Saturn FBGM12-B Bedienungsanleitung

FBGM12-B

FBGM16-B

FBGM23-B

FBGM48-B

FBGM72-B

FBGM48SL-B

FBGM12-W

FBGM16-W

FBGM23-W

FBGM48-W

FBGM72-W

FBGM48SL-W

Saturn Customer Care Toll-Free Service Line:

1-855-877-5430

For additional product and warranty information, please visit

our website at www.GetSaturn.com

Instruction Manual

Glass Door Merchandisers (Swing and Sliding Door)

Table of Contents:

1)Introduction ................................................................................................3

2)Use of the equipment....…….......................................................................3

3)Technical features......................................................................................4

4)Operation....................................................................................................4

5)Digital Display.............................................................................................4

6)Handling......................................................................................................5

7) Installation procedure...............................................................................5

8)Connecting to the main power supply .....................................................5

9)Maintenance instructions..........................................................................6

Cleaning...................................................................................................6

Cleaning the GDM surface.....................................................................6

Cleaning the inside of the GDM.............................................................6

Cleaning the condenser.........................................................................6

10)Troubleshooting ......................................................................................7

11)Technical service.....................................................................................7

12)Unit Diagram.............................................................................................7

Operating Instructions..................................................................................8

Electrical Control Circuit Diagram.............................................................10

Technical Parameters .................................................................................11

Official Approval And Rules…….……………………………………………...12

1. Introduction

This instruction manual provides all the necessary information regarding:

Use of the GDM

Technical specifications

Installation and handling

Operator procedures and instructions

Maintenance operation

The manual is to be considered an integral part of the GDM and should be

stored in a safe place for further consultation for the working life of the GDM.

The manufacturer cannot be held liable in the following cases:

■Improper installation (not in accordance with the guidelines indicated herein)

■Misuse of the GDM

■Power supply defects

■Improper or inadequate maintenance

■Unauthorized modification or tampering

■Use of non-original (NON-OEM) parts

■Partial or total failure to comply with the instructions

All electrical equipment can be hazardous to health. Current standards and

legal requirements must be complied with during the installation and use of

any equipment.

2. Use of the Equipment

The refrigeration units are for storing and preserving fresh, perishable food

and drinks.

The operating temperature for GDM is:

■Between 33°F and 39°F at room temperature of 100°F and 60% RH

3. Technical Features

The GDM is a ventilated system; the evaporator is in a separate insulated box

on the top. All the materials used in the manufacturing of this unit are

guaranteed to be suitable for use with food items. The gases used in the

GDM are R134a; the refrigeration circuit is in compliance with current industry

standards.

4. Operation

The gas in the refrigerating circuit is first compressed, liquefied and then

evaporated in the ventilated evaporator, located on the top of the GDM.

This cycle involves the absorption of heat from the air in the GDM compartment.

The heat produced is then dissipated to the outside environment by a

condenser unit located on the bottom of the GDM.

5. Digital Display

A digital display and switches with built in indicator lights in the bottom panel of

the GDM operate the unit.

The switches and indicator lights are for turning on the power supply and the

lights inside the cabinet and top light box.

The red switch light illuminates to indicate that the unit is powered on.

The green switch light illuminates to indicate that the refrigerator compartment

lights are powered on.

If the switch indicator lights will not illuminate, this indicates that the unit or the

refrigerator compartment the lights are not operable. The digital display is for

the regulation of all parameters to provide the correct operation of the GDM.

Please consult all parameters in the digital display section of this manual.

6. Handling

The GDM arrives in PET film and packed in a cardboard box on a wood pallet.

The GDM must be transported and handled with care. Never place

a GDM on its side or turn it upside down as this may damage or

impair operation of the refrigerated unit. Saturn cannot be held liable for

any damage or defects arising directly or indirectly from improper

handling of the equipment ornon-compliance with the safeguards

illustrated above.

7. Installation Procedures

Place the GDM in the coolest and best ventilated part of the room. Don’t

install the GDM near heat and direct sunlight sources.

Remove the straps securing the cardboard packing.

Remove the cardboard covering. Remove the PET

protection film.

Adjust the leveling legs to isolate the casters from the

ground.

Clean the GDM with mild detergent and then dry itwith a

soft cloth.

The unit should be installed more than 2" from any wall

and at least 8" of clear space above the unit.

If you want to change the artwork in the light box, unscrew

the two screws on one of sides of light box, take off the

cover, pulling out the plastic artwork board from the

channels, replace with new plastic artwork board.

Reassemble light box.

8. Connecting to the MainPower Supply

Qualified professionals must carry out this operation.

The refrigeration units are supplied complete with a power cord for the

connection to the main power supply. A thermomagnetic circuit breaker

(not supplied) must be installed between the main power

point and the power cord of the GDM.

Before proceeding make sure that:

The main voltage corresponds to the voltage on the GDM,which is

115V/60Hz/1Ph; to ensure proper operation it is essential for the power

supply voltage to come within a range of +/-10% of the unit's rated voltage

and the circuit is sized correctly for the load of the GDM.

The electronic system to which the GDM is connected is made in

compliance with current standard requirements

The electric connections and the installation of the thermomagnetic circuit

breaker have been done by qualified electricians.

Connection steps:

Install a thermomagnetic circuit breaker sized for the rated output of the

GDM unit being installed

Plug the GDM unit to the thermomagnetic circuit breaker protected power

outlet.

9. Maintenance Instructions

The smooth operation and life of the GDM is dependent on correct and regular

maintenance.

Cleaning:

Regular cleaning of the GDM unit is strongly recommended each month.

Please follow the instructions below.

Unplug the GDM power cord prior to carrying out any type of

cleaning operation.

Cleaning the GDM surface:

Clean the GDM with mild detergent and then dry it with a soft cloth. Do not

use abrasive detergents!

Cleaning the inside of the GDM:

Clean the inside area at a minimum ofeach month with a

detergent suitable for use with food items.

Cleaning the condenser:

For an efficient operation of the GDM, it is advisable to clean the condenser

regularly approximately every 4 months with a dry brush or vacuum cleaner.

10. Troubleshooting

GDM stops working (light off):

Power supply failure

Solution:

Check that the plug is properly connected

Check that the on/off switch is set to “on”

Check that the main power circuit is on

GDM temperature increases:

Unit is located too close to a heat source

Condenser is dirty or blocked

Solution:

Move the heat source further away

Clean the condenser

11. Technical Service

For technical service, please contact the Saturn Service Department at

1-855-877-5430. Please provide the representative with the serial

number, model number, and the date of purchase.

12. Unit Diagram

1. Power

Switch

4. Evaporator

7. Condenser

10. LED Lamp Switch

2. Microcomputer Controller

5. Evaporator Fan Motor

8. Drain Case

11. Casters

3. Compressor

6. Condenser Fan Motor

9. Shelf

12.Level Foot

1. New, upright air-cooling refrigeration units should

be opened and ventilated before first use. After

ventilation, the interior should be cleaned with

warm water before use.

2. After connecting the power supply, press the GREEN power switch to turn

on the unit. The light should illuminate and the refrigeration unit’s power

will turn on. The microcomputer controller, installed in the controller

keyboard, can automatically adjust the temperature ranges. This intelligent

digital controller works as follows: If the temperature increases and

reaches set point plus differential, the compressor isstarted and then

turned off when the temperature reaches the setpoint value again.

FrontPanelCommands–Digital Display

To display target set point, in programming mode it

selects a parameter or confirm an operation

Press to start a manual defrost

Use to browse the parameter codes, or increase the displayed

value in programming mode

Use to browse the parameter codes, or decrease the displayed

value in programming mode

Key Combinations

Press together to lock or unlock the keyboard

Press together to enter in programming mode

Press together to return to room temperature display

Operating Instructions

1. Push and immediately release the SET key, the set point will be shown.

2. Push and immediately release the SET key or wait about 5 seconds to return

to the normal display.

How to Change the Set Point:

1. Push the SET key for more than 2 seconds to change the Set point value.

2. The value of the set point will be displayed and the “°C” or “°F” LED starts

blinking.

3. To change the Set value push the or arrows.

4. To keep the new set point value, push the SET key again or wait 10 seconds.

How toStart a Manual Defrost:

Push the DEF key for more than 2 seconds and a manual defrost will start.

How toChange a Parameter Value:

To change the parameter’s value, proceed as follows:

1. Enter the Programming mode by pressing the SET+keys for 3s (“°C” or “°F”

LED starts blinking).

2. Select the required parameter. Press the SET key to display its value.

3. Use or to change its value.

4. Press SETto store the new value and move to the following parameter.

To Exit: Press SET+ or wait 15 seconds without pressing a key.

NOTE: The set value is stored even when the procedure is exited by waiting for the

the time-out to occur.

How toSee the Set Point:

2. The “OF” message will be displayed and the keyboard will be locked.

3. If a key is pressed more than 3 seconds the “OF” message will be displayed.

+ keys till the “on”

To Unlock the Keyboard:

Keep pressed together for more than 3 seconds the

message is displayed.

To Lock the Keyboard:

1. Keep pressed for more than 3 seconds the + keys.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Saturn Gewerbliche Lebensmittelgeräte Handbücher

Saturn

Saturn PUC48R Bedienungsanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch