Se-Kure Controls Vantage II Bedienungsanleitung
Page 1
Vantage II Alarm Instructions
Mounting
Instructions:
Install the
Vantage Alarm Base
NOTE: the LED Light on the stand will blink yellow. This only indicates that
the Vantage Alarm has power but has not been programmed.
Battery Installation:
1.
Remove the (2) two security
screws around the base of
the stand with a SKP-190
TPS Security Bit. (Save these
screws for reinstallation).
2.
Pull the Battery Holder Tab
from inside of the stand (you
will find it lodged in the tube
after the top has been
removed).
3.
Install (3) three new Alkaline
AAA Batteries making sure to
follow the (-) negative and (+)
positive polarity markings on
the battery holder.
4.
Insert the Battery holder into
the display stand tube and
replace the top. Replace and
tighten the screws.
1.
Remove the (2) two security
screws at the top of the stand
with the SKP-200K Security
Wrench. (Save these screws
for reinstallation).
2. Lift the stand off from the
base plate.
SKP-200K Security Wrench
SKP-190 TPS Security Bit
Mounting the Vantage Alarm:
NOTE: the LED Light on the stand will blink yellow. This indicates that the Vantage Alarm has
power but has not been programmed. The yellow light blinks all the time until programed.
7. Lower the plastic cone aligning the screw holes, replace the (2)
two security screws and tighten with the SKP-190 TPS Security
Bit.
3. Position the Vantage Alarm Base Plate(s)
on the display as you want the stands to
be positioned. (See the Base Plate
Template for Positioning & Marking). For
Drilling: mark the display through the pro-
vided Base Plate Template with an awl or
center punch.
4. Drill holes for the size and type of hard-
ware you intend to use to secure the base
plate to the display.
5. Mount the Base Plate(s) to the display:
The base plate provides (4) four 1/4 inch
holes for mounting hardware. Use the
appropriate wood screws, metal screws
or nuts & bolts for your display surface.
(We Do Not Recommend Using Flat
Head Beveled Screws to mount the base
plate to the display). For Glass
Displays: we recommend using double sided adhesive mounting pads.
6. Place the Stand(s) on the mounted Base Plate(s) so the screw
holes on each side of the cone will align with the holes on each
side of the base plate.
Front
of Display
Page 2
Se-Kure Controls,
®Inc.
3714 Runge Street • Franklin Park, IL 60131 • 1-(800) 322-2435 • (847) 288-1111 • Fax: (847) 288-9999
Rev. 04/21/08 SCI-9891 ©2007 Se-Kure Controls,®Inc.
Andere Se-Kure Controls Sicherheitssystem Handbücher
Se-Kure Controls
Se-Kure Controls K-9 WatchDog Bedienungsanleitung
Se-Kure Controls
Se-Kure Controls LE PLUS Bedienungsanleitung
Se-Kure Controls
Se-Kure Controls SK-554NP-RKAC-4 Bedienungsanleitung
Se-Kure Controls
Se-Kure Controls SK-554 Bedienungsanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Se-Kure Controls
Se-Kure Controls SK-903KB Bedienungsanleitung
Se-Kure Controls
Se-Kure Controls Mini T Series Bedienungsanleitung
Se-Kure Controls
Se-Kure Controls SK-T6 Montageanleitung
Se-Kure Controls
Se-Kure Controls Klothing Kontrols SK-3600 Series Bedienungsanleitung
Se-Kure Controls
Se-Kure Controls SK-800KME Series Bedienungsanleitung
