Sanyo POA-CH-EX06 Bedienungsanleitung

Installation Manual

Setting Plate for Wall Hanging

Model POA-CH-EX06

Contents

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

List of Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Install the wall plate to the wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Attach the setting plate to the wall plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Securing the projector to the setting plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Attach the drop-prevention wire to the projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Projection Distance Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

This installation manual describes how to mount the projector to a wall using

the setting plate (model POA-CH-EX06).

This setting plate is only for use with Sanyo projectors mentioned below.

PDG-DWL2500, PDG-DXL2000 and other related models. (For details on available models,¡

please contact your nearest Sanyo dealer.)

Be sure to consult with a qualiﬁed installation specialist.

EnglishFrançaisEspañolDeutschItalianoPortuguês

日本語

POA-CH-EX06(IJAH).indbaPOA-CH-EX06(IJAH).indba 10.9.811:21:12AM10.9.811:21:12AM

■Explanation of Symbols

The warning marks shown below are used in this manual to prevent personal injury or property dam-

age. Make sure you understand these warnings when reading this installation manual.

WARNING This symbol indicates information that, if ignored,

could possibly result in personal injury or even

death due to incorrect handling.

CAUTION This symbol indicates information that, if ignored,

could possibly result in personal injury or physi-

cal damage due to incorrect handling.

This symbol indicates an action that must not be done.

This symbol indicates an action that should be done.

WARNING

This setting plate is only for use with speciﬁed Sanyo projector. Do not use for any other

equipment or purpose.

Never modify the setting plate.

Do not hang from the setting plate or hang heavy objects on the setting plate.

Be especially careful that children do not hang from it.

Do not install the setting plate in a place where it might be subjected to vibration or

shock.

Never loosen the screws, bolts or nuts after installation.

Do not use adhesives to prevent the screws loosening and do not use oils or lubricants

for moving parts.

If such substances are applied to the projector’s cabinet, the cabinet may crack and fall, causing

serious injury to people or serious damage to the projector.

Safety Instructions

POA-CH-EX06(IJAH).indb1POA-CH-EX06(IJAH).indb1 10.9.811:21:13AM10.9.811:21:13AM

English

CAUTION

Do not install the setting plate in a location where the operating temperature for your

projector model may be exceeded. Such an environment may damage the projector.

Install the setting plate in a place free from excessive dust and humidity to prevent the

lens or optical components of the projector from becoming dirty.

Safety Instructions

The installation work should be performed by at least two qualiﬁed service personnel.

If you need to loosen any screws during installation, be careful not to drop the setting

plate.

If mounting the projector on a wall with the setting plate, the wall must have enough

strength to hold the projector and setting plate. Conﬁrm the weight of the projector and

the setting plate before installation, and check the strength of the wall. If the wall is not

strong enough, reinforce the wall before installation.

Tighten all screws ﬁrmly after adjustment.

Inspect the setting plate on a regular basis to ensure there are no broken parts or loose

screws.

Install the setting plate to a vertical wall. Do not install to a leaning wall.

Do not install the setting plate in greasy or smoky place to prevent breakdown or abra-

sion of the projector’s components.

Do not install the setting plate in steamy, smoky or highly humid places in order to pre-

vent ﬁre or electric shock.

Do not use a setting plate with damaged parts. The projector or setting plate may fall and

cause personal injury or property damage.

POA-CH-EX06(IJAH).indb2POA-CH-EX06(IJAH).indb2 10.9.811:21:13AM10.9.811:21:13AM

List of Accessories

qWall plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

wSetting plate . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

eCover plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

rAdjustment unit . . . . . . . . . . . . . . . . . . . . . . . . 1

tHexagon wrenches . . . . 2 (3 mm...1, 6 mm...1)

yScrews M4 x 18 mm

(for securing projector and adjustment unit)

. . 5

uM8 x 20 mm hexagon socket head cap bolt

(for securing setting plate and wall plate) . . . 4

uyo

iM5 x 10 mm hexagon socket head cap bolt

(for securing cover plates) . . . . . . . . . . . . . . . 2

oStrap for binding cables . . . . . . . . . . . . . . . . . 2

!0 Drop-prevention wire. . . . . . . . . . . . . . . . . . . . 1

!1 Template sheet for installing the wall plate. . 1

!2 Installation Manual (this manual) . . . . . . . . . . 1

POA-CH-EX06(IJAH).indb3POA-CH-EX06(IJAH).indb3 10.9.811:21:13AM10.9.811:21:13AM

English

Installation Procedure

Install the wall plate to the wall

1Determine the position of the wall plate using the template sheet.

From the projection distance table (page 10) and dimensions (page 11), conﬁrm the screen size and the¡

distance between the projection surface and wall plate.

The wall plate and the projection surface have different vertical center lines.¡

Align the CTR line (printed on the template sheet) with the center line of the projection surface as shown in

the illustration.

Conﬁrm where the beams are within the wall,¡

and shift the position vertically or left and

right as necessary.

2Attach the template sheet to the wall.

3Make mounting holes in the wall in the required locations.

4Remove the template sheet.

5Mount the wall plate on the wall.

WARNING

When you install the projector to the wall with the setting plate, the wall needs to be¡

strong enough to hold the projector and the setting plate. Conﬁrm the weight of the pro-

jector and the setting plate before installation, and check the strength of the wall.

If the wall is not strong enough, reinforce the wall before installation.

(Example) The combined mass of the projector (PDG-DWL2500) and the setting plate is

approximately 14 kg (30.9 lb).

Use commercially available anchors.¡

Use M12 nuts, bolts and washers (26 mm outside diameter). Nuts and bolts smaller¡

than M12 could cause the setting plate to fall. (The wall plate must be secured in at

least four places.)

Sanyo takes no responsibility for any damages or injury caused by incorrect installation.¡

0.27 inch

(68 mm)

0.65 inch

(164 mm)

CTRline

Template sheet for

installing the wall plate

Center line of the

projection surface

Unit: inch (mm)

0.51 x 1.30

(13 × 33)

1.77 x 3.15

(45 × 80)

5.15

(135)

1.06

(27)

6.77 (172)

8.82 (224)

15.99 (406)

18.23 (463)

Projection

surface

Center line of

the wall plate

POA-CH-EX06(IJAH).indb4POA-CH-EX06(IJAH).indb4 10.9.811:21:13AM10.9.811:21:13AM

Installation Procedure

Attach the setting plate to the wall plate

1Hang the setting plate hook onto the wall plate slits.

2Tighten the four M8 x 20 mm hexagon socket head cap bolts supplied

with the setting plate. (Secure temporarily so that the adjustment men-

tioned on page 7 can be carried out.)

3Attach the left and right cover plates to the setting plate using the two

M5 x 10 mm hexagon socket head cap bolts included. (Secure temporar-

ily so that the adjustment mentioned on page 7 can be carried out.)

Wall plate

Setting plate

Bolts

POA-CH-EX06(IJAH).indb5POA-CH-EX06(IJAH).indb5 10.9.811:21:13AM10.9.811:21:13AM

English

Installation Procedure

Securing the projector to the setting plate

1Attach the adjustment unit to the

projector using the included 5

screws (M4 x 18). Adjustment unit

Projector

Screws

2Remove the two bolts (for drop-prevention)

from the setting plate. Loosen the four

bolts located on the top of the adjustment

unit and set the projector with the adjust-

ment unit onto the setting plate.

Setting plate

Loosen bolts

Projector with the adjustment unit

Bolts

3Tighten the four bolts which were loosened to secure the projector to

the setting plate. Attach the two bolts (for drop-prevention) to the setting

plate.

Bolts

POA-CH-EX06(IJAH).indb6POA-CH-EX06(IJAH).indb6 10.9.811:21:14AM10.9.811:21:14AM

Installation Procedure

Adjustment

1Adjust the forward/backward slide

(Adjustable range: 0 - 180 mm)

Loosen the four bolts on the top of the setting¡

plate using a hexagon wrench (3 mm) and adjust

the slider of setting plate. After the adjustment,

tighten the four bolts which were loosened.

2Adjust the vertical slide (Adjustable range: +4° - –2°)

Remove the left and right cover plates.¡

Loosen the four bolts¡qlocated inside the setting plate using a hexagon wrench (6 mm).

Adjust the vertical slide with the two bolts¡wlocated inside the setting plate using a hexagon wrench (6

mm) (Adjust the left and right bolts so that their ends touch equally against the wall plate.)

Tighten the four bolts¡qwhich were loosened using the hexagon wrench (6 mm).

After adjustment, attach the left and right cover plates again.¡

3Adjust the horizontal rotation (Adjustable range: +5° - –5°)

Loosen the two bolts¡qlocated on the top of the setting plate using a hexagon wrench (3 mm).

Turn the adjustment knob¡wlocated on the left side of the setting plate to adjust the horizontal rotation.

Tighten the two bolts¡qwhich were loosened using the hexagon wrench (3 mm).

* “A” marks appear on the setting plate to indicate the locations of the bolts and adjustment knob.

Bolts w

Bolts q

4°

2°

Bolts

0 - 7.09 inches

(0 - 180 mm)

Bolts q

Adjustment knob w5° 5°

POA-CH-EX06(IJAH).indb7POA-CH-EX06(IJAH).indb7 10.9.811:21:14AM10.9.811:21:14AM

English

Installation Procedure

4Adjust the vertical tilt (Adjustable range: +5° - –5°)

Loosen the screw¡qlocated on the left side of the setting plate using the hexagon wrench (3 mm).

Turn the adjustment knob¡wlocated on the left top side of the setting plate to adjust the vertical tilt.

Tighten the screw¡qwhich was loosened using the hexagon wrench (3 mm).

5Adjust the horizontal roll (Adjustable range: +5° - –5°)

Loosen the screw¡qlocated on the front right side of the setting plate using the hexagon wrench (3 mm).

Turn the adjustment knob¡wlocated on the right top side of the setting plate to adjust the horizontal roll.

Tighten the screw¡qwhich was loosened using the hexagon wrench (3 mm).

* “B” marks appear on the setting plate to indicate the locations of the screws and adjustment knob.

* “C” marks appear on the setting plate to indicate the locations of the screws and adjustment knob.

Right side

Screw q

Adjustment

knob w

Screw q

Adjustment knob w

5°

POA-CH-EX06(IJAH).indb8POA-CH-EX06(IJAH).indb8 10.9.811:21:14AM10.9.811:21:14AM

Attach the drop-prevention wire to the projector

To prevent the projector from falling down, use the included drop-prevention wire to connect the projector

and the setting plate.

1Pass the included drop-prevention wire through the drop-prevention

wire installation bar of the projector as shown in the illustration.

2Pass the wire through the holes of the setting plate as shown in the il-

lustration.

3Secure the end of the wire at the bottom of the setting plate with the

screw (M4 x 10) supplied with the setting plate as shown in the illustra-

tion.

Drop-prevention wire

Screw (M4 x 10)

Drop-prevention wire installation bar

POA-CH-EX06(IJAH).indb9POA-CH-EX06(IJAH).indb9 10.9.811:21:14AM10.9.811:21:14AM

Inhaltsverzeichnis

Andere Sanyo Projektorzubehör Handbücher

Sanyo

Sanyo POA-SR-140 Bedienungsanleitung

Sanyo

Sanyo PLC-LNS07 Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo POA-MD17SDID Bedienungsanleitung

Sanyo

Sanyo POA-FBOX130 Bedienungsanleitung

Sanyo

Sanyo LNS-T31A - Telephoto Zoom Lens Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo POA-MD03VD2A - Projector Terminal Expansion... Stücklistenhandbuch

Sanyo

Sanyo PJ-Net Organizer POA-PN01 Bedienungsanleitung

Sanyo

Sanyo LNS-S30 Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo PJ-Net Organizer Plus POA-PN02 Bedienungsanleitung

Sanyo

Sanyo LNS-S02 Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo LNS-W32 - Wide-angle Lens - 22.3 mm Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo POA-MD18DVI - Projector Terminal Expansion... Stücklistenhandbuch

Sanyo

Sanyo LNS-W50 Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo POA-MD11DVI Stücklistenhandbuch

Sanyo

Sanyo LNS-S03 - Zoom Lens - 97 mm Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo LNS-W32 - Wide-angle Lens - 22.3 mm Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo MT-EDU102 Bedienungsanleitung

Sanyo

Sanyo LNS-T31A - Telephoto Zoom Lens Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo LNS-W04 Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo POA-MD03VD2A Stücklistenhandbuch

Sanyo

Sanyo POA-SP-SU31 Bedienungsanleitung

Sanyo

Sanyo LNS-S03 - Zoom Lens - 97 mm Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo LNS-W21 Gebrauchs- und Pflegehandbuch

Sanyo

Sanyo LNS-T01 Gebrauchs- und Pflegehandbuch

Beliebte Projektorzubehör Handbücher anderer Marken

Optoma

Optoma BX-AL133B Bedienungsanleitung

PEERLESS

PEERLESS PE 1120 Leitfaden

Osram

Osram SIRIUS HRI Series Handbuch

Presentation Switchers

Presentation Switchers PS111 Bedienungsanleitung

Kramer

Kramer VIA GO Bedienungsanleitung

Yamaha

Yamaha PJL-112 Stücklistenhandbuch

Mitsubishi Electric

Mitsubishi Electric 236CB Betriebsanleitung

Epson

Epson BrightLink 475Wi Bedienungsanleitung

Acer

Acer WP100 Bedienungsanleitung

i3 i3board Bedienungsanleitung

CHIEF

CHIEF HB-43E Bedienungsanleitung

Biamp

Biamp Modena Hub Service-Handbuch

NEC

NEC MP10RX Bedienungsanleitung

Panamorph

Panamorph DCR-S3 Bedienungsanleitung

Exact solutions

Exact solutions FRAME-EVO-P10 Bedienungsanleitung

CHIEF

CHIEF VCM103S Bedienungsanleitung

InFocus

InFocus LP70+ Leitfaden

Sharp

Sharp AN-PH20EZ Bedienungsanleitung