Saxby Lighting Pati Bedienungsanleitung

Pati Bricklight

13818

13819

13820

Thank you for purchasing this light fitting.

Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.

Please retain these instructions for future reference.

Warning

Specification

Installation

Layout

This is a Class 1 product and must be earthed.

Please read these instructions carefully before commencing any work.

This unit must be fitted by a competent and qualified electrician.

Install in accordance with IEE Wiring regulations and current Building Regulations.

To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons

cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified

electrician.

This light fitting should be connected to a circuit with a 30mA RCD fitted.

If replacing an existing fitting, make a careful note of the connections.

Always use the correct type and wattage bulb. Using the incorrect wattage bulb will damage the bulb and ballast.

When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.

Check with your local authority or retailer for recycling advice.

This product is not suitable for dimming.

This product is rated at IP65.

This product is not suitable for location in or near a marine or sea environment.

The entire unit gets hot whilst on for a period of time.

These products should not be fitted to PIR circuits or short duration timed switches. Should you wish to connect

this unit to a timed system please consult the manufacturer before installation.

• Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction

box and the light fitting.

• Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction

boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.

• We recommend that you use H05RN-F specification cable (not supplied) which is an outdoor grade, rubber

sheathed cable. The mains supply cable must have a minimum cross sectional area of 1.0mm²

• Cables that are to be in walls must be protected using suitable conduit or plastic trunking.

Voltage: 240V 50Hz a.c.

Lamp: 26W G24d-3 PLC

IP rating: 65

250mm

84mm

96mm

250mm

84mm

96mm

250mm

84mm

96mm

Existing fittings must be completely removed before installation of a new product. Before removing the existing

fitting, carefully note the position of each set of wires.

1. Undo the screws and remove the bezel, glass and seal from the fitting.

2. Cut the mounting hole for the light unit taking care not to damage any pipes or mains cables beneath the

mounting surface 80mm high x 240mm wide x 100mm deep. Remove the mounting box from the fitting and

ensure that it fits correctly in the hole and is level.

You have correctly identified the wires.

The connections are tight.

No loose strands have been left out of the connection block.

Wiring

Check That

Commissioning

Having correctly identified the wiring from your existing light fitting, connect to the connection block inside the

product in the following way:

NEUTRAL

EARTH (GREEN/YELLOW)

SWITCHED LIVE

BLUE (N)

GREEN/YELLOW

BROWN (L)

SUPPLY LIGHT FITTING

Bezel

Seal

Mounting

Box

Unit

Glass Shade

3. Fit the rear surround into position and secure. This surround may be cemented in position. Wait until the

cement has set before continuing with the installation.

4. Pull the cable through the gland and ensure that it is sealed to ensure that the fitting maintains its IP rating.

5. Place the fitting in position, and secure.

6. Wire as detailed below.

6. Push the unit into the mounting box, ensuring that it sits correctly. Adjust the cable so it does not get snagged.

Refit the screws to hold the unit in place.

7. Refit the seal, shade and bezel. Refit the screws.

8. Replace fuse or circuit breaker and switch on. Your light is now ready for use.

031209

Waste electrical products should not be disposed of with household waste. Please recycle where

facilities exist. Check with your Local Authority or retailer for recycling advice.

For your safety, always switch off the supply before changing lightbulbs, or cleaning.

This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.

Saxby Lighting Ltd. NW10 7UL

Care and Cleaning

Recycling Advice

Safety Information

The shade must be replaced immediately should the shade become cracked or damaged. This

tting must not be used without the shade in place.

Replace Cracked

Shade

We recommend cleaning with a soft dry cloth.

Do not use solvents or abrasive cleaners as these could damage the finish.

Do not clean the units with a pressure washer.

Fitting / Replacing Bulbs

When changing a bulb, always switch off at the mains and allow the bulb to cool

before handling. Used bulbs should not be disposed of with household waste.

Please recycle where facilities exist. Always use the correct type and wattage bulb.

Using the incorrect wattage bulb will damage the bulb and ballast.

PLC 26W 2 PIN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Saxby Lighting Außenleuchte Handbücher

Saxby Lighting

Saxby Lighting Inova PIR Wall Handbuch

Saxby Lighting

Saxby Lighting PYRAMID 1LT WALL Bedienungsanleitung

Saxby Lighting

Saxby Lighting Odyssey ST5008BK Bedienungsanleitung

Saxby Lighting

Saxby Lighting 40655 Handbuch

Saxby Lighting

Saxby Lighting Panther Wall 52016 Handbuch

Saxby Lighting

Saxby Lighting Bosco 1612T35A Handbuch

Saxby Lighting

Saxby Lighting Palin Spike Handbuch

Saxby Lighting

Saxby Lighting Odyssey ST5009BK Bedienungsanleitung

Saxby Lighting

Saxby Lighting Canillo 67699 Bedienungsanleitung

Saxby Lighting

Saxby Lighting Ikon Pro CCT Series Handbuch

Saxby Lighting

Saxby Lighting Severus EL-40105 Handbuch

Saxby Lighting

Saxby Lighting 91963 Bedienungsanleitung

Saxby Lighting

Saxby Lighting Ware Outdoor Wall Handbuch

Saxby Lighting

Saxby Lighting Atlantis Post Handbuch

Saxby Lighting

Saxby Lighting EL-40094 Handbuch

Saxby Lighting

Saxby Lighting Atlantis Post Handbuch

Saxby Lighting

Saxby Lighting OPAZ MV SPIKE Bedienungsanleitung

Saxby Lighting

Saxby Lighting EL-40062 Handbuch

Saxby Lighting

Saxby Lighting Aretz GU10 Recessed Bedienungsanleitung

Saxby Lighting

Saxby Lighting HOXTON RECESSED Bedienungsanleitung

Saxby Lighting

Saxby Lighting Pimlico Bollard Handbuch

Saxby Lighting

Saxby Lighting Doron Wall Handbuch

Saxby Lighting

Saxby Lighting Icarus Photocell 2LT Wall Bedienungsanleitung

Saxby Lighting

Saxby Lighting Picco 95205 Bedienungsanleitung

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

NEBO

NEBO NEB-LSP-0020 Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

BEGA

BEGA 84 253 Handbuch

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung