SCIFIT AC7000M Bedienungsanleitung
AC7000M Limit Switch Replacement
If your unit is equipped with a safety pan follow procedure 1. If your treadmill
has a solid motor plate that extends all the way to the front of the unit, go
directly to procedure 2.
Procedure 1
1. Elevate the treadmill to 15% grade. Disconnect power by unplugging the
treadmill power cord from wall socket.
2. Using a ½” socket, remove bolts holding safety pan (A1446) on the bottom
of the elevation assembly.
3. Disconnect wires running to each limit switch (P1260).
4. On the backside of the bracket that the limit switches mount to, remove
the two (2) nuts holding the limit switches in place. Remove switches.
5. Re-attach wires in the same order on the new limit switches.
6. Replace the new limit switches through the same two (2) holes that the
other ones were removed from. Make sure the two (2) legs on the limit
switches clear the elevation rack (A1508).
7. Replace the two (2) 4-40 machine nuts on the backside of the bracket.
8. Install the bolts back in the bottom of the safety pan.
9. Calibrate the elevation using the Elevation Calibration procedure
explained in the Club Mode for your version of software.
Procedure 2
1. With the treadmill at 0% elevation, turn power switch to the off position.
2. Using a Philips screwdriver, remove the motor hood.
3. Disconnect the 6-pin and 8-pin telco cables from the lower board.
4. Disconnect the green static drain wire. This wire comes out of the hole in
the left upright and has a connector between the upright base and the
lower board mounting plate.
5. Using a ½” socket and extension, remove the four (4) bolts with washers
and the four (4) nuts with washers from the upright bases.
6. Remove the upright assembly by lifting it up over the elevation racks and
set it off to the side.
7. Disconnect wires running to each limit switch (P1260).
8. On the backside of the bracket that the limit switches mount to, remove
the two (2) nuts holding the limit switches in place. Remove switches.
9. Re-attach wires in the same order on the new limit switches.
10.Replace the new limit switches through the same two (2) holes that the
other ones were removed from. Make sure the two (2) legs on the limit
switches clear the elevation rack (A1508).
11.Replace the two (2) 4-40 machine nuts on the backside of the bracket.
12.Set the upright assembly back in place. Make sure not to catch the
wires on the elevation racks.
13.Reinstall and tighten the bolts, washers, and nuts to secure the uprights in
place.
14.Plug the telco cables into the lower PCB.
15.Reconnect the green static drain wire.
16. Calibrate the elevation using the Elevation Calibration procedure
explained in the Club Mode for your version of software.
12-04-03 te
Inhaltsverzeichnis
Andere SCIFIT Tretmühle Handbücher
SCIFIT
SCIFIT AC5000 series Bedienungsanleitung
SCIFIT
SCIFIT AC5000 series Bedienungsanleitung
SCIFIT
SCIFIT DC1000 Intelli-Fit Bedienungsanleitung
SCIFIT
SCIFIT AC5000 series Bedienungsanleitung
SCIFIT
SCIFIT Fit-Key AC7000 Bedienungsanleitung
SCIFIT
SCIFIT AC5000 series Leitfaden
SCIFIT
SCIFIT DC4000 Bedienungsanleitung
SCIFIT
SCIFIT DC1000 Intelli-Fit Leitfaden
Beliebte Tretmühle Handbücher anderer Marken
Smooth Fitness
Smooth Fitness EVO 3i Bedienungsanleitung
NordicTrack
NordicTrack NETL81810.0 Bedienungsanleitung
Schwinn
Schwinn 830/Journey 8.0 Bedienungsanleitung
Keys Fitness
Keys Fitness HealthTrainer HT-740T Bedienungsanleitung
Spirit
Spirit XT8 Bedienungsanleitung
NordicTrack
NordicTrack T 14.0 Treadmill Bedienungsanleitung