Satel INT-TSG2 Bedienungsanleitung

Andere Handbücher für INT-TSG2

4

Inhaltsverzeichnis

Andere Satel Tastenfeld Handbücher

Satel

Satel MKP-300 Bedienungsanleitung

Satel

Satel PERFECTA Bedienungsanleitung

Satel

Satel VERSA-LCDM-WRL Bedienungsanleitung

Satel

Satel INT-SCR Bedienungsanleitung

Satel

Satel VERSA INT-TSH2 Betriebsanleitung

Satel

Satel INT-TSI Bedienungsanleitung

Satel

Satel INT-TSG Bedienungsanleitung

Satel

Satel VERSA INT-TSH2 Bedienungsanleitung

Satel

Satel INT-SCR-BL Bedienungsanleitung

Satel

Satel INT-SK Bedienungsanleitung

Satel

Satel CR-MF5 Bedienungsanleitung

Satel

Satel Integra INT-KSG2R Bedienungsanleitung

Satel

Satel CA-64 S Bedienungsanleitung

Satel

Satel Integra INT-KSG2R Bedienungsanleitung

Satel

Satel INT-TSG Benutzerhandbuch

Satel

Satel INT-TS Bedienungsanleitung

Satel

Satel INT-KLCDK-GR Bedienungsanleitung

Satel

Satel INT-TSG2 Bedienungsanleitung

Satel

Satel INT-SF Bedienungsanleitung

Satel

Satel INT-KSG Gebrauchsanweisung

Satel

Satel CR-MF5 Bedienungsanleitung

Satel

Satel INT-TSG2 Bedienungsanleitung

Satel

Satel INT-TSG Benutzerhandbuch

Satel

Satel INT-SK Bedienungsanleitung

Beliebte Tastenfeld Handbücher anderer Marken

ACT

ACT ACT PRO 1030 Bedienungsanleitung

Cardin

Cardin SSB Series Bedienungsanleitung

Harman Kardon

Harman Kardon KP 1 Bedienungsanleitung

Chamberlain

Chamberlain KPR2000 Benutzerhandbuch

CYP

CYP CR-KP1 Bedienungsanleitung

Aeware

Aeware k-35 Series Referenzhandbuch

Aritech

Aritech CS-175 Series Bedienungsanleitung

GE

GE NetworX NX-1600E Series Bedienungsanleitung

Lenze AC Tech

Lenze AC Tech MC SERIES Bedienungsanleitung

Burg Wächter

Burg Wächter secuENTRY 7711 Bedienungsanleitung

Aeware

Aeware in.k450 Bedienungsanleitung

Lenze

Lenze EPM-H410 Bedienungsanleitung

Toshiba

Toshiba RKP007Z Bedienungsanleitung

Gemini

Gemini GEM-DXK1 KEYPAD Bedienungsanleitung

Russound

Russound MDK-C5 Betriebsanleitung

Bosch

Bosch D1260 Series Bedienungsanleitung

Elmes Electronic

Elmes Electronic KB1 Bedienungsanleitung

Clare Controls

Clare Controls ClareOne CLR-C1-PNC Montageanleitung

INT-TSG2

Keypad int-tsg2_sii_en 07/21

Quick installation guide

Full manual is available at www.satel.eu. Scan the QR code to go to

our website and download the manual.

The device should be installed by qualified personnel.

Changes, modifications or repairs not authorized by the manufacturer shall void

your rights under the warranty.

Disconnect power before making any electrical connections.

This is a Class A product. In a domestic environment this product may cause

radio frequency interference.

The keypad is designed for indoor installation. The place of installation should be readily

accessible to the system users.

1. Open the keypad enclosure (Fig. 1). The enclosure opening tool, shown in the illustration,

is included in the keypad delivery set.

2. Place the enclosure base on the wall and mark the location of mounting holes.

3. Drill the holes for wall plugs (screw anchors).

4. Run the wires through the opening in the enclosure base.

2 INT-TSG2 SATEL

5. Use wall plugs (screw anchors) and screws to fasten the enclosure base to the wall.

Select wall plugs specifically intended for the mounting surface (different for concrete or

brick wall, different for drywall, etc.).

6. Connect the DTM, CKM and COM keypad terminals to the appropriate terminals of the

control panel communication bus (Fig. 2). If you use the twisted-pair type of cable,

remember that CKM (clock) and DTM (data) must not be sent through one twisted-pair

cable.

The bus wires must be run in one cable.

The length of cables must not exceed 300 m.

7. If you wish to connect any detectors to the Z1 and Z2 zones, connect the wires to the

terminals (connect the detectors in the same way as to the control panel onboard zones).

8. Connect the supply wires to the KPD and COM terminals. The keypad can be powered

directly from the control panel, from an expander with power supply or from an additional

power supply unit.

9. Place the front panel onto the catches and snap close the enclosure.

10.Turn the power on, set the address and identify the keypad (see full installation manual).

Description of terminals

KPD - power supply input.

COM - common ground.

DTM - data.

CKM - clock.

Z1, Z2 - zones.

RSA, RSB - terminals provided for future applications (RS-485).

The declaration of conformity may be consulted at www.satel.eu/ce

SATEL sp. z o.o. •ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. +48 58 320 94 00

www.satel.eu