Sanus Systems VMFL1 Bedienungsanleitung

Assembly Instructions for Model: VMFL1

Thank you for choosing a Sanus Systems Vision Mount wall mount. The VMFL1 is designed to mount up to 30” [76.2 cm] LCD at panel

televisions weighing up to 40 lbs [18 Kg] to a vertical wall. It will allow the television to be just 0.5” [12.7 mm] from the wall.

WARNING: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualied

contractor or contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective

parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement

parts for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Improper installation

may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specied by Sanus Systems. Sanus

Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus

Systems before returning products to the point of purchase.

Required Tools: 3/8 or 1/8 drill bit, phillips screwdriver

Supplied Parts and Hardware: (All threaded fasteners are shown full size.)

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.23.06 (000026)

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Wall Plate - A

Qty. 1

Monitor Bracket - B

Qty. 1

Lag Screw - C

Qty. 2

Dry Wall Anchor - D

Qty. 4

M4 x 10 mm Bolt - E

Qty. 4

M4 Washer - I

Qty. 4

Small M4 Spacer - J

Qty. 4

Large M4 Spacer - K

Qty. 4

M5 Spacer - L

Qty. 2

M4 x 20 mm Bolt - F

Qty. 4

M4 x 30 mm Bolt - G

Qty. 4

M5 Locking Bolt - H

Qty. 2

Step 1: Hang Wall Plate

NOTE: Make sure the Wall Plate (A) is oriented so the at surface in the center of the plate is against the wall as shown in

Diagram 1A.

Wood Stud Mounting:

Using a high quality stud sensor to locate a stud: then, using the Wall Plate (A) as a template mark two holes in the appropriate location,

making sure the hole is in the center area of the stud.

Pre-drill a 1/8” hole 2.5” [63.5 mm] deep where the upper Lag Screw (C) will be installed; then, secure the Wall Plate (A) to the stud using

one of the Lag Bolts as shown in Diagram 1A.

Verify that the Wall Plate is level; then pre-drill a 1/8” hole 2.5” [63.5 mm] deep for the lower Lag Screw (C) and secure the bottom of the

Wall Plate (A) with the second Lag Screw as shown in diagram 1A.

Drywall Installation:

Position the Wall Plate (A) in the desired location on the wall; then, use the Wall Plate as a template and mark the location of the four

outer mounting holes.

Using a 3/8”drill bit, proceed to drill a 3/8”pilot hole in each marked location.

Install a Dry Wall Anchor (D) in one of the pilot holes and tighten the Anchor Bolt until it is fully seated as shown in Diagram 1B.

NOTE: Make sure the Washer is between the head of the Anchor Bolt and the Wall Plate (A) as shown in Diagram 1C.

Loosen the Anchor Bolt approximately 1/4” and repeat the above process for the three additional pilot holes. Once Wall Plate (A) is

mounted onto the wall, verify that it is level; then, proceed to tighten all four Anchor Bolts.

Diagram 1A Diagram 1B Diagram 1C

Step 2: Install M5 Locking Bolts

Insert both M5 Locking Bolts (H) through a M5 Spacer (L); then, thread the M5 Locking Bolts into the Monitor Bracket (B) just enough to

engage the threads as shown in Diagram 2.

Diagram 2

Level

Drill 3/8”

Pilot Hole

Insert

Dry Wall

Anchor (D)

Tighten Bolt

Until Anchor

is against wall

Washer must

be between

Anchor Bolt

and

Wall Plate (A)

Step 3: Attach Monitor Bracket to at back TV

To attach the Monitor Bracket (B) to the TV, insert a M4 x 10 mm Bolt (E) through the countersunk hole in the Monitor Bracket, and the

M4 Washer (I); then, thread it into the TV. Repeat this until all four bolts are secured to the TV, as shown in Diagram 3. Tighten each

M4 x 10 mm Bolt with a phillips screw driver.

Diagram 3

Step 4: Attach Monitor Bracket to a TV with a recessed hole pattern

To attach the Monitor Bracket (B) to the TV, insert a M4 x 20 mm Bolt (F) through the countersunk hole in the Monitor Bracket, and the

Small M4 Spacer (J); then, thread it into the TV. Repeat this until all four bolts are secured to the TV as shown in Diagram 4. Tighten each

M4 x 20 mm Bolt with a phillips screw driver.

Diagram 4

Step 5: Attach Monitor Bracket to a TV with a deeply recessed hole pattern

To attach the Monitor Bracket (B) to the TV, insert a M4 x 30 mm Bolt (G) through the countersunk hole in the Monitor Bracket, and the

Large M4 Spacer (K); then, thread it into the TV. Repeat this until all four bolts are secured to the TV as shown in Diagram 5. Tighten each

M4 x 30 mm Bolt with a phillips screw driver.

Diagram 5

Step 6: Attach Monitor Bracket to Wall Plate

Lift the TV so the two hooks on the Monitor Bracket (B) align with the slots on the top of the Wall Plate (A) as shown in Diagram 6A.

Lower the TV so that the hooks on the top of the Monitor Bracket (B) drop into the slots on the Wall Plate (A) but the hooks on the bottom

are not engaged as shown in Diagram 6B.

Diagram 6A Diagram 6B

Step 7: Cable hook up and lock Monitor Bracket to Wall Plate

To allow for greater space between the wall and your display to install cables, allow the display to hang from the two top hooks on the

Monitor Bracket (B) with the bottom tabs free to move as shown in Diagram 7A.

Once all cables are installed, lift the TV just enough to engage the two lower hooks on the Monitor Bracket (B) with the slots in the Wall

Plate (A) as shown in detail 7B

Tighten both M5 Locking Bolts (H) to secure the Monitor Bracket (B) to the Wall Plate (A).

Diagram 7A Diagram 7B

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.23.06 (000026)

Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Andere Handbücher für VMFL1

Inhaltsverzeichnis

Andere Sanus Systems Rack & Stand Handbücher

Sanus Systems

Sanus Systems VMSA Bedienungsanleitung

Sanus Systems

Sanus Systems SD103 Bedienungsanleitung

Sanus Systems

Sanus Systems VisionMount VMA202 Bedienungsanleitung

Sanus Systems

Sanus Systems VisionMount ML22 Bedienungsanleitung

Sanus Systems

Sanus Systems WMS5 Bedienungsanleitung

Sanus Systems

Sanus Systems New VisionMount VMA201 Bedienungsanleitung

Sanus Systems

Sanus Systems Monitor Mount VMTV Bedienungsanleitung

Sanus Systems

Sanus Systems VMPR1 Bedienungsanleitung

Sanus Systems

Sanus Systems FM37 Bedienungsanleitung

Sanus Systems

Sanus Systems NEW FOUNDATIONS 500 Series Bedienungsanleitung

Sanus Systems

Sanus Systems BF16 Bedienungsanleitung

Sanus Systems

Sanus Systems VMCC1 Installationsanleitung

Sanus Systems

Sanus Systems VM2 Bedienungsanleitung

Sanus Systems

Sanus Systems Wall Mount LL22 Bedienungsanleitung

Sanus Systems

Sanus Systems Sanus VisionMount LRF118-B1 Bedienungsanleitung

Sanus Systems

Sanus Systems SANA1A Bedienungsanleitung

Sanus Systems

Sanus Systems VisionMount VMPL2 Bedienungsanleitung

Sanus Systems

Sanus Systems PFV60-B1 Bedienungsanleitung

Sanus Systems

Sanus Systems WMS2 Bedienungsanleitung

Sanus Systems

Sanus Systems HTSAT Bedienungsanleitung

Sanus Systems

Sanus Systems VISIONMOUNT VMCA8 Bedienungsanleitung

Sanus Systems

Sanus Systems VisionMount MF202 Bedienungsanleitung

Sanus Systems

Sanus Systems New VisionMount VMA201 Bedienungsanleitung

Sanus Systems

Sanus Systems VisionMount MF203 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung