Samsung MOS-C1 Bedienungsanleitung

INSTALLATION

MANUAL

MOS-C1

DB98-29348A(1)E

ERV

(Energy Recovery Ventilator)

MOS-C1_IM_E_29348-1.indd 17 2008-01-31 ｿﾀﾈﾄ 3:57:19

WARNING

Risk of death or serious personal

injury.

CAUTION

Potential risk of personal injury or

material damage.

WARNING

Please contact the Service

Center for installation.

 Improper installation may cause

damage to the product, water

leakage, electric shock, or fire.

Always use rated voltage.

 Improper voltage may cause

damage to the product and/or

fire.

Check if the product

is properly installed in

accordance with the manual.

 Improper installation may cause

electric shock or fire.

Do not disassemble or

modify any part of the

product.

Contact the Service Center for

maintenance to prevent product

malfunction, electric shock and

fire.

Contact a qualified technician

for reinstallation or transfer of

a unit.

 Potential risk of electric shock or

fire.

All electrical maintenance

should be performed by

a qualified technician in

accordance with local

regulations and instruction

manuals.

 Improper handling of the

product may cause damage to

the product or fire.

This information is provided to prevent personal injury and material damage.

Please read all safety information before use

SAFETY INFORMATION

MOS-C1_IM_E_29348-1.indd 2 2008-01-31 ｿﾀﾈﾄ 3:57:01

 SAFETY INFORMATION (Continued)

CAUTION

Do not expose the product to

excessive heat or flammable

sources

Potential risk of fire hazard or

explosion.

Install the product in a place

without moisture.

 Moisture may cause damage to

the product and electric shock.

Use only rated parts for

installation.

 Potential risk of electric shock or

fire.

Electric wiring should be

properly connected and

fixed.

 Potential risk of fire hazard or

explosion.

Avoid tension on electric wires.

 Wires may break and cause fire.

Ensure proper ground has

been established when

installing the product. Do not

connect the ground cable of

the unit to a gas pipe, a water

pipe or a telephone line.

 Potential risk of electric shock.

Ensure no water gets into the

product.

 Potential risk of electric shock or

fire.

Disconnect the product

from power supply during

maintenance.

 Potential risk of electric shock.

MOS-C1_IM_E_29348-1.indd 3 2008-01-31 ｿﾀﾈﾄ 3:57:02

INSTALLATION OF CO2 SENSOR

Parts

CO2 Sensor

QTY

Image

Instructions

Applicable Models: RHF025EE

2) Unscrew the three bolts from the

maintenance cover.

1) Turn off the power and

disconnect the product from

power supply.

Back

Front

Top

Bolt

3) Unhook the clip from the

maintenance cover.

Clip

Cable Bolt Cable Tie INSU Installation

manual

11111

MOS-C1_IM_E_29348-1.indd 4 2008-01-31 ｿﾀﾈﾄ 3:57:04

 INSTALLATION OF CO2 SENSOR (Continued)

4) Disengage the connector attached

to the damper for ventilation

switch.

 Pull the body part outward to

disengage the connector.

B-Part

A-Part

5) Unscrew the four bolts and

disengage the B-Part of the

bracket body element from the

product.

6) Pull up the strings to disengage

the heat exchange from the

product.

7) Unscrew the four bolts and

disengage the A-Part of the

bracket body element from the

product.

8) Pull the cushion bypass to

disengage it form the product

as illustrated.

MOS-C1_IM_E_29348-1.indd 5 2008-01-31 ｿﾀﾈﾄ 3:57:06

9) Attach the INSU to a place where

CO2 Sensor is to be positioned.

10) Position the CO2 Sensor onto the

hole and secure in place with a

bolt.

 It is connected to the RA duct.

11) Secure the cable to the two

cable holders using cable ties.

12) Take out the connector together

with the cable through the cable

outlet.

13) Connect the connector to the

CO2 Sensor as illustrated.

INSU

CO2

Sensor

Bolt

Cable Tie

Cable

Outlet

 INSTALLATION OF CO2 SENSOR (Continued)

MOS-C1_IM_E_29348-1.indd 6 2008-01-31 ｿﾀﾈﾄ 3:57:07

1) Turn off the power and

disconnect the product from

power supply.

 It is not necessary to disassemble

the product to replace or clean

the fan, motor, heat exchange

unit, or dust filter.

2) Unscrew the two bolts from

the maintenance cover and

disengage them from the hook.

 After disengaging the maintenance

cover, check 2 heat exchange units

and 2 dust filters.

 All work should be carried out

through the maintenance opening

from this point.

3) Disengage the heat exchange

units and dust filters from the

product.

 Make sure to disengage the

filters first.

 Both heat exchange units should

be disengaged from the product.

4) Unscrew the bolt and

disengage the heat exchange

unit guide on the right side from

the product.

Instructions

 Applicable Models: RHF 035EE/RHF050EE/RHF080EE/RHF100EE

Back

Front

Top

Bolt

Heat Exchange Unit

Dust Filter

Heat Exchange Unit

 INSTALLATION OF CO2 SENSOR (Continued)

MOS-C1_IM_E_29348-1.indd 7 2008-01-31 ｿﾀﾈﾄ 3:57:08

5) Unscrew the four bolts and

remove the electric system cover.

6) Position the INSU in the hole

located on the right side of the

damper.

7) Connect the white terminal of the

cable to the CO2 Sensor.

8) Position the CO2 Sensor onto the

hole and secure in place with a

bolt.

Bolt

INSU

CO2

Sensor

Bolt

 INSTALLATION OF CO2 SENSOR (Continued)

MOS-C1_IM_E_29348-1.indd 8 2008-01-31 ｿﾀﾈﾄ 3:57:09

10) Take out the CO2 Sensor cable

together with other cables and

reassemble the guide filter.

11) Take out the CO2 Sensor cable

together with other cables

through the outlet located on

the PCB board.

12) Connect the connector to the

CO2 Sensor as illustrated.

 Reassemble in reverse order of

disassembly

9) Secure the cable to the two

holders using cable ties. Cable Tie

Guide Filter

 INSTALLATION OF CO2 SENSOR (Continued)

MOS-C1_IM_E_29348-1.indd 9 2008-01-31 ｿﾀﾈﾄ 3:57:10

INSTALLATION OF PCB OPTION

Configuration of CO2 Sensor

 Switch off the K9 of SW06 in the MAIN PCB to set the CO2 Sensor to “Use” mode.

K9 K10 K11 K12

Checking Operation after Power-on

1) Check if LED1 flashes once every 6 seconds or so.

LED1

MOS-C1_IM_E_29348-1.indd 10 2008-01-31 ｿﾀﾈﾄ 3:57:16

Andere Handbücher für MOS-C1

Inhaltsverzeichnis

Andere Samsung Controller Handbücher

Samsung

Samsung WEC8500 Bedienungsanleitung

Samsung

Samsung MWR-WG00JN Bedienungsanleitung

Samsung

Samsung SCC-3000 Bedienungsanleitung

Samsung

Samsung MCM-A00N Bedienungsanleitung

Samsung

Samsung SCC-3100 Bedienungsanleitung

Samsung

Samsung SCC-3100A Bedienungsanleitung

Samsung

Samsung SPC-2000 Bedienungsanleitung

Samsung

Samsung ET-YO324 Bedienungsanleitung

Samsung

Samsung SCC-1000 Bedienungsanleitung

Samsung

Samsung SPC-7000 Bedienungsanleitung

Samsung

Samsung Function controller Bedienungsanleitung

Samsung

Samsung SCC-101 Bedienungsanleitung

Samsung

Samsung TracFone SGH-T330G Bedienungsanleitung

Samsung

Samsung SPC-1010 Bedienungsanleitung

Samsung

Samsung MCM-A200 User Manual (XP) Bedienungsanleitung

Samsung

Samsung MCM-C210 Bedienungsanleitung

Samsung

Samsung AC0 JNHDCH/AA Series Service-Handbuch

Samsung

Samsung WEC8500 Bedienungsanleitung

Samsung

Samsung 136S Bedienungsanleitung

Samsung

Samsung MCM-A202DN Bedienungsanleitung

Samsung

Samsung RMC30D1 Bedienungsanleitung

Samsung

Samsung MCM-A100 Bedienungsanleitung

Samsung

Samsung SM-N9109W Bedienungsanleitung

Samsung

Samsung HARMAN AMX MU Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch