Se-Kure Controls SK-903KB Bedienungsanleitung

Installation Instructions for the

Outdoor Product Alarm System

SK-903KB

Outdoor Product Alarm Module w/External Horn

SK-947KB8

Outdoor Cable (Available in Combinations of 8') - [xx = 8, 16, 24, etc.]

SK-907KB

Outdoor Product Alarm Splitter

SK-195

AC/DC Power Supply

SKP-416K

Security Screw Allen Wrench

SK-109KB

Terminator Loop

SK-109KB

Terminator Loop

SK-109KB

Terminator Loop

SK-947KB

Outdoor Cable

SK-947KB

Outdoor Cable

SK-903KB

Outdoor Product

Alarm w/Keypad &

External Horn

SK-195

AC/DC

Power supply

SK-907KB

Outdoor Splitter

Dry Contacts

(can handle up to 24v)

1 Amp

Ground (GREEN)

(connect eyelet to

center screw on

standard outlet plates)

Installation Instructions:

Special Note: Make all connections before installing

batteries and connecting the AC/DC Power Supply.

Indoors:

1. Screw the Alarm Module’s Green Ground Wire to the

ground screw located on the center of a grounded 110v AC

outlet cover plate, and plug the AC/DC Power Supply into

the outlet. (Hold off until the battery step to plug the Power

Supply into the Alarm Module).

2. Attach an (SK-947KB) Outdoor Cable to the end of the

Alarm Module Cable, and extend it Outdoors.

Outdoors:

3. Connect the cable extending from indoors to the

(SK-907KB) Outdoor Splitter. (The Splitter can be mounted

to a wall with #10 screws).

Do not allow Splitter or Connectors

to remain in standing water.

Se-Kure Controls,

®Inc.

3714 Runge Street • Franklin Park, IL 60131 • 1-(800) 322-2435 • (847) 288-1111 • Fax: (847) 288-9999

®Inc.

Battery Installation:

8. Remove the (4) Security Screw from

around the base of the Alarm Module with

the (SKP-416K) Security Allen Wrench.

9. Lift and remove the cover of the

(SK-903KB) Alarm Module.

10. Install (2) 9-v Alkaline batteries as

shown at right, and push firmly onto the

printed circuit board.

11. Replace the cover and the (4) security screws, and then plug in the AC/DC Power Supply.

Note: The cover security screws must be installed and tightened to prevent the alarm from sounding.

Low Battery Power Alarm

Low Battery Light will (((flash))) and Alarm will “CHIRP” when

batteries need to be replaced.

(When replacing batteries, refer to the Keypad Operating

Instructions to place the system in the “Stand-By” Position before removing security screws).

Outdoors: (continued)

4. Connect a (SK-947KB) Outdoor Product Cable to the (SK-907KB) Outdoor Splitter.

5. Pass the cable(s) through an enclosed area of each product, (such as spokes, or steer-

ing wheels) to protect all the display merchandise in the line, as shown above.

6. Thread the end of an (SK-947KB) Outdoor Cable

through the loop of a (SK-109KB) Terminator Loop, and

Lasso an enclosed area of the last product in line by

connecting the Terminator Loop and Cable Connector.

7. Repeat the procedure for the other side of the

(SK-907KB) Outdoor Splitter.

Note: If the other side of the Splitter is not in use, a Terminator

Loop needs to be in that connection to create a “Closed Circuit” in

the system.

Remove Security

Screws

SK-109KB

Terminator Loop

SK-109KB

Terminator Loop

SK-947KB

Outdoor Cable

Outdoor Display

Products

Outdoor Display

Products

SK-907KB

Outdoor Splitter

Last

Outdoor

Display

Products

Last Outdoor

Display Products

SK-109KB

Terminator Loop

Inhaltsverzeichnis

Andere Se-Kure Controls Sicherheitssystem Handbücher

Se-Kure Controls

Se-Kure Controls Mini T Series Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SP-101 Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SK-554 Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls Klothing Kontrols SK-3600 Series Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls ME Jr. plus 2 SK-800MEI Series Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls K-9 WatchDog Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SK-554NP-RKAC-4 Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls LE PLUS Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls Vantage II Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SK-800KME Series Bedienungsanleitung

Se-Kure Controls

Se-Kure Controls SK-T6 Montageanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung

Pego

Pego ECP APE03 Bedienungsanleitung