Sanyo VCC-4324 Bedienungsanleitung

INSTRUCTION MANUAL VCC-4324

COLOR CCD CAMERA

About this manual

Before installing and using the camera, please read this manual

carefully. Be sure to keep it handy for later reference.

L53S4/US GB 1998, 10, 27

SANYO INDUSTRIAL VIDEO

COLOR VIDEO CAMERA LIMITED WARRANTY

OBLIGATIONS

In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and

addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC’s warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-800-421-5013.

New Jersey Office

210 Riser Road

Little Ferry, NJ 07643

201-641-3000

California Office

1200 W. Artesia Blvd.

Compton, CA 90220

310-537-5830

Illinois Office

900 N. Arlington Heights Rd.

Itasca, IL 60143

708-775-1414

THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING HAWAII AND ALL U.S. TERRITORIES AND PROTECTORATES. THIS

WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER

AT THE TIME WARRANTY SERVICE IS REQUESTED.

Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO FISHER (USA) CORPORATION warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC

will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail.

LABOR PARTS IMAGE DEVICE

3 YEARS 3 YEARS 3 YEARS

EXCLUSIONS

This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model’s instruction manual, or (B) the repair of any product whose serial number has been altered, defaced

or removed.

This warranty shall not apply to the cabinet or cosmetic parts, antenna, knobs, batteries or image burns to projection or picture tubes caused by electronic devices or games.

This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair.

This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized

service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire,

flood or other Acts of God, or normal wear and tear.

The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability.

THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT

SHALL SFC BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS

UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

ATTENTION

For your protection in the event of theft or loss of this product, please fill in the information below for you own personal records.

Model No._____________________________________________________________________ Serial No. _____________________________________________________________________

(Located on back or bottom side of unit.)

Date of Purchase _______________________________________________________________ Purchase Price _________________________________________________________________

Where Purchased _________________________________________________________________________________________________________________________________________________

L53S4/US GB 1998, 10, 27

Depending on the conditions of use, installation and environment,

please be sure to make the appropriate settings and adjustments. If

you need help with installation and/or settings, please consult your

dealer.

CONTENTS

INFORMATION TO USER..................................................................... 2

PRECAUTIONS...................................................................................... 3

PARTS NAMES ..................................................................................... 4

MOUNTING THE LENS......................................................................... 8

CONNECTIONS..................................................................................... 10

SETTINGS.............................................................................................. 11

TROUBLESHOOTING ........................................................................... 14

SPECIFICATIONS.................................................................................. 15

ACCESSORIES

1C mount adaptor ( mm)....................1 pc.

The C mount adaptor must be used to be able to install a C mount

lens on the camera.

2Lens iris plug (4-pin) ............................1 pc.

FEATURES

•The optical filter is switched automatically to color image or black

and white image according to the subject brightness.

•Built-in interline transfer method 1/3" CCD, approx. 270,000

picture elements

•Low smear, anti-blooming, low lag, no burning and no geometric

distortion using the CCD solid state image device.

•100% solid state components giving excellent immunity to shock

and vibration

•Not subject to interference from magnetic or electrostatic fields

•High sensitivity, minimum required illumination is 0.1 lux (F1.2)

•Horizontal resolution, more than 330 TV lines

•Power supply: 24 V AC operation

L 3S4/US GB 1998, 10, 27

English 1

INFORMATION TO USER

Safety Guard

THIS SYMBOL INDICATES THAT THERE ARE

IMPORTANT OPERATING AND MAINTENANCE

INSTRUCTIONS IN THE LITERATURE ACCOMPANYING

THIS UNIT

WARNING:

TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

This installation should be made by a qualified service person and

should conform to all local codes.

For the customers in Canada

This Class B digital apparatus complies with Canadian ICES-003.

Pour la clientèle canadienne

Cet appareil numerique de la Classe B est conforme a la norme

NMB-003 du Canada.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 1 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 1 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by Sanyo may

void the user’s authority to operate this camera.

L 3S4/US GB 1998, 10, 27

2 English

PRECAUTIONS

In case of problem

Do not use the camera if smoke or a strange odour comes from the

unit, or if it seems not to function correctly. Disconnect the power

cord immediately, and consult your dealer (or a Sanyo Authorized

Service Centre).

Do not open or modify

Do not open the cabinet, as it may be dangerous and cause damage

to the unit. For internal settings and repairs, consult your dealer (or a

Sanyo Authorized Service Centre).

Do not put objects inside the unit

Make sure that no metal objects or flammable substance get inside

the camera. If used with a foreign object inside, it could cause a fire,

short-circuits or damages.

If water or a liquid gets inside the camera, disconnect the power cord

immediately, and consult your dealer (or a Sanyo Authorized Service

Centre). Be careful to protect the camera from rain, sea water, etc.

Be careful when handling the unit

To prevent damages, do not drop the camera or subject it to strong

shock or vibration.

Install away from electric or magnetic fields

If installed close to a TV, radio transmitter, magnet, electric motor,

transformer, audio speakers the magnetic field they generate will

distort the image.

Protect from humidity and dust

To prevent damages to the camera, do not install it where there is

greasy smoke or steam, where the dampness may get too high, or

where there is a lot of dust.

Protect from high temperatures

Do not install close to stoves, or other heat generating devices, such

as spotlights, etc., or where it could be subject to direct sunlight, as

that could cause deformation, discoloration or other damages.

Be careful when installing close to the ceiling, in a kitchen or boiler

room, as the temperature may raise to high levels.

Install where the temperature range will stay between –10˚C and

0˚C.

(no condensation)

Cleaning

•Dirt can be removed from the cabinet by wiping it with a soft

cloth. To remove stains, wipe with a soft cloth moistened with a

soft detergent solution and wrung dry, then wipe dry with dry soft

cloth.

•Do not use benzine, thinner or other chemical product on the

cabinet, as that may cause deformation and paint peeling. Before

using a chemical cloth, make sure to read all accompanying

instructions. Make sure that no plastic or rubber material comes in

contact with the cabinet for a long period of time, as that may

cause damage or paint peeling.

L 3S4/US GB 1998, 10, 27

English 3

PARTS NAMES

1Lens iris output connector (4 pin)

This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens.

2Flange-back adjustment lever (See page 7)

3Flange-back lock screw

4Lens mount cap

The cap is installed to protect the lens mount section.

Remove the lens mount cap before installing a lens (sold separately).

5Camera installation bracket

The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the

longer screws and install the shorter screws on the opposite side to seal the openings.

CAUTION:

When installing the camera support, select a location that can support the total weight of the

camera and accessories

1232

1Shorter screws: M3 x 4

2Longer screws: M3 x 6

3Camera mounting

screw hole:

1/4"-20 UNC

L 3S4/US GB 1998, 10, 27

4 English

PARTS NAMES

6Camera setup section (under the cover)

This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC

(without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings

may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cover fixing

screw, then remove the cover.

Control name Position

aColor and Black/White level switch (C-BW) L

bInternal/Line lock switch (SYNC) INT

cRed and Blue color adjustment volume (R, B) about center

dWhite balance switch (WB) A

eElectronic iris (EI)/Backlight compensation (BLC) switch OFF

fAuto-iris lens switch (A I LENS) DC

gLens iris level volume (LEVEL) about center

Notes:

•The EI/BLC switch cannot be used simultaneously.

•When using a 1/2 or 2/3 inch C mount VIDEO (with EE internal amplifier) auto-iris type lens, set the

A I LENS switch to the VIDEO position.

•If not using an auto-iris lens, make sure the BLC switch is set to OFF.

LEVEL

VIDEO

A. I.

LENS

VR301

OFF

BLC

VR302

VR303

SYNC

L-L

INT

C-BW

d e f g

L 3S4/US GB 1998, 10, 27

English 5

PARTS NAMES

7Power indicator (POWER)

Comes on when the power to the camera is on.

8Video output connector (VIDEO OUT: BNC type)

Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.

9Line phase adjustment volume (LINE PHASE)

When using two cameras or more, the image on the monitor may roll vertically when switching sources. This

rolling can be minimized by turning this volume.

F24 V AC input terminal (24 V AC, GND)

With this camera use only the 24 V AC power adaptor model No. VPT-115 available from Sanyo.

Power supply connections

Use a 3 wire grounded cable (22 AWG or more), and connect as shown by the illustration.

CAUTION:

•To prevent camera and/or AC adaptor failure, pay close attention to polarity when making the

connections.

•To prevent fire hazard any UL listed wire rated VW-1, should be used for the 24 V AC cable input

terminal.

GRD

AC AC

L 3S4/US GB 1998, 10, 27

6 English

PARTS NAMES

Flange-back adjustment

If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of

focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the

flange-back position as described below.

1Using a + screwdriver, loosen the flange-back lock screw (M2:+).

2Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens.

3Set the zoom lens to the maximum wide angle position, set the focus using the flange-back adjustment

lever.

4Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle

shot.

When the setting is complete, tighten the flange-back lock screw.

Note:

When flange-back lock screw is completely tighten it will protrude slightly as shown in the illustration (Fig 1).

Do not tighten the screw further.

Fig. 1

Flange-back lock screw

1, 4

L 3S4/US GB 1998, 10, 27

English 7

MOUNTING THE LENS

Check the lens mount

Do not use a lens if the length “L” is more than 5 mm. That may damage the

camera and prevent proper installation.

Installation of a DC type auto-iris lens (sold separately)

A 1/3 inch CS mount type lens without EE amplifier circuit that only uses a DC power source. This camera can

receive (the A I LENS switch to the DC type) a CS mount type lens without the need of an adaptor.

If the lens plug shape or wiring does not correspond, please install the supplied plug as indicated in the pin

layout table.

Installation of a VIDEO type auto-iris lens (sold separately)

A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit that uses the video signal and a DC power source.

1Remove the lens mount cap.

2Attach the supplied C mount adaptor (A) to the auto-iris lens (B), then install the assembly on the camera.

3Connect the lens plug to the LENS connector on the side of the camera.

If the lens plug shape or wiring does not correspond to the specifications below, connect the supplied plug

as indicated.

•When using lenses from other makers, make sure that the pins connections in the plug correspond to

the ones of the camera.

Refer to the lens specifications to check the pins connections in the plug.

•If they are different than indicated, remove the original plug and connect the supplied plug according to

the diagram.

2 (A) (B)

L 3S4/US GB 1998, 10, 27

8 English

Andere Sanyo Sicherheitskamera Handbücher

Sanyo

Sanyo VCC-4374 Bedienungsanleitung

Sanyo

Sanyo VCC-3924P Bedienungsanleitung

Sanyo

Sanyo VCC-HD4600P Bedienungsanleitung

Sanyo

Sanyo VCC-P7574 - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-MC600P Bedienungsanleitung

Sanyo

Sanyo VCC-9784VA Bedienungsanleitung

Sanyo

Sanyo VDC-C1574VA - CCTV Camera Bedienungsanleitung

Sanyo

Sanyo VCC-HD5600 - Full HD 1080p Day/Night Pan-Tilt-Zoom... Bedienungsanleitung

Sanyo

Sanyo VCC-HD2100 - Full HD 1080p Network Camera Bedienungsanleitung

Sanyo

Sanyo VCC-P9575P Bedienungsanleitung

Sanyo

Sanyo VCC-HD4000P Bedienungsanleitung

Sanyo

Sanyo VDC-D2185VP Bedienungsanleitung

Sanyo

Sanyo VCB-3574IR Bedienungsanleitung

Sanyo

Sanyo VCC-HD5600 - Full HD 1080p Day/Night Pan-Tilt-Zoom... Bedienungsanleitung

Sanyo

Sanyo VCC-HD5400 Benutzerhandbuch

Sanyo

Sanyo VCC-6584E - 1/3" Color CCD DSP High-Resolution... Bedienungsanleitung

Sanyo

Sanyo VCC-9684VA - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VDC-HD3500P Bedienungsanleitung

Sanyo

Sanyo VDC-DP9584N - Network Camera Bedienungsanleitung

Sanyo

Sanyo DSR-HB8000 Bedienungsanleitung

Sanyo

Sanyo VCC-9684VA - 1/4" Color CCD Indoor Mini Dome... Bedienungsanleitung

Sanyo

Sanyo VCC-6584E - 1/3" Color CCD DSP High-Resolution... Bedienungsanleitung

Sanyo

Sanyo VDC-DP7585P Bedienungsanleitung

Sanyo

Sanyo VCB-3524 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung