SDC 1190A Series Bedienungsanleitung

M:\INS\Temp-1190A REV A 0702 Page 1

Security Door Controls

3580 Willow Lane

Westlake Village, CA 91359

(805) 494-0622

Fax: (805) 494-8861

www.sdcsecurity.com

E-mail: service@sdscecurity.com

TEMPLATE

1190A

DATE 3/19/01

DRAWING

3293

NOTE: TEMPLATE DIMENSIONS ARE SUBJECT TO CHANGE WITHOUT

NOTICE.

TECHNICAL DATA (for standard unit)

FACE PLATE: 8” X 11/2” X 1/8”

STRIKE: 4” X 11/2” X 1/8”

ID REQUIREMENTS: 8” X 11/2” X 11/2”

FINISH: US28 STANDARD (PLATED FINISHES OPTIONAL)

BOLT: 3/4” DIA. SOLID STAINLESS STEEL

BOLT THROW: 3/4”, ROTATING

FAIL-SAFE: LOCKED WHEN ENERGIZED

AUTO RELOCK SWITCH: ADJUSTABLE BALL TYPE

SOLENOID: CONTINUOUS DUTY

ELECTRICAL DATA: 19 WATTS - .8 AMP MAX AT 24VDC

A RECTIFIER IS SUPPLIED FOR AC

OPERATION

(SPECIFY VOLTAGE REQUIRED)

STATUS SENSORS: BOLT AND DOOR POSITION (OPTIONAL)

NOTE: FOR WOOD INSTALLATION CONSULT FACTORY.

SECURITY DOOR CONTROLS

3580 Willow Lane, Westlake Village, CA 91361-4921 • (805) 494-0622 • Fax: (805) 494-8861

www.sdcsecurity.com • E-mail: service@sdcsecurity.com

INSTALLATION INSTRUCTIONS

FS23M, 1090, 1190 SERIES

OVERHEAD INSTALLATION HORIZONTAL

1. Examine the top rail of the door for the most suitable location for the strike. Mark the door for the end of the strike closet to the lock

stile, and make a corresponding mark on the header to line up with the first mark.

2. Locate center line of door thickness on the header and attach adhesive cut out template to header. Lining it up with marks, center

punch the tab-mounting screw locations and counter-sink for #10 screw. Saw or rout out the cutout area.

SIDEJAMB INSTALLATION VERTICAL

3. Examine the lock stile jamb for the point nearest the center of the door height, with space available for the lock and strike. Mark the

door stile horizontal for the top end of the strike and make a corresponding mark on the jamb.

4. Locate center line of door thickness on the jamb and attach adhesive cutout template to jamb, lining up the the top of the cutout with

the horizontal mark on the jamb. Center punch the tab mounting screw locations and counter sink for #10 screw. Saw or rout the

cutout 1-1/2” x 8”.

5. Attach the mounting tabs inside.

6. (FS23M only) bore 5/16” hole for pilot lamp on inside face of frame as shown.

7. Attach power supply leads to lock leads as shown. Handle the lock carefully; do not hang it by the wire leads. Insert wires into the

header cavity carefully so they do not interfere with proper locating of the lock in the cutout.

8. Insert lock. Horizontally, the bolt end is nearest the lock stile. Vertically, the bolt must be at the top end of the cutout. Secure with

10/32 machine screw.

9. Using strike for a template, mark screw hole location and drill holes for screws supplied. Mortise as required. Attach strike.

10. The automatic relock switch is set for 1/8” clearance between the top of the door and transom bar or head jamb. Any additional

gap may be compensated for by loosening the lock nut and turning the switch assembly clockwise until proper adjustment is

reached. Be sure to tighten lock nut when adjustment is satisfactory.

All Space Saver locks are easi-

ly installed in any existing

entrance merely by mortising

out a cutout, attaching the

wiring, inserting the lock, and

bolting it into position with two

attaching tabs. Cutting studs is

no longer a problem or

expense.

Easy Installation or Servicing

M:\INS\INST-90 DEG REV A 0702 Page 1

2. Position screws

for attaching tabs,

drill holes, attach

tabs.

1. Mortise cutout in

tube for face plate

(fits flush with

surface of tube).

3. Connect wiring

to lock.

4. Slide lock into

position, attach

to tabs.

SPECIFICATIONS

FS23M Face plate: 8” x 1-1/2” x 1/8” (203.2mm x 38.1mm x 3.175mm)

I.D. Requirements: 8” x 1-1/2” x 1-1/2”

(203.2mm x 38.1mm x 38.1mm)

Solenoid: Continuous duty

Standard voltage: 24VDC, 0.5 Amp

12VDC, 1 Amp

Strike: M-Mortise 4” x 1-1/2” x 0.125” (101.6mm x 38.1mm x 3.175mm)

For wood 1-3/4” deep (44.45mm)

Bolt: 5/8” (15.88mm) dia. nylon with magnet insert, 5/8” (15.88mm) throw. Red pilot

lamp standard to indicate door locked.

1091A/1091ADC (Deadlocking)

Face plate: 8” x 1-1/2” 0.125” (35.1mm x 35.1mm x 3.175mm)

1091STA: 4-7/8” x 1-1/4” x 0.0937” ANSI

(123.53mm x 31.75mm x 2.28mm)

I.D. Req. 8” x 1-1/2” x 1-1/2”

(203.2mm x 38.1mm x 38.1mm)

Solenoid: Continuous duty

Standard voltage: 24VDC, 0.5 Amp

12VDC, 1 AMP

Strike: M-Mortise 4” x 1-1/2” x 0.125” (101.6mm x 38.1mm x 44.45mm)

Bolt: 5/8” (15.88mm) dia. S.S., 3/4” (6.35mm) throw

1190A

Face plate: 8” x 1-1/2” x 0.125”

(203.2mm x 38.1mm x 3.175mm)

I.D. Requirements: 8” x 1-1/2” x 1-1/2”

(203.2mm x 38.1mm x 38.1mm)

Solenoid: Continuous duty

Standard voltage: 24VDC, 0.7 Amp

Strike: M-Mortise 4” x 1-1/2” x 0.125” (101.6mm x 38.1mm x 3.175mm)

Bolt: 3/4” (6.35mm) dia. S.S., 3/4” (6.35) throw

TROUBLE SHOOTING

Problem Solution

Bolt does not project Check voltage and alignment

of strike.

Bolt projects but chatters Voltage too low.

Bolt will not retract Strike misaligned

BOLT POSITION SENSOR (MAGNETIC)

No. 6 SPDT Indicates bolt locked or unlocked .25 Amp

DOOR POSITION SENSOR (MAGNETIC)

No.9 SPDT Indicates door opened or closed .25 Amp

DOOR POSITION SWITCH (MECHANICAL)

DPS SPDT Indicates door opened or closed 5 Amp

DIMENSIONS: INCHES

MILLIMETER

Drill for Pilot

Lamp on inside

face of frame

M:\INS\INST-90 DEG REV A 0702 Page 2

DOOR IS SHOWN CLOSED AND LOCKED.

UNLOCKING MAY BE CONTROLLED BY

MULTIPLE SWITCH LOCATIONS.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SDC Türschloss Handbücher

SDC

SDC PBD2090A Bedienungsanleitung

SDC

SDC S6300 Series Bedienungsanleitung

SDC

SDC Z7200R Bedienungsanleitung

SDC

SDC Z7500 Series Bedienungsanleitung

SDC

SDC Z7800 Series Bedienungsanleitung

SDC

SDC 1291 ADMR Spacesaver Bedienungsanleitung

SDC

SDC 1511S Bedienungsanleitung

SDC

SDC ZY7500 Series Bedienungsanleitung

SDC

SDC ZA7200 Series Bedienungsanleitung

SDC

SDC Z7500 Series Bedienungsanleitung

SDC

SDC EntryCheck E75 Series Bedienungsanleitung

SDC

SDC Z7200 Bedienungsanleitung

SDC

SDC 352 Narrow Line EMLock Bedienungsanleitung

SDC

SDC 1511S Bedienungsanleitung

SDC

SDC S6200 Series Bedienungsanleitung

SDC

SDC E75 Series Betriebsanleitung

SDC

SDC TEMPLATE 180 SERIES Bedienungsanleitung

SDC

SDC EntryCheck 918 Bedienungsanleitung

SDC

SDC 180 Series Bedienungsanleitung

SDC

SDC FS23M Series Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

SDC

SDC Z7700 Series Bedienungsanleitung

SDC

SDC S6800 Series Kurzanleitung

SDC

SDC Z7835 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

We.lock

We.lock SECBNEBL51 Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

JAKO

JAKO JKBTNX4 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung