Santon EV 2008 Leitfaden

MULTIPOINT

Installation and User Instructions

Instantaneous Hand Wash

Models: EV 2008 No-Touch

Please read and understand these instructions before starting work.

Please leave this leaet with the user following installation

PACK CONTENTS

Heater, Spout assembly, Fixing screws and plugs,

Torx adjusting tool,

Installation and User Instructions.

WARNING

This Instantaneous Hand Wash must only be installed

by qualied persons.

36006007 Issue 4.

EV 2008 No Touch

Thank you for purchasing a Santon EV2008 Hand wash. The Hand wash instan-

taneous water heater is manufactured to the highest standards and has been

designed to meet all the latest relevant safety specications.

This Hand wash instantaneous water heater must be installed (Sections 4.0-7.0),

commissioned (Section 7.0) and maintained (Sections 8.0 - 9.0) by a competent

person. Please read and understand these instructions prior to installing your

Hand wash instantaneous water heater. Particular attention should be paid to the

section headed SAFETY (section 2.0). Following installation and commissioning

the operation of the heater should be explained to the user (Section 7.0) and these

instructions left with them for future reference.

This appliance can be used by children aged from 8 years and

above and persons with reduced physical sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervison or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

Children must be supervised to ensure they do not play with the

appliance.

CONNECTIONS

Inlet connection -15mm ext. diameter (copper or push t stem elbow)

Water entry point - bottom and rear

Cable entry point - bottom and rear

ELECTRICAL

Model numbers

3.1kW - Hand wash - 94 020 017

Electrical rating....................................................................2.9/3.1kW @ 230/240V

Ampre rating.......................................................................2.9/3.1kW @12.4/12.9A

MATERIALS

Backplate, cover and control knob- ABS

Element(s) - Copper sheathed rod type.

DIMENSIONS

Height - 235mm

Width - 151mm

Depth - 85mm

STANDARDS AND APPROVALS

Complies with the requirement of EN 60335-2-35.

Complies with European Community Directives (CE).

Complies with uk water regulations, kiwa approved.

TECHNICAL SPECIFICATION

INTRODUCTION

MULTIPOINT

1.1 A pressure relief device (PRD) is designed into the hand wash

appliance, which complies with European standards. The PRD

provides a level of appliance protection should an excessive build-up

of pressure occur within the appliance.

1.2 DO NOT operate the hand wash with a damaged spout or blocked

sprayplate, which can cause the PRD to operate.

IMPORTANT INFORMATION

2.1 Products manufactured by Santon are to British and European

Standards. These appliances are safe and without risk, provided

they are installed, used and maintained in good working

order in accordance with our instructions and recommendations.

2.2 Please read and understand these instructions before starting work

and retain them for later use.

2.3 DO NOT operate the appliance if it is frozen, or suspected of being

frozen. See fault nding table.

2.0 SAFETY

1.0 INTERNAL COMPONENTS

Thermal

cut-out

Front

cover

Inner

container

Pressure switch

Terminal block

Cable clamp

Pressure relief device (PRD)

Spout fixing nut

Outlet spout

Sprayplate

Figure 1 Internal components - 3.1kW

Thermostat

Rating Label

Solenoid valve

Flow control valve

2.4 DO NOT operate the appliance if:

1. Water ceases to ow during use.

2. Water has entered inside the unit because of an incorrectly tted

cover.

3. If the appliance is damaged.

2.5 ISOLATE the electrical and water supplies before removing the cover.

2.6 ISOLATE the electrical and water supplies BEFORE proceeding with

installation or servicing.

2.7 The appliance must be mounted on to a at nished wall surface that

covers the full width and length of the backplate (or on top of the tiles).

2.8 DO NOT tile up to the appliance after xing to the wall.

2.9 The sprayplate must be cleaned when any of its holes become blocked,

otherwise restriction to the ow from the outlet spout will result in

higher temperatures and could also cause the pressure relief device in

the appliance to operate - see 1.1 and 9.2.

2.10 The product is NOT SUITABLE for mounting into steam rooms or

steam cubicles.

2.11 The installation must be carried out in accordance with the relevant

requirements of:

• The appropriate Building Regulations either The Building Regulations,

The Building Regulations (Scotland) or Building Regulations (North

ern Ireland).

• The Water Fittings Regulations or Water Byelaws in Scotland.

CAUTION

2.12 It is recommended that persons who may have difculty understanding

or operating the controls should not be left unattended whilst washing

hands. Special consideration should be given to young children and

persons with reduced physical, sensory or mental capabilities.

2.13 Only use designated entry points for cable and pipe.

PLUMBING

2.14 The plumbing installation must comply with Water Regulations.

2.15 The supply pipe must be ushed to clear debris before connecting to

the hand wash appliance.

2.16 DO NOT solder pipes or ttings within 300mm once the pipework is

located in the appliance, as heat transfer can damage components.

2.17 DO NOT t any form of outlet ow control, as the outlet acts as a vent

for the heater can.

2.18 DO NOT use excessive force when tting the spout xing nut, nger

tightness is sufcient.

2.19 All plumbing connections must be completed and checked for leaks

before making the electrical connections.

MULTIPOINT

ELECTRICAL

2.20 Before tting the appliance, ensure that the consumer unit and any

switches are suitable for the additional load. If in doubt, contact your

electricity supplier or a qualied electrician.

2.21 The installation must comply with BS 7671 ‘Requirements for

electrical installations’ (IEE Wiring Regulations).

CAUTION

2.22 This appliance must be earthed.

2.23 Fuses do not give personal protection against electric shock. To

enhance electrical safety a 30mA residual current device (RCD)

should be installed in all electric hand wash circuits. This may be

part of the consumer unit, or a separate unit.

2.24 Ensure that all terminal block connections are sufciently tight.

2.25 Switch off appliance immediately and isolate if water ceases to ow

during use.

2.26 Other electrical equipment e.g. extractor fans, must not be

connected to the hand wash or its supply circuit.

Supplier’s name or trade mark Santon

Supplier’s model identier EV 2008 No-Touch

The declared load prole XXS

The water heating energy efciency class of the model A

The water heating energy efciency in % 38.6

The annual electricity consumption in kWh 478

Daily fuel consumption in kWh 2.200

Specic precautions that shall be taken when the water

heater is assembled, installed or maintained and disposed

of at end of life

See Section 1 to 7

Table: Technical parameters in accordance with European Commission regulations

814/2013 and 812/2013

WARNING

3.1 The hand wash must not be positioned where it will be subjected to

freezing conditions.

WATER REQUIREMENTS

3.2 The installation must be in accordance with Water Regulations. To

ensure activation of the heating elements, the hand wash must

be connected to a mains water supply with a minimum running

pressure of 0.1 MPa (1 bar) and a maximum static pressure of 0.7 MPa

(7 bar). If static pressure exceeds 0.7MPa (7bar) t a pressure reducing

valve to avoid damaging the appliance. If in doubt, the pressure should

be checked taking account of other services from the same water

supply which could cause the pressure to fall below the minimum. The

water supply can also be taken from a cold water storage cistern

provided there is a minimum head of 10m above the appliance.

3.3 If the hand wash is operated outside of the stated pressure parameters, it

may not be possible to achieve optimum performance from the

appliance throughout the year.

ELECTRICAL REQUIREMENTS

WARNING

3.0 SITE REQUIREMENTS

red

Cut

Out

red

black

red

green/yellow

Inner

container

Pressure

switch

Terminal

block

3.1kW

Figure 2 Wiring diagram

black

Neon

black

red

Solenoid

valve

PCB Infra-red

{

Solenoid

PCB

MULTIPOINT

3.4 The appliance must be earthed

IMPORTANT - INSTALLATION TO BE DONE BY A COMPETENT

INSTALLER

3.5 The installation supply cable and circuit protection must conform to

BS 7671.

3.6 Before making any sort of electrical connection, ensure that no terminal

within the circuit is live. If in any doubt SWITCH OFF the whole

installation at the consumer unit.

3.7 The hand wash must only be connected to a 230-240V ac supply.

3.8 The earthing and protective conductor arrangement within the

property, in particular the supplementary bonding in the room

containing the hand wash, must comply with BS 7671.

3.9 Ensure that the supply cable and fuse are sufcient for the rated input of

your appliance. Please refer to the rating label within the appliance.

3.10 For a 3.1kW unit:

A minimum heat resistant cable size of 1.5mm² should be used. The

hand wash can be connected in two different ways.

1. Via a fused and switched connection unit taken as a spur

from a 13amp ring main.

2. As a separate circuit taken directly from a spare way in a consumer

unit.

In each case a double pole isolating switch having a contact separation

of at least 3mm in each pole, and a minimum rating of 13amp must be

incorporated in the wiring of the appliance.

Figure 3 Schematic of typical electrical layout

Hand wash unit

(use rear entry when it is

possible)

800 or 100A main switch

Meter

Meter ‘tails’

Consumer unit

RCD (can be part of the

consumer unit)

Double pole isolating switch:

pull cord or wall mounted in accordance

with IEE regulations

3.11 To obtain full advantage of the power provided by the hand wash, use

the shortest cable route possible from the consumer unit to the hand

wash.

3.12 If your consumer unit has a rating below 80A or, if there is no spare fuse

way, then the installation will not be straightforward and may require a

new consumer unit. A qualied electrician should install the new

consumer unit. It may be necessary to contact your electrical supplier to

upgrade your supply.

CAUTION

3.13 To enhance electrical safety a 30mA residual current device (RCD)

should be installed in all electric hand wash circuits. This may be part

of the consumer unit or a separate unit. DO NOT use a rewireable fuse,

instead use a suitably rated miniature circuit breaker (MCB) or cartridge

fuse. The hand wash must be connected to its own independent

electrical circuit.

MULTIPOINT

IMPORTANT - INSTALLATION TO BE CARRIED OUT BY A COMPETENT

INSTALLER

4.1 The appliance must be mounted on a at surface, which covers the full

width and length of the backplate. It is important that the wall surface

is at otherwise difculty may be encountered when tting the cover.

4.2 Ensure that the hand wash is positioned over the basin, because if the

PRD operates water will eject from the bottom of the appliance.

4.3 The outlet of the hand wash acts as a vent and MUST NOT be connected

to any form of outlet ow control, or any other tting not recommended

by Santon.

4.4 DO NOT t the hand wash to the wall and tile up to the case. It must

be tted on to a nished at and even wall surface. This allows removal

for servicing.

4.5 The control knob is an integral part of the cover - do not attempt to

remove it.

4.0 CONSIDERATIONS BEFORE FITTING

4.6 Position the unit above the

basin so that the spray will be

contained within the basin and at a

convenient height for hand

washing see Figure 4 opposite.

4.7 A clearance of at least 130mm

above and below the unit should

be allowed for access to the cover

screws.

4.8 Cable entry can be from the rear

(preferred) or from the bottom. The

backplate has cut-out position to

suit size of cable. When opting

for bottom entry make the cut-out

to suit the cable before tting the

backplate to the wall -see Figure

5 below.

Figure 4 Handwash position over basin (or sink)

200

PRD

Outlet

Typical arrangement

Isolating stop valve

Main water supply

(Use rear entry when

it is possible)

130mm

min

Make cut-out

using sharp

knife

Figure 5 Bottom entry cable cut-out

PIPE ENTRY

4.9 Plumbing entry can be from the rear (preferred) or from the bottom.

The backplate has a cut out position to suit 15mm pipe. When opting

for bottom entry make cut out before tting backplate to the wall -

see Figure 6 below.

5.1 TURN OFF water and electrical supply.

5.2 The appliance is designed for bottom and rear entries of water and

electric cable. It is advisable to use the rear entry (when it is

possible), in order to obtain a neater installation.

5.3 Unscrew the retaining screws and lift the cover from the back plate -

see Figure 7 below.

5.0 FITTING INSTRUCTIONS

5.4 Fit the outlet spout - DO NOT over tighten, nger tight will be sufcient

- see Figure 8 above.

5.5 After choosing the correct site for the hand wash, use the backplate as a

template and mark the two xing holes - see 4.1 to 4.7 p9.

BEWARE OF CABLES AND PIPES WHICH MAY BE BURIED IN THE

WALL.

5.6 Drill holes using a 6.5mm diameter masonry drill.

5.7 Use plugs to suit the wall and use the xing screws supplied.

Cable

Clamp

Inlet water

connection

Terminal

Block

Rear entry access

area for electricity and

inlet water supply

Figure 9 Unit layout - Dimensions (mm)

19.5

196.5

235

151

Figure 7 Removing Cover

Figure 8 Fitting outlet spout

'O' rings

Plastic nut

(finger tight only)

Outlet pipe

Make cut-out

using sharp knife

Figure 6 Plumbing cut-out

Andere Handbücher für EV 2008

Inhaltsverzeichnis

Andere Santon Boiler Handbücher

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

Applimo

Applimo Edel AIR Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung