitung

Samson

Samson dB300 Bedienungsanleitung

Samson

Samson AURO D415 Bedienungsanleitung

Samson

Samson Expedition XP300 Bedienungsanleitung

Samson

Samson EXPEDITION XP150 Bedienungsanleitung

Samson

Samson RS Series Bedienungsanleitung

Samson

Samson Expedition EX10 Bedienungsanleitung

Samson

Samson RSX115 Bedienungsanleitung

Samson

Samson RESOLV5e Bedienungsanleitung

Samson

Samson XP308i Bedienungsanleitung

Samson

Samson Studio Reference Monitor System Resolv 40a Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung