Schlage L400 Series Bedienungsanleitung

*P516-911*

P516-911

1 Prepare the door for indicator trim

Two Z\," pilot holes are required to mount the indicator.

ONLY ONE SIDE OF THE DOOR – THE INDICATOR SIDE –

REQUIRES THIS PREPARATION. Use the template included in

the package to mark the location of the pilot holes before drilling.

Inside of door Outside of door

¹⁄₈" pilot

hole x 2

¹⁄₈" pilot

hole x 2

For indicator

thumb turn

only

For indicator

thumb turn

only

2 Install lock chassis

Note:

Pilot holes for

INDICATOR

ONLY

DO NOT FULLY TIGHTEN

CHASSIS MOUNTING SCREWS.

Indicator trim is available for either the inside or outside of the door on allowable functions.

Non-indicator trim is furnished on the opposite side of the door.

The L400 lock with indicator is not intended for exterior door applications.

For retrot, see page 6.

Check the door preparation dimensions with the template included in the package.

Tools

Thumb turn

Indicator trim

Cylinder turn

L400 Series Lock with Indicator Sectional Trim

L400 Lock with Indicator

Installation Instructions

3 Install outside cylinder - NON-INDICATOR ONLY

FOR INDICATOR, SKIP TO STEP 4.

3a Insert key halfway into the cylinder.

L463

Exterior

3b Rotate cylinder clockwise.

Key inserted

halfway

4 Install outside cylinder - INDICATOR

4a Install the indicator mounting plate.

Mounting plate

4b Adjust the cam spindle length.

Cut the spindle at the appropriate mark

according to door thickness.

For 2Z\v” door do not cut the spindle.

4c Install the indicator slide and cam.

Indicator

slide

Cam

4d Connect the cam to the indicator slide. The cam must

engage either the left or right side of the indicator slide

according to door handing and indicator location.

• Unlock the door.

• Move the indicator slide against the top rim of the

mounting plate (unlocked position).

• Assemble the cam as shown.

Door Hand/Indicator Location

Lock Type

Non-deadbolt

functions

RH/Outside

LH/Inside

RH/Inside

LH/Outside

Deadbolt

functions

RH/Inside

LH/Outside

RH/Outside

LH/Inside

4e Insert key halfway into the cylinder.

4f Install the indicator faceplate and cylinder with cylinder

spring as shown.

L463

4g Rotate cylinder clockwise.

5 Install inside cylinder or thumb turn –

NON-INDICATOR ONLY

FOR INDICATOR, SKIP TO STEP 6.

Cylinder

5a Insert key halfway into the cylinder.

L463

5b Rotate cylinder clockwise.

— OR —

Thumb turn

Rotate 180°

Extend

deadbolt

Thumbturn

vertical

6 Install inside cylinder – INDICATOR

6a Install the indicator mounting plate.

Mounting plate

6b Adjust the cam spindle length.

Cut the spindle at the appropriate mark

according to door thickness

For 2Z\v” door do not cut the spindle.

6c Install the indicator slide and cam.

Cam

Indicator

slide

6d Connect the cam to the indicator slide. The cam must

engage either the left or right side of the indicator slide

according to door handing and indicator location.

• Unlock the door.

• Move the indicator slide against the top rim of the

mounting plate (unlocked position).

• Assemble the cam as shown.

Door Hand/Indicator Location

Lock Type

Non-deadbolt

functions

RH/Outside

LH/Inside

RH/Inside

LH/Outside

Deadbolt

functions

RH/Inside

LH/Outside

RH/Outside

LH/Inside

6e Insert key halfway into the cylinder.

6f Install the indicator faceplate and cylinder with cylinder

spring as shown.

Key inserted

halfway

Indicator

faceplate

L463

6g Rotate cylinder clockwise.

7a Tighten cylinder mounting screw.

7b Tighten top and bottom chassis mounting screws.

Cylinder

mounting

screw

Chassis

mounting

screws

8 Install armor front

For retrofit instructions, see page 6.

INDICATOR LOCK RETROFIT INSTRUCTIONS

1 Remove armor front

2 Remove cylinder(s) or thumb turn if applicable

2a Loosen the cylinder mounting screw.

2b Remove the inside cylinder or thumb turn.

Cylinder

Key inserted

halfway

Rotate cylinder counterclockwise

— OR —

Thumb turn

Rotate 180°

Extend

deadbolt

2c Remove the outside cylinder.

Key inserted

halfway

Rotate cylinder

counterclockwise

3 Check door preparation

IMPORTANT

• To install the indicator trim, additional door preparation may be required. If additional door preparation is required, remove

the lock chassis from the door before drilling. Steps for reassembly are included in this instruction sheet.

• Please refer to the template included in this package.

• Make sure the door is prepared with any necessary holes for the indicator trim.

4 Complete installation of indicator trim

Go to STEP 4 ON PAGE 2 and follow the instructions to complete the installation of the indicator trim.

Customer Service

1-877-671-7011 www.allegion.com/us

1 Preparar la puerta para el borde con indicador

Préparer la porte pour la garniture d’indicateur

Se requieren dos oricios piloto de Z\,” para montar el

indicador.

SOLO UN LADO DE LA PUERTA – el lado del indicador –

requiere esta preparación. Use la plantilla incluida en el paquete

para marcar la ubicación de los oricios piloto antes de perforar.

Deux trous pilotes de 32 mm (Z\, po) sont requis pour

installer l’indicateur.

SEUL UN CÔTÉ DE LA PORTE – le côté indicateur – exige

cette préparation. Utilisez le gabarit inclus dans l’emballage pour

marquer l’emplacement des trous pilotes avant de les percer.

Interior de la puerta

Intérieure de la porte

Orificios

piloto de ¹⁄₈"

Trous pilotes

(¹⁄₈" po)

x 2

Exterior de la puerta

Extérieure de la porte

Orificios

piloto de ¹⁄₈"

Trous pilotes

(¹⁄₈" po)

x 2

El borde con indicador está disponible para el interior o el exterior

de la puerta para las funciones permitidas. El borde sin indicador

se coloca en el lado opuesto de la puerta.

La cerradura L400 con indicador no está destinada para

aplicaciones en puertas exteriores.

Para una adaptación, vea la página 15.

La garniture d’indicateur est vendue pour l’Intérieur ou l’extérieur de

la porte pour les fonctions autorisées. Une garniture sans indicateur

est fournie pour le côté opposé de la porte.

La serrure L400 avec indicateur n’est pas conçue pour des

utilisations sur une porte extérieur.

Pour la rénovation, reportez-vous à la page 15.

Compruebe las dimensiones de preparación de la puerta con la plantilla incluida en el paquete.

Vériez les dimensions de préparation de la porte à l’aide du gabarit inclus dans l’emballage.

Herramientas / Outils

Cilindro giro

Cylindre tournante

Giro manual

Barrette

tournante

Borde con indicador

Garniture d’indicateur

Cerradura Serie L400 con seccional de seguridad con indicador

Serrure de la série L400 avec sectionnel d’indicateur d’entrée de serrure

Cerradura L400 con indicador

Serrure L400 avec indicateur

Instrucciones de instalación

Notice d’installation

2 Instale el chasis de la cerradura

Installez le bâti de la serrure

Nota: Oricios

piloto solo para

el indicador

Remarque :

Trous pilotes

pour indicateur

uniquement

NO AJUSTE POR COMPLETO LOS

TORNILLOS DE MONTAJE DEL CHASIS.

NE SERREZ PAS COMPLÈTEMENT

LES VIS DE MONTAGE DU BÂTI.

3 Instale el cilindro externo – para BORDE SIN

INDICADOR

Installez le cylindre extérieur – pour la GARNITURE

SANS INDICATEUR

PARA BORDE DE INDICADOR, PASE AL PASO 4.

POUR LA GARNITURE AVEC INDICATEUR,

PASSEZ À L’ÉTAPE 4.

3a Introduzca la llave a mitad de camino en el cilindro.

Insérez la clé à moitié dans le cylindre.

L463

Exterior

Extérieur

3b Gire el cilindro en sentido horario.

Tournez le cylindre dans le sens horaire.

Llave insertada a

mitad de camino

Clé insérée à

moitié

Andere Handbücher für L400 Series

Inhaltsverzeichnis

Sprachen:

Andere Schlage Sperren Handbücher

Schlage

Schlage AL-SERIES Bedienungsanleitung

Schlage

Schlage L-SERIES Bedienungsanleitung

Schlage

Schlage L460 Bedienungsanleitung

Schlage

Schlage Door Locks Bedienungsanleitung

Schlage

Schlage AD-200 Bedienungsanleitung

Schlage

Schlage Everest 29 Bedienungsanleitung

Schlage

Schlage B664 Bedienungsanleitung

Schlage

Schlage B260 Series Bedienungsanleitung

Schlage

Schlage AD-300 Bedienungsanleitung

Schlage

Schlage BE469 Installations- und Benutzerhandbuch

Schlage

Schlage FE595 Bedienungsanleitung

Schlage

Schlage TouchScreen Deadboltwith Alarm Bedienungsanleitung

Schlage

Schlage B80 Bedienungsanleitung

Schlage

Schlage SENSE Bedienungsanleitung

Schlage

Schlage AD-300 Bedienungsanleitung

Schlage

Schlage AL25D Series Bedienungsanleitung

Schlage

Schlage Ease S1 SMART DEADBOLT Bedienungsanleitung

Schlage

Schlage Dexter Residential Lock Bedienungsanleitung

Schlage

Schlage Door Lock Bedienungsanleitung

Schlage

Schlage FE575 Bedienungsanleitung

Schlage

Schlage J Series Technisches Datenblatt

Schlage

Schlage L9010 Bedienungsanleitung

Schlage

Schlage CO-100-CY-70-KP-RHO-626 Bedienungsanleitung

Schlage

Schlage B-Series Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung