Schlage Ease S1 SMART DEADBOLT Bedienungsanleitung
Quick Start Guide
S1 SMART DEADBOLT
S1 KEYLESS SMART DEADBOLT
Parts
(S1 Smart Deadbolt shown)
Key
Exterior assembly
Cross bolt
Bolt
Interior assembly
Battery cover
Mounting plate
Mounting screws (3)
Two lengths provided
Cover
Screws (4)
For more information visit schlage.com.au/ease or schlage.co.nz/ease
2
Also includes (not shown):
a) Strike plate & screws
b) Reinforcement plate & screws
c) 4 x AA Alkaline batteries
Exterior assembly
Interior assembly
Preparing for installation
1. Measure the dimension of the hole on your
door to ensure you have a 54mm hole, or
use the drilling template provided.
Ø54mm
(2-1/8”)
No adjustment needed.
2. Adjust the deadbolt.
NOTE: Bolt ships with backset in 60mm (2-3/8”)
position. If required, turn the bolt case and pull
to extend to 70mm (2-3/4”) backset position
(pictured below).
The bolt must be in retracted (unlocked)
position when you are changing backset.
Ø60mm
(2-3/8”)
Ø70mm
(2-3/4”)
Ø60mm
(2-3/8”)
Battery
cover
Reset
button
Thumb
turn
Wireless
module
socket
Status Indicators
Green:
Unlocked or setting success
Red:
Locked or setting failed
Master and User PIN codes have 4~10 digits. The
default master PIN code is [12345678]. Please
change it prior to programming of the lock.
Keypad
Cylinder (S1 only)
Status
indicator
(Green/
Red)
Micro USB port
Spacer
Reboot button
3
Ø70mm
(2-3/4”)
1 2
2. Use a screwdriver to test if deadbolt works
smoothly.
4. Hold the exterior assembly flush to the
door, pull the key tailpiece and cable
through the door hole.
This hole is for
the optional
cross bolt
provided for
stablising your
lock. If you
drilled a hole,
securely tighten
the post before
mounting on
the door.
3. Make sure the bolt is in the retracted
(unlocked) position.
NOTE: The bolt must be in retracted
(unlocked) position before installing
the lockset.
NOTE: Cable must go through door hole
under the bolt.
NOTE: The tailpiece should be kept in a
horizontal position.
Installation
1. Install the bolt on the door ensuring the word
UP is in the upwards position.
4
7. Attach cable assembly to the interior
assembly PCB by lining up notches on
top of cable connector to slots on PCB
connector. Press connector in firmly until
completely connected.
8. Install interior assembly on inside
mounting plate.
NOTE: The horizontal orientation of the
tailpiece as you insert the inside escutcheon
(thumb turn should be vertical).
PCB connector
6. Secure both assemblies using the screws
provided. Make sure the exterior assembly
is vertically aligned. If you added the cross
bolt, securely tighten the post to the
exterior Ease unit with the additional
screw provided.
5. Position the inside mounting plate to sit flush
on the door, ensuring the cable and tailpiece
go through the holes in the mounting plate.
5
Optional
screw
Cable connector
9. Secure using 4 screws through the interior
assembly onto the mounting plate.
NOTE: Test operation using backup
key and thumb turn before installing
batteries, see if bolt extends smoothly.
Keep your lock in
“unlock”status,
insert 4x AA
batteries in
battery pack.
Using a pointed
object, press and
hold the reset
button for over 5
seconds until you
hear the voice guide.
If reset is successful,
the latch bolt will
extend on its own to
learn the orientation
of the door.
10. Reset the lock to learn the
orientation of your door.
NOTE: Resetting the lock before use
is required and crucial for the lock to
operate properly.
B
A
C
Factory defaultSettings
Master PIN code
Auto lock
Beeper
Wrong code entry limit
Shutdown time
Away mode
Bluetooth mode
Disabled
Disabled
Enabled
Enabled
5 times
3 minutes
12345678
6
12. Install reinforcement plate and strike into
door jamb.
11. Install battery cover.
Warnings
Do not install batteries until the lock is completely installed on the door.
Failure to follow these instructions could result in damage to the product and void the factory warranty.
The accuracy of the door preparation is critical for the functioning and security of this product.
Misalignment can cause performance degradation and lessening of security.
Finish Care: This lockset is designed to provide the highest standard of product quality and performance.
Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth.
Do not use lacquer thinner, caustic soaps, abrasive cleaners or polishes as these can damage the coating
and result in tarnishing.
reinforcement
7
Silent mode:
Disables the tone sound.
Status indicators:
Located on exterior assembly.
Definitions
Master mode:
The master mode should be entered by entering
[** Master PIN Code #] to program the lock.
Master PIN code:
The master PIN code is used for programming
and for feature settings.
Auto lock:
After successful code entry and the unit unlocks,
it will automatically re-lock after 30 seconds. This
feature is disabled in default setting.
Shutdown time:
The lock will shutdown for a default of 3 minutes
and not allow operation after the wrong code
entry limit (5 times) has been met. When the unit
is in shutdown, the light will flash if you are trying
to use the keypad.
Manual mode:
Auto lock function can be adjusted to manual
mode. In manual mode the lock can be locked by
pressing any key on the keypad for 2 seconds, or
using the thumb turn from the internal unit.
Item Specifications Notes
External dimensions S1: 161mm (L) x 70mm (W) x 25mm (D)
S1K: 137mm (L) x 70mm (W) x 15mm (D)
S1: 196mm (L) x 73mm (W) x 33mm (D)
S1K: 196mm (L) x 73mm (W) x 33mm (D)
AA alkaline battery x 4
(Operation voltage: 4.6~6.0V)
Operation temperature:
-20ºC to 55ºC
Lasts up to one year
(10 times open/close per day)
Internal dimensions
Battery
Hardware specifications
User PIN code:
The user PIN code operates the lock.
Maximum number of user PIN codes is 20.
Away mode:
This feature can be activated or deactivated in
the Schlage Abode App or the lock itself.
Activating away mode will disable all user codes,
except master away mode. If the lock is opened
with a key or manually from inside, the lock will
trigger an alarm. To deactivate the away mode, you
have to enter master code or deactivate in the app.
Fake PIN code:
Random numbers that are added before or after
the user PIN. This prevents the user PIN from
being exposed.
Reset button:
After reset operation, the lock will be restored
to factory default settings, all user credentials
will be deleted. Refer to page 6 for instructions
on how to reset your lock.
8
Enable/
Disable
Beeper
Enable beeper
Success
2 green lights and 2 beeps
Disable beeper (silent mode)
Success
2 green lights and 2 beeps
Press
41#
Press
42#
Enter
**Master PIN code #
Wait for
2 green lights and 2 beeps
Enable/
Disable
Auto
Lock
Enable auto lock
Success
2 green lights and 2 beeps
Disable auto lock (manual mode)
Success
2 green lights and 2 beeps
Press
51#
Press
52#
Enter
**Master PIN code #
Wait for
2 green lights and 2 beeps
Away
Mode
Enable away mode
Success
2 green lights and 2 beeps
Press
6#
Enter
**Master PIN code #
Wait for
2 green lights and 2 beeps
Enable/
Disable
Bluetooth
Enable Bluetooth
Success
2 green lights and 2 beeps
Disable Bluetooth
Success
2 green lights and 2 beeps
Press
71#
Press
72#
Enter
**Master PIN code #
Wait for
2 green lights and 2 beeps
Delete
User PIN
Code
Enter
Old user PIN code #
Press
3
Enter
**Master PIN code #
Wait for
2 green lights and 2 beeps Success
2 green lights and 2 beeps
Notes:
1. Beeps sound only when sound is enabled. 2. If the indicators show 3 red lights and 3 beeps, your setting has failed.
The system will exit master mode. Please enter master mode to try again. 3. Refer to page 10 for guidelines on setting PIN codes.
Lock operation
Change
Master
PIN Code
Enter
**Master PIN code # Enter
New master PIN code # Enter
New master PIN code #
Press
1
Wait for
2 green lights and 2 beeps Wait for
2 green lights and 2 beeps Success
2 green lights and 2 beeps
Add
User PIN
Code
Enter
**Master PIN code #
Enter
New user PIN code # Repeat
New user PIN code #
Press
2
Wait for
2 green lights and 2 beeps Wait for
2 green lights and 2 beeps Success
2 green lights and 2 beeps
9
How to use
Wireless
module
socket
Unlock the door
1. Unlock the door from outside:
Master/User PIN code or key
2. Unlock the door from inside:
Manual thumb turn
Turn the thumb turn
on inside body.
Master/User
PIN code
Lock the door
1. Lock the door
from outside:
Auto lock mode:
In auto lock mode,
after unlocking, the
bolt will extend out
automatically after
30 seconds.
Press any key on the
keypad for 2 seconds.
Wireless
module
socket
2. Lock the door
from inside:
Auto lock mode:
In auto lock mode,
the device will lock
automatically.
Turn the thumb
turn on inside body.
Manual mode:
Manual mode:
Setting PIN codes
123456 7 8 9
A.
123456789
B.
222222222
C.
3865
D. If
Then
and
Forward number sequence
Backward number sequence
Repeat number sequence
38 1965
19 3865
Contain existing code sequence
1. Master PIN code (4~10 digit):
Default master PIN code is “12345678”,
please modify it after installation.
If you forget your master PIN code, you
can reset your lock back to factory settings
(refer to page 6 for instructions).
2. User PIN code (4~10 digit): User PIN codes
can be set up through master PIN code.
Up to 20 user PIN codes can be stored.
3. Both master and user PIN codes
don’t support the following combination
of numbers.
10
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Schlage Sperren Handbücher
Schlage
Schlage BE467F Bedienungsanleitung
Schlage
Schlage BE499WB Bedienungsanleitung
Schlage
Schlage CONNECT Montageanleitung
Schlage
Schlage AD-201 Bedienungsanleitung
Schlage
Schlage CO-993 Bedienungsanleitung
Schlage
Schlage GF3000 Gravity Force Series Bedienungsanleitung
Schlage
Schlage LINK FE599 Bedienungsanleitung
Schlage
Schlage L9000 Series Bedienungsanleitung
Schlage
Schlage SchlageTouch BE375 Bedienungsanleitung
Schlage
Schlage L9000 Series Bedienungsanleitung
Schlage
Schlage FE59 FLA CAM LH Bedienungsanleitung
Schlage
Schlage FE595 Bedienungsanleitung
Schlage
Schlage Dexter JD60 Bedienungsanleitung
Schlage
Schlage ND72 Bedienungsanleitung
Schlage
Schlage FE51 Bedienungsanleitung
Schlage
Schlage Door Lock Bedienungsanleitung
Schlage
Schlage L-SERIES Bedienungsanleitung
Schlage
Schlage HDB Bedienungsanleitung
Schlage
Schlage BE365 Bedienungsanleitung
Schlage
Schlage 390G+ Bedienungsanleitung
