Se-Kure Controls SK-554NP-RKAC-4 Bedienungsanleitung

SK-947-RK-6

Remote Key with Small Barrel & 72" Cable

(Included with the SK-554NP-RKAC-4)

SKD-3840PLE

6' Dual Sensor – USB Sensor & Rectangular Sensor

SK-974AH

1/2" Dia. Barrel Sensor Adhesive

SK-395M

AC/DC Power Supply (5 volt. - 1 Amp)

with International Electrical Plug Ends

Installation Instructions for the

4-on-1 Alarm w/Remote Keyway

®Inc.

3714 Runge Street

Franklin Park, IL 60131

1-(800) 322-2435

(847) 288-1111

Fax: (847) 288-9999

On the Web:

www.se-kure.com

E-Mail:

[email protected]

SK-905

1" x 2" Rectangular Adhesive

SK-974PLE

6' Barrel Sensor

SK-554NP-RKAC-4

4-on-1 Alarm with No Power

1. Mount the Remote Key

within 72" of the Alarm

Module, and plug it into the

Remote Key Jack on the

Alarm Module.

2. Insert the key, push in and

turn clockwise. (This places

the Alarm in the “Stand-by”

position).

Note: The key can only be

removed in the “ON”

position.

3. Insert the appropriate

adapter into the SK-395M

AC/DC power supply. Plug it

into an electrical outlet, and

the other end into the AC/DC

Power Supply Jack on the

Alarm Module.

4. Choose a small flat area on

the product where the sensor

is to be applied.

VERY IMPORTANT! NOTE: Clean

the area on the display product and

the sensor with Alcohol Prep Pads.

Wipe these surfaces DRY with a

clean paper towel. If the paper

towel shows dirt, REPEAT THIS

CLEANING STEP until the sur-

faces are CLEAN & DRY!

Clean &

Wipe Dry

When replacing Adhesive

5. Remove the sensor adhesive

from its backing sheet. Apply

the adhesive pad to the bottom

of the sensor, making sure that

the center hole of the adhesive

lines up with the plunger on the

bottom of the

sensor.

Battery Test

AC/DC

Power

Supply

Jack

Remote Keyway

Jack

Horn

Assembly Instructions:

Sensor

Ports

The Alarm is now Ready & Active.

Additional Instructions:

1. Your alarm is equipped with 4 ports.

If only one port is used on a

displayed product a shunt plug must

be installed into any unused ports. If

this is not done the alarm will sound.

2. Prior to placing the sensor on the

product, the area where the sensor

is to be applied must be cleaned

with the alcohol wipe provided, then

thoroughly dried before attaching

the sensor.

3. For the alarm system to function the

remote key must be plugged into the

alarm unit.

4. When attaching the alarm to the

surface follow the cleaning instru-

tions for the sensor given in step 2

above.

Installation Instructions for the

4-on-1 Alarm w/Remote Keyway

®Inc.

3714 Runge Street

Franklin Park, IL 60131

1-(800) 322-2435

(847) 288-1111

Fax: (847) 288-9999

On the Web:

www.se-kure.com

E-Mail:

[email protected]

Battery

Connector

Cover

Plate

Remote Keyway

Jack

9-volt

Alkaline

Battery

(Not

Included)

AC/DC

Adapter

Jack

Battery

Installation:

1. Remove the (4)

phillips head screws

to open the battery

compartment as

shown in the

diagram.

2. Attach a 9-volt

Alkaline Battery

(not included) to the

connector, and insert

the battery into the

compartment.

3. Replace the

cover plate and the

(4) phillips head

screws.

Note: Tighten screw

until it stops– Do

Not Over-Tighten

Optional Battery Back-Up Installation

The 4-on-1 Alarm will operate normally without a battery, but will not alarm when

power to the SK-395M AC/DC Power Supply is interupted.

For Back-Up purposes when the circiut loses power, follow the optional battery

backup installation instructions below.

6. Remove the backing sheet from

the other side of the adhesive pad

and position the sensor over the

flat area of the display product

previously cleaned. Press the

sensor firmly into place to insure

a proper bond.

7. Following the important cleaning

steps, apply the base adhesive

to the alarm module and adhere

it to the display surface.

Turn the key counter clockwise

to the “ON” position and remove.

Inhaltsverzeichnis

Andere Se-Kure Controls Sicherheitssystem Handbücher

Se-Kure Controls

Se-Kure Controls Klothing Kontrols SK-3600 Series Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SK-554 Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SK-T6 Montageanleitung

Se-Kure Controls

Se-Kure Controls LE PLUS Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SK-800KME Series Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SK-903KB Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls K-9 WatchDog Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls Vantage II Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls Mini T Series Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls ME Jr. plus 2 SK-800MEI Series Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SP-101 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung

Pego

Pego ECP APE03 Bedienungsanleitung