Schwank SCH-200-N Montageanleitung

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

SCHWANK GAS-FIRED

INFRA-RED

CONSTRUCTION HEATER

MODEL NUMBER: SCH-200-N / SCH-200-L

CAUTION: Read all instructions before

use. Retain this manual for

further reference.

INSTALLATION /

OWNER’S MANUAL

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

NOTICE:

Schwank Inc., reserves the right to make

changes to equipment and specifications

without obligation or notification.

All codes are current at the time of printing.

This publication, or parts thereof, may not be re-

produced in any form, without prior written

consent from Schwank Inc. Unauthorized

use or distribution of this publication

is strictly prohibited.

Schwank Inc.

5285 Bradco Boulevard

Mississauga, Ontario,

L4W 2A6

phone: (905) 712-4766

fax: (905) 712-8336

Schwank Inc.

PO Box 988

Waynesboro,

Georgia,USA 30830

Phone: (706) 554-6191

Technical Support: 1-877-446-3727

Fax: (706) 554 9390

e-mail: info@schwankheaters.com

http://www.schwankheaters.com

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

TECHNICAL SPECIFICATIONS

Input (BTU) - 200,000 (0 to 4500 ft above sea level)

Height (inches): 44” Width (inches): 31”

Ignition controls: standing Thermostat: finger

pilot touch

control

Tip-over switch: 35º Gas inlet: ½”

Clearances to: 48” (top) Minimum gas: 6” (NG)

Combustibles 52” (side) Pressure (W.C.) 11” (LP)

No electric power required.

TABLE OF CONTENTS

INFORMATION AND SAFETY LABELS 4

1.0 INSTALLATION REQUIREMENTS 6

1.1 GENERAL INSTRUCTIONS 6

1.2 GAS SUPPLY LINE/GAS PRESSURE 6

1.3 VENTILATION REQUIREMENTS 6

1.4 CLEARANCES TO COMBUSTIBLES 6

1.5 MOUNTING INSTRUCTIONS 7

1.6 LIGHTING/SHUTDOWN INSTRUCTIONS 8

2.0 MAINTENANCE 8

3.0 REPLACEMENT PARTS 10

4.0 LIMITED WARRANTY 12

5.0 SERVICE OR WARRANTY CLAIM 13

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

Failure to comply with the precautions and

instructions provided with this heater can result in

death, serious bodily injury and property loss,

damage from hazards of fire explosion, burn,

asphyxiation, and carbon monoxide poisoning,

Only persons who can understand and follow the

instructions should use this heater. Service of this

heater should be performed by a qualified service

person only.

If you need assistance, or heater information such

as an instruction manual, labels, etc. contact your

local dealer.

WARNING WARNING

FOR YOUR SAFETY

•DO NOT store or use gasoline or other

flammable vapors and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

•DO NOT try to light any appliance.

•DO NOT touch any electrical equipment.

•DO NOT use any telephone equipment in the

immediate area.

•Immediately call your gas supplier or call the fire

department.

For Your Information and Safety …

Please read the following warning labels.

Fire, burn, inhalation, and explosion hazard. Keep solid combustibles, such as building materials, paper or

cardboard, a safe distance away from the heater as recommended by the instructions. Never use the heater in

spaces that do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint

thinner, dust particles or unknown chemicals.

WARNING

Improper assembly, adjustment, alteration, service or maintenance can cause injury, property damage, or

death. For assistance or additional information, refer to this manual, or consult a qualified service agency, or

the gas supplier.

WARNING

Page 1

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

WARNING

•DO NOT use heater in living or office areas.

•Approved for heating buildings or structures

under construction, alteration or repair.

•Use only in well ventilated areas.

•Heater must be used exclusively for heating

purposes.

•The distance between the heating surface top to

the nearest combustible must be at least 48

inches. The distance from the burner surface, in

a horizontal plane, to the nearest combustible

must be at least 52 inches.

•The heater must not be directed towards any LP

gas container within 15 feet.

•The fuel supply line must not be placed near the

burner heat zone.

•DO NOT store or use gasoline or other

flammable vapors or liquids in the vicinity of this

or any other appliance.

•DO NOT use this heater if any part has been

under water. Call a professional gas appliance

service person to inspect the heater, and to

replace any part which has been under water.

•Any changes to this heater or the heater’s

controls can be very dangerous.

•Any part removed must be replaced prior to

operating the heater.

•Failure to follow these warnings may result in

property damage, bodily injury or death.

•The heater must be installed in such a way that it

is not directly exposed to water spray, rain and or

dripping water.

HEATER

MUST BE

LEVEL

BEFORE

OPERATING

NOT FOR HOME OR

RECREATIONAL VEHICLE USE

This heater is designed and approved for use as

a construction heater per Canadian Standard

2.14 and Ansi Z83.7-2000.

CHECK WITH YOUR LOCAL FIRE SAFETY

AUTHORITY IF YOU HAVE ANY QUESTIONS

ABOUT APPLICATIONS.

Other standards govern the use of fuel gases and

heat producing products in specific applications.

Your local authority can advise you about these.

WARNING WARNING

Page 2

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

WARNING

Room Volume cu.ft. No. of air changes / HR

5000 10

7,500 6

10,000 5

15,000 3

20,000 2.5

25,000 2

50,000 1

Required room air changes per hour

for each SCH-200 in operation.

1.2 GAS SUPPLY & PRESSURE INFORMATION

All piping and hose must be installed according to

local code, and must be of adequate size and

construction.

Natural gas models must have the supply line limited

to 14 inches (maximum) water column.

If the line pressure will go above 14 inches water

column at any time, a separate regulator must be

used. The minimum supply line pressure at the inlet to

the heater regulator must in no case be lower than 6

inches of water column.

Note: The regulator is an internal component of the

heater and maintains the heater’s manifold pressure;

natural gas is 5 inches water column, and LP gas is 10

inches water column.

Heaters equipped for LP gas operations must have a

minimum supply line pressure 11 inches of water

column at the heater. Maximum line pressure is 1/2

PSI (14 inches water column).

It has been determined that CO2levels should not

exceed 5000 PPM (parts per million) and CO should

not exceed 35 PPM for an eight hour continuous ex-

posure.

Combustion of gas fuel requires air. Each SCH-200

heater requires 200 sq.in. of opening for combustion

air. (ex.: 20” x 10” window opening)

To maintain the carbon dioxide content in the air at

or below the concentration mentioned above, the

number of air changes are listed below depending on

the size of the space being heated:

1.3 VENTILATION REQUIREMENTS

TABLE 1

MODEL

SIDE

( From Radiant

Surface)

TOP

(From Radiant

Surface)

SCH-200-N

SCH-200-L

52”

48”

1.4 CLEARANCES TO COMBUSTIBLES

TABLE 2

1.0 INSTALLATION REQUIREMENTS

1.1 GENERAL INSTRUCTIONS

1. Examine contents for damage or missing parts

before proceeding with these instructions.

2. Installation of heaters must conform to all local codes.

3. Ensure that heater is level before operation.

Page 3

1. Minimum hose length –

Canada- fifteen feet (15’) — USA-ten feet (10’)

Maximum hose length - fifty feet (50’)

(1” inside diameter)

2. LP Gas Cylinder must be located a minimum

fifteen feet away from heater while heater is in

operation.

3. After assembly and every time the heater is

attached to a new gas cylinder or gas meter,

check for leaks with a soap solution or leak tester

on all gas lines and connections. Failure to do so

may result in property damage, bodily injury or

death. DO NOT USE AN OPEN FLAME.

If high pressure is used to check for leaks, do not

subject this heater’s controls to excessive pressure.

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

1.5 MOUNTING INSTRUCTIONS

FIGURE 1: FREE STANDING FLOOR MOUNT

A steel rod, non-combustible base is an integral part of this heater.

The heater may safely be placed directly on a combustible surface.

Always maintain minimum distance to combustibles as shown in

Table 2. Gas supply hose/piping must lay over the top of bottom

rim of heater as shown here.

On floor mounted units, the Gas supply

line must lay above the bottom rim of

heater. See Figure 2.

Surface of heater will be hot to the touch.

Take proper precautions. If heater

location must be changed, allow

heater to cool a full 15 minutes before

attempting to relocate.

NOTE: Heater is equipped with a tilt safety

feature. Heater will automatically shut down

when it is tilted over 35 degrees.

WARNING CAUTION

GAS SUPPLY LINE

Page 4

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

1.6 LIGHTING / SHUTDOWN INSTRUCTIONS

2.0 MAINTENANCE

This heater should be cleaned at least once annually with a dry cloth. This heater should be inspected before

each use and at least once annually by a qualified service person.

The gas hose assembly shall be visually inspected prior to each use of the heater. If damage is evident it must be

replaced prior to the heater being placed into operation. For replacement part information, see page 9 & 10.

LP model heaters should use a standard LP gas cylinder. Cylinder must be located a minimum of 10 feet away

from heater while heater is in operation. The cylinder must be provided with a system for vapor withdrawal. The

gas must be turned off at the LP gas supply cylinder when the heater is not in use. The connection of the gas cyl-

inder should be made with the #510 connector which tightens by turning the threads to the left. To disconnect the

fitting make sure the gas is turned off, and loosen threads by turning them to the right. When heater is to be

stored indoors the connection between the LP gas cylinder and the heater must be disconnected. The cylinder

must be stored in accordance the Canadian National Code for the Storage and Handling of L.P. Gases.

Keep appliance area free and clear from combustible materials, gasoline and other flammable vapors and liquids.

Ensure that the flow of combustion and ventilation air is free from all obstructions.

1. Set thermostat to “coolest” (lowest) setting.

2. Pre-purge gas line prior to lighting.

3. Open the door in the compartment above filter section.

4. Turn gas control knob clockwise to OFF. Wait five

minutes to dissipate any unburned gas. Sniff around

the appliance near the floor.

Don’t relight pilot if you smell gas.

5. Turn gas control knob counterclockwise to PILOT.

Push down and hold the knob while you light pilot

burner.

6. Hold the gas control knob down about one minute,

then release. If the pilot goes out, turn gas control

knob clockwise to OFF. Repeat steps 1-3.

7. Release gas control knob. If pilot remains lit, turn

counterclockwise to ON.

8. Close the door.

9. Set thermostat to desired setting.

Page 5

SP-MCH2-BX-07A

SCH-200 MANUAL

R.D: Sept 2004

RL: 7

Clearing Burner Screen:

- Make sure gas supply is off

- Use compressed air If air is not available on the site, aerosol can is available: Part # JH-0930-XX

- Insert air nozzle through the pilot lighting hole at side of mantle base

- Direct at flame retaining screen, and blow out any accumulated dust

- Re-open gas supply

- Re-light pilot, and continue using the construction heater as before.

Replace filter at least:

- once every 2 weeks

- minimum once a day when sanding drywall

- each time when connecting heater at different location

* Clean burner screen with each filter change;

( see next window )

Filter replacement:

- Shut off gas supply

- Grasp filter retainer and pull together at retainer grips

- Free filter retainer

- Remove and discard filter

- Replace with a new filter

- Reinstall filter retainer, complete with filter

FILTER RETAINER

FILTER

Page 6

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Schwank Heizung Handbücher

Schwank

Schwank SchwankAir 4000-Recessed Series Bedienungsanleitung

Schwank

Schwank X-Series Betriebsanleitung

Schwank

Schwank STR Series Betriebsanleitung

Schwank

Schwank STV-JZ Bedienungsanleitung

Schwank

Schwank Select14 Series Bedienungsanleitung

Schwank

Schwank deltaSchwank Series Bedienungsanleitung

Schwank

Schwank SST-MX Series Bedienungsanleitung

Schwank

Schwank SchwankAir 3200-Recessed Series Bedienungsanleitung

Schwank

Schwank sportSchwank Series Montageanleitung

Schwank

Schwank SPW2-JZ Series Betriebsanleitung

Schwank

Schwank P40U Bedienungsanleitung

Schwank

Schwank STR-JZ Betriebsanleitung

Schwank

Schwank Select12 Series Bedienungsanleitung

Schwank

Schwank bistroSchwank Series Betriebsanleitung

Schwank

Schwank SchwankAir 4000 Series Bedienungsanleitung

Schwank

Schwank infraSchwank D Series Bedienungsanleitung

Schwank

Schwank STS-JZ Betriebsanleitung

Schwank

Schwank 20S L Bedienungsanleitung

Schwank

Schwank STS-JZ Betriebsanleitung

Schwank

Schwank SPW-JZ Betriebsanleitung

Schwank

Schwank 20S L Bedienungsanleitung

Schwank

Schwank Swift5 Series Bedienungsanleitung

Schwank

Schwank SEM 200-70 Montageanleitung

Schwank

Schwank STS-JZ Betriebsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung