SDC S6300 Series Bedienungsanleitung
801 Avenida Acaso, Camarillo, Ca. 93012
• (805) 494-0622 • www.sdcsecurity.com
E-mail: [email protected]
These instructions are presented a in step by step sequence.
Please read it through before installation.
Note: The dimensions of the Template are shown in inches. See
attached page for the Metric Conversion Table for millimeters.
P:\INSTALLATION INST\Mechanical Hardware\INST-S6300.vsd Rev C 02-17 Page 1
P:\INSTALLATION INST\Mechanical Hardware\INST-S6300.vsd Rev C 02-17 Page 2
BEFORE INSTALLING THIS EXIT DEVICE :
1. Check device to be sure the type is correct for the application
2. Check device for the correct length, finish and outside trim to be used.
NOTE: This model device has 3 different lengths:
For use on 3' wide door device = approx. 33"
For use on 3-1/2’ wide door device = approx. 40"
For use on 4' wide door device = approx 44"
The lengths of devices are precut for 36", 42" and 48" wide door use,
no additional cutting is necessary. If narrow door installation is required,
cut device at “A” portion to door width minus 4" to fit properly.
DESIGNATION OF PARTS
Chassis Cover
Chassis
Chassis
Push Bar
End Cap
End Cap Bracket
Dogging Device
(Fire Exit Hardware is not
equipped with this device)
Mortise
Strike
Face
Plate Mortise
Lockcase
A
P:\INSTALLATION INST\Mechanical Hardware\INST-S6300.vsd Rev C 02-17 Page 3
1. MARK DOOR FOR DEVICE AND LOCK
2. INSTALL STRIKE TO FRAME OR INACTIVE DOOR
1. Install strike to drilled position on frame or inactive door and secure in place with supplied
screws (Fig 2-1 & 2-2).
2. Be sure auxiliary latch of lock does not enter strike opening.
1. If door is already cut out for lock (mortised), check for proper clearance (Fig 1-1).
2. Mark the center line of device by drawing a line across the door 40" above finished floor (Fig 1-2).
3. Tape template to door and frame then mark mounting holes for device chassis and strike.
4. Cut-out and drill holes as marked on door and frame.
Fig 1-1
1/4”
8-1/32”
31/32”
6-17/32”
4-23/32”
Fig 1-2
40" to
Finished Floor
of Device
L
C
of Mortise Lock
L
C
of Device
L
C
1-5/16”
1/8”
DEEP
3-3/8”
1/8
DEEP
Fig 2-2
To door edge of
inactive door
4-7/8”
1-5/16”
1/8”
DEEP
of Mortise Lock
L
C
of Strike
L
C
1/8” DEEP
1/8”
DEEP
3/8”
4-7/8”
4.7 DIA DRILL
#12-24 TAP
Fig 2-1
To frame on
single door
P:\INSTALLATION INST\Mechanical Hardware\INST-S6300.vsd Rev B 02-17 Page 4
3. SET LOCK HANDING
A) Set the lock for proper handing to match door hand.
1) Change latch bolt handing:
If the handing of the latch bolt doesn’t match door hand, remove fixing screw and pull
latch bolt out from lock case. Turn complete latch bolt unit around to match door
handing. Reinstall latch bolt and fasten it in place (Fig 3-1 & 3-2).
Fig 3-1
Remove screw
Fig 3-2
Pull out and turn
2) Set outside hand of lock case:
There are two catch screws of lock hand on both sides of chassis. Take catch screw
out from one side of chassis which is going to face outside of door (Fig 3-3). Another
catch screw must always be on inside of chassis. For RH and RHRB, the catch screw
will be on the lock case side. For LH and LHRB, the catch screw will be on the lock case
cover side.
Take a catch screw out from one
side of the chassis which is going
to be installed with a trim on the
outside face of the door
Fig 3-3
P:\INSTALLATION INST\Mechanical Hardware\INST-S6300.vsd Rev C 02-17 Page 5
Check that the hub of the lock is seated in the correct position before proceeding to the next step.
Insert spindle into hub of the lock case and turn until latch bolt is retracted (Fig 3-4).
On the side of the lock case that is
attaching to the trim, check that
turning the spindle retracts the
latch bolt before installing the lock
case into the mortise cut-out.
4. INSTALL LOCK CASE IN DOOR
Insert lock case into mortise cut-out
and fasten to door with two flat head screws (Fig 4)
Fig 4
Fig 3-4
P:\INSTALLATION INST\Mechanical Hardware\INST-S6300.vsd Rev C 02-17 Page 6
5. INSTALL DEVICE:
1. Remove chassis cover from chassis assembly and end cap from end cap bracket.
2. Insert the Pull Finger beneath device chassis into the “A” hole in lock case (Fig 5-1)
then mount device horizontally to the drilled position with 6 supplied screws to door (Fig 5-2).
3. Place end cap bracket as a template, mark and drill holes then screw it to secure the device.
4. Check device for correct operation:
A. Depress Push Bar, latch bolt should retract to flush position.
B. Release Push Bar, latch bolt is fully extended.
5. Tighten all screws and bolts.
Fig 5-2
Fig 5-1
A
P:\INSTALLATION INST\Mechanical Hardware\INST-S6300.vsd Rev C 02-17 Page 7
6. INSTALL OUTSIDE TRIM AND CYLINDER
NOTE: Follow this step only if SDC’s Entry Lever trim is used. If other trim is used with
this device, please refer to the original manufacturers instructions.
1. Check the direction of the outside lever to be installed, then place the reversible spring cage
into ferrules with the arrow pointing in the direction of the lever rotation and fasten with screws
supplied (Fig 6-1).
2. Insert spindle into hub of spring cage on outside trim (Fig 6-2).
Ferrule
Reversible
spring cage
Mounting
post
Fig 6-1 Fig 6-2
3. Install outside trim with mounting posts through door and position spindle into hub of lock case
(Fig 6-3)
4. Mount two long screws through device chassis into the mounting posts of outside trim.
5. Screw cylinder into threaded hole of lock case (Fig 6-4).
6. Tighten the set screw counter-clockwise against cylinder as shown.
Fig 6-3 Fig 6-4
7. Install face plate onto lock case front and fasten with
supplied screws (Fig 6-5).
Fig 6-5
P:\INSTALLATION INST\Mechanical Hardware\INST-S6300.vsd Rev C 02-17 Page 8
7. TEST OPERATION AND INSTALL COVERS
1. Test push bar and dogging operation before installing covers:
A. NO TRIM: Latch bolt is retracted by depressing push bar inside.
B. WITH TRIM: Latch bolt is retracted by push bar inside, and;
a) When outside key locks the lever/knob, the lever/knob will be made inoperative.
b) When outside key unlocks the lever/knob, the lever/knob can retract the latch bolt.
C. DOGGING: See dogging description and chart below.
2. Check and secure latch bolt engagement. Adjust strike if necessary.
3. Install chassis cover on chassis assembly.
4. Install end cap on end cap bracket.
DOOR HANDING
Use this diagram to determine
the handing of the door.
NOTE:
For extending the life of this device,
it is recommended utilizing the Dogging feature during high traffic periods of
the day (Panic device only).
OUTSIDE OF DOOR
MULLION
INSIDE OF DOOR
RHR LHR
Depress
push bar
Release Dogging:
Depress push bar,
insert dogging wrench
and turn counter-clockwise 15 .
The push bar will return to the up
position and the latches will
project to lock the door.
Depress
push bar
Dogging:
Depress push bar,
insert dogging wrench
and turn clockwise 15 .
The push bar will remain
pressed and the latches will
keep retracted.
Dogging wrench
(Allen key)
Inhaltsverzeichnis
Andere SDC Türschloss Handbücher
SDC
SDC Z7200R Bedienungsanleitung
SDC
SDC 1190A Series Bedienungsanleitung
SDC
SDC 180 Series Bedienungsanleitung
SDC
SDC EntryCheck E75 Series Bedienungsanleitung
SDC
SDC 1291 ADMR Spacesaver Bedienungsanleitung
SDC
SDC Z7200 Bedienungsanleitung
SDC
SDC Spacesaver 1091 ADMR Bedienungsanleitung
SDC
SDC ZA7200 Series Bedienungsanleitung
SDC
SDC S6100 Series Bedienungsanleitung
SDC
SDC E75 Series Betriebsanleitung
SDC
SDC Z7700 Series Bedienungsanleitung
SDC
SDC E75 Series Bedienungsanleitung
SDC
SDC E75 Series Betriebsanleitung
SDC
SDC 1511S Bedienungsanleitung
SDC
SDC Z7500 Series Bedienungsanleitung
SDC
SDC Z7600 Series Bedienungsanleitung
SDC
SDC 352 Narrow Line EMLock Bedienungsanleitung
SDC
SDC Z7835 Bedienungsanleitung
SDC
SDC E72 EntryCheck Fehlerbehebungshandbuch
SDC
SDC TEMPLATE 180 SERIES Bedienungsanleitung
