SCA THW1801 Bedienungsanleitung

SCA

1800W High Pressure Washer

Important - Please read these instructions fully before operating or maintaining your High Pressure Washer

These instructions contain important information that will help you get the best from your High

Pressure Washer, ensuring it remains safe to operate.

If you need help or have damaged or missing parts, call the Customer Helpline on 1300 889 028

THW1801

Instruction Manual

After Sales Support

FREE CALL 1300 889 028

EMAIL:salesau@positecgroup.com

Customer Helpline 1300 889 028

Contents

Safety Information.....................................................................................................3

In The Box..................................................................................................................6

Accessories...............................................................................................................6

Assembly....................................................................................................... 7

Operating Instructions.............................................................................................. 9

Storage....................................................................................................................11

Maintenance.............................................................................................................12

Troubleshooting.....................................................................................................13

Technical Data..........................................................................................................14

Warranty.............................................................................................................14

Customer Helpline 1300 889 028

Safety Information

Important - Please read these instructions fully before starting assembly

Warning Symbols

Warning

Read the operator’s manual

Double insulation

Warning: Do not direct the jet at persons, animals and electrical equipment

Machine not suitable for connection to the potable water mains

RCM marking

ABN: Australian Business Number. By this number, business information such as entity type,

status, business location etc. can be found at website http://abr.business.gov.au.

ABN of Positec Australia Pty Limited is 14 101 682 357

Customer Helpline 1300 889 028

Safety Information

Important - Please read these instructions fully before starting assembly

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow

the warnings and instructions may result in electric shock, ﬁre and/or

serious injury.

Save all warnings and instructions for future reference.

- This machine is not intended for use by persons (including children) with reduced

physical,sensory or mental capabilities, or lack of experience and knowledge.

- Children should be supervised to ensure that they do not play with the appliance.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent

or similarly qualiﬁed persons in order to avoid a hazard.

Additional Power Tool Safety Warnings

WARNING: Do not use the appliance without reading the instruction sheet.

- Safety boots, safety gloves, safety helmets with visors, hearing protection etc. should

be worn while operating the machine.

- When opening the trigger gun, there is a danger of the kickback force and the sudden

torque on the spray assembly. Please hold the nozzles tightly.

- WARNING: High pressure jets can be dangerous if subject to misuse. The jet must not

be directed at persons, live electrical equipment or the machine itself.

- WARNING: Do not use the machine within range of persons unless they wear

protective clothing.

- WARNING: Do not direct the jet against yourself or others in order to clean clothes or

foot-wear.

- Disconnect from the electrical power supply before carrying out user maintenance

- WARNING: High pressure cleaners shall not be used by children or untrained

personnel.

- WARNING: Risk of explosion – Do not spray ﬂammable liquids.

- WARNING: To ensure machine safety, use only original spare parts from the

manufacturer or approved by the manufacturer.

- WARNING: High pressure hoses, ﬁttings and couplings are important for the safety

of the appliance. Use only hoses, ﬁttings and couplings recommended by the

manufacturer

- WARNING: Water that has ﬂown through backﬂow preventers is considered to be non-

potable.

- WARNING: The machine must be disconnected from its power source by removing the

plug from the socket-outlet during cleaning or maintenance and when replacing parts

or converting the machine to another function.

- WARNING: Do not use machine if a supply cord or important parts of the machine are

damaged, e.g. safety devices, high pressure hoses, trigger gun.

- WARNING: If an extension cord is used, the plug and socket must be of watertight

construction.

- WARNING: Inadequate extension cords can be dangerous. If an extension cord is used,

it must be suitable for outdoor use, and the connection has to be kept dry and off the

ground. It is recommended that this is accomplished by means of a cord reel which

keeps the socket at least 60 mm above the ground.

Customer Helpline 1300 889 028

Safety Information

Important - Please read these instructions fully before starting assembly

General Power Tool Safety Warnings

- WARNING: This hose contains electrical connections: do not use it to collect water

and do not immerse in water for cleaning; the hose should be checked regularly and

must not be used if damaged.

- The electric supply connection must be made by a qualiﬁed electrician and comply

with AS/NZS 3000. It is recommended that the electric supply to this machine should

include either a residual current device that will interrupt the supply if the leakage

current to earth exceeds 30 mA for 30 ms or a device that will prove the earth circuit.

Customer Helpline 1300 889 028

In The Box

Parts

Electric cable

Spray gun and lance holder

Handle

ON/OFF switch

Outlet water connector

Inlet water connector

Inlet water hose (not supplied)

Lock off switch

Gun trigger

Spray gun

Adjustable spray nozzle

Extension lance

High pressure hose

Built-in detergent tank

Cable holder

Wheels

Normal nozzle (low pressure)

Nozzle cleaning tool

On board storage for nozzles

Inlet water ﬁlter (See B1)

Accessories

Spray gun 1

5m water outlet high pressure hose 1

Normal nozzle 1

Adjustable spray nozzle 1

Extension lance 1

813

717

10 20

Customer Helpline 1300 889 028

NOTE: Before using the tool, read the instruction book carefully.

Caution!

●Never use the pressure washer to draw in water contaminated with solvents (e.g.

paint thinners, gasoline, oil, etc.).

●Dirt in the feed water will damage the unit. To avoid this risk, we recommended

checking the water ﬁlter (20) (located inside the water inlet; to clean it out see

maintenance section).

●Always prevent debris from being drawn into the unit by using a clean water source

and an water ﬁlter (20) if required.

Water supply (cold water only)

1. Do not draw non-water liquids through the unit. For use with cold water supply only.

2. Water hose must be at least a 1/2” in diameter.

3. Flow rate of water supply must not fall below 6 l /min.

4. Flow rate can be determined by running the water for one minute into an empty

container.

5. The water supply temperature must not exceed 60oC (140oF).

ASSEMBLY

1. ASSEMBLING SPRAY GUN HOLDER

Press the spray gun and lance holder (2) on to the machine. (See A1)

2. MOUNTING OF HOLDER FOR ELECTRIC CABLE

Press the cable holder (15) on to the machine. (See A2)

3. MOUNTING OF HANDLE

Press the handle (3) on to the machine, and ﬁx the six screws. (See A2)

A1 A2

Assembly

Customer Helpline 1300 889 028

Assembly

4. CONNECTION OF INLET WATER HOSE

Note: The inlet water ﬁlter (20) must always be ﬁtted in the water inlet pipe to ﬁlter out

sand, lime stone and other impurities as these will damage the pump valves. (See B1)

Caution: Failure to ﬁt the ﬁlter will invalidate the guarantee.

Connect the inlet water hose with a standard quick coupling.

Screw the inlet water connector (6) tight on to the water inlet. (See B2)

A1 A2

5. ASSEMBLING THE HIGH PRESSURE HOSE

1) Make sure that ON/OFF switch is in OFF position. (See C1)

2) Insert the high-pressure hose to spray gun. (See C2)

3) Insert the high-pressure hose to outlet water connector. (See C2)

4) Push the lance into the trigger gun when inserted to the end turn it. Make sure the lance

is properly ﬁxed to the gun. (See C3)

5) Attach the nozzles. When attaching the nozzle the button (A) on the nozzle should come

out again. Check before activating the trigger that the nozzle is properly ﬁxed. (See C3)

4) Connect the high-pressure hose to the machine. (See C4)

NOTE: Before removing any accessories, make sure that ON/OFF switch is in OFF position.

1) Detach the high pressure hose by pressing the pawl (B) and button (C). (See C2)

2) Detach the extension lance by pushing it to the end and turn it. (See C3)

3) Detach the nozzle by pressing the button (A) on the nozzle. (See C3)

A1 A2

Customer Helpline 1300 889 028

A1 A2

Operating Instructions

OPERATION

1. LOCK OFF SWITCH

The spray gun features a locking device. When the knob is activated, the spray gun cannot

be operated. (See D1)

2. ON/OFF SAFETY SWITCH

1) Connect the plug into a properly grounded outlet.

2) Before turning the unit on, press the gun trigger (9) to bleed any trapped air out of the

pump and hose. (See D2)

3) Your switch is in a locked off position to prevent in accidental starting. Depress lock off

button (8) then gun trigger (9) and release lock off button (8). Your switch is now on. To

switch off just release the gun trigger (9).

A1 A2

Customer Helpline 1300 889 028

Operating Instructions

4. ADDING DETERGENT

1. Unscrew the cap of the built-in detergent tank. (See G1)

2. Add detergent to the tank and screw the cap back on. (See G2)

4) Start the pressure washer by turning ON/OFF switch to ON, let the machine run for a

while to reach the necessary pressure,and then press the gun trigger (9). (See E)

REMINDER: Motor does not run continuously, only when trigger is squeezed.

3. ADJUSTING THE SPRAY

The adjustable spray nozzle can adjust from fan to jet setting. The spray is adjusted from

jet spray to fan spray by turning the nozzle as shown in F.

NOTE: the pressure of the spray on the surface you are cleaning increases as you move

the wand closer to the surface.

CAUTION: Jet spray adjustment is very aggressive. Do not adjust while spraying. We

recommend that for most cleaning applications a 20-degree spray angle should be used

to avoid damage to the surface being sprayed.

Surface preparation

Before staring any cleaning task it is important the area for objects which could create a

hazard. Remove objects from the work area which area which could be tripped over, such

as toys or outdoor furniture. Ensure that all doors and windows are closed tight.

A1 A2

Inhaltsverzeichnis

Andere SCA Hochdruckreiniger Handbücher

SCA

SCA PLU 637450 Bedienungsanleitung

Beliebte Hochdruckreiniger Handbücher anderer Marken

Shark

Shark RG-232637 Bedienungsanleitung

Shakti Technology

Shakti Technology S3 Bedienungsanleitung

Kärcher

Kärcher K 4 Pure Bedienungsanleitung

Porter-Cable

Porter-Cable D25806-025-2 Bedienungsanleitung

REM POWER

REM POWER HDEm 662 Bedienungsanleitung

Landa

Landa HS-3000 Bedienungsanleitung

Craftsman

Craftsman 580.752270 Bedienungsanleitung

HIKOKI

HIKOKI AW 100 Bedienungsanleitung

Delco

Delco DC 1302 Bedienungsanleitung

Kärcher

Kärcher K 3 Full Control Bedienungsanleitung

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Bedienungsanleitung

ARKSEN

ARKSEN 014-HG-14141-HR Bedienungsanleitung

Black & Decker

Black & Decker PW1700SPX Bedienungsanleitung

Kärcher

Kärcher 595 - SPARE Leitfaden

Kranzle

Kranzle B 10 200 Bedienungsanleitung

Stihl

Stihl RE 90 Bedienungsanleitung

Husky

Husky HU80911 Bedienungsanleitung

PowR-Quip

PowR-Quip PQ-2600 Bedienungsanleitung