Seagull Models Mini Nemsis EP Bedienungsanleitung
1
www.seagullmodels.com
ASSEMBLY MANUAL
MS: X114
Specifications:
Wingspan-----------------------38.8in(98.5cm).
Wingarea-------------------248sq.in(16sqdm).
Weight----------------1.9-2.1lbs(0.85-0.95kg).
Length-------------------------------31.1in(79cm).
Speedcontrol(ESC)-------------15A-30Aamp.
Motor -------------------------------------- 450-480.
Radio-----------4channelswith5miniservos.
Battery3-cell1800mAhto2100mAhLi-Po.
10 x 5E Electric Prop.
“Graphics and specifications may change without notice”.
MINI NEMSIS EP Instruction Manual.
2
INTRODUCTION.
Thank you for choosing the MINI NEMESIS EP ARTF by SEAGULL MODELS COMPANY LTD.
The MINI NEMESIS EP was designed with the intermediate/advanced sport flyer in mind. It is a
semi scale airplane which is easy to fly and quick to assemble. The airframe is conventionally built
usingbalsa,plywoodtomakeitstrongerthantheaverageARTF,yetthedesignallowstheaeroplane
to be kept light. You will find that most of the work has been done for you already.The motor mount
has been fitted and the hinges are pre-installed . Flying the MINI NEMESIS EP is simply a joy.
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manualthoroughlybeforestartingassemblyofyour MININEMESISEP.Usethepartslistingbelow
to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenewpilotonhis waytosuccessful R/Cflight.They willalsobe able
to advise on any insurance and safety regulations that may apply.
KIT CONTENTS
1
2
9
2
4
3
3
8
5
7
6
488
3
www.seagullmodels.com
KIT CONTENTS.
1 SEAX11401
2 SEAX11402
3 SEAX11403
4 SEAX11404
5 SEAX11405
6 SEAX11406
7 SEAX11407
8 SEAX11408
9 SEAX11409
ADDITIONAL ITEMS REQUIRED.
Motor 450-480
4 channel radio with 5 mini servos
Suitablepropeller
The control surfaces, including the
ailerons, elevators, and rudder, are
prehinged with hinges installed, but
the hinges are not glued in place. It
is imperative that you properly
adhere the hinges in place per the
steps that follow using a high-quality
thin C/A glue.
HINGING THE AILERONS .
Note:
1) Carefully remove the aileron from one
of the wing panels. Note the position of the
hinges.
2)Remove eachhinge fromthe wingpanel
and aileron and place a T-pin in the center of
each hinge. Slide each hinge into the aileron
untiltheT-pinis snugagainstthe aileron.This
will help ensure an equal amount of hinge is
oneithersideofthehingelinewhentheaileron
is mounted to the wing panel.
Hinge.
T-pin.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue
30 minute epoxy
5 minute epoxy
Hand or electric drill
Assorted drill bits
Modellingknife
Straight edge ruler
2mm ball driver
Phillips head screwdriver
220 grit sandpaper
90° square or builder’s triangle
Wire cutters
Masking tape & T-pins
Thread-lock
Paper towels
3) Slide the aileron on the wing panel until
there is only a slight gap. The hinge is now
centered on the wing panel and aileron.
Remove the T-pins and snug the aileron
against the wing panel.A gap of 1/64” or less
shouldbe maintainedbetweenthe wingpanel
andaileron.
MINI NEMSIS EP Instruction Manual.
4
8)Afterboth ailerons are securelyhinged,
firmly grasp the wing panel and aileron to
make sure the hinges are securely glued and
cannot be pulled out. Do this by carefully
applying medium pressure, trying to separate
the aileron from the wing panel. Use caution
not to crush the wing structure.
7) Repeat this process with the other wing
panel, securely hinging the aileron in place.
6) Using C/A remover/debonder and a
papertowel, removeanyexcessC/Aglue that
may have accumulated on the wing or in the
aileronhingearea.
5)Turn thewing panelover anddeflectthe
aileron in the opposite direction from the
opposite side. Apply thin C/A glue to each
hinge,makingsure thattheC/Apenetratesinto
both the aileron and wing panel.
Workthe aileron upanddownseveral
times to “work in” the hinges and
check for proper movement.
Note:
4) Deflect the aileron and completely
saturate each hinge with thin C/A glue. The
aileronsfront surfaceshould lightlycontactthe
wing during this procedure. Ideally, when
thehinges are glued in place, a 1/64” gap or
less will be maintained throughout the lengh
of the aileron to the wing panel hinge line.
Hinge.
Thehinge isconstructedof aspecial
material that allows the C/A to wick
or penetrate and distribute
throughout the hinge, securely
bonding it to the wood structure of
the wing panel and aileron.
Note:
HINGING THE ELEVATORS.
Glue the elevator hinges in place using the
same techniques used to hinge the ailerons.
5
www.seagullmodels.com
HINGING THE RUDDER.
Glue the rudder hinges in place using the
same techniques used to hinge the ailerons.
INSTALL THE AILERONS CONTROL
HORN.
Hinge.
Epoxy.
Aileronfiberglass
control horn .
INSTALL ELEVATOR CONTROL HORN.
INSTALL RUDDER CONTROL HORN.
Elevatorfiberglass
controlhorn.
Epoxy.
Fiberglass
control horn.
Fiberglass
control horn.
Fiberglass
control horn.
MINI NEMSIS EP Instruction Manual.
6
INSTALLING THE FUSELAGE SERVOS.
Elevator servo.
Rudder servo.
1) Installtherubber grommetsand brass
colletsontothe throttleservo. Testfitthe servo
into the aileron servo mount.
2) Secure the servos with the screws pro-
vided with your radio system.
Because the size of servos differ, you
mayneed toadjustthe sizeoftheprecutopen-
ing in the mount. The notch in the sides of the
mount allow the servo lead to pass through.
Rudder fiberglass
control horn.
Epoxy.
Cut.
Elevator servo.
Rudder servo.
Cut.
FUSELAGE SERVO ARM INSTALLATION.
Installadjustableservo connectorinthe servo
arm as same as picture below:
WHEEL AND WHEEL PANTS.
1) Assembling and mounting the wheel
pants to the landing gear as shown below
pictures.
Elevator servo arm.
7
www.seagullmodels.com
2) Follow diagram below for wheel pant
installation:
3) You have to trim each axle using a toll
cutting and cut-off wheel.
Cautionwhencutting theaxlesand wear
protective goggles.
INSTALLING THE MAIN LANDING GEAR
TO FUSELAGE.
5) The blind nuts for securing the landing
gearare alreadymountedinsidethefuselage.
6) Using the hardware provided, mount
the main landing gear to the fuselage.
7) Placethe fuselageinverted onthework-
benchin asuitable stand.Set thelanding gear
in place and use a screwdrive to secure the
landing gear to the fuselage using bolts
M4x20mmand washers.Make sureto usethe
threadlock on the bolts so they don’t vibrate
loose.
4) A drop of C/A glue on the wheel collar
screws will help keep them from coming lose
duringoperation.
Repeat the process for the other wheel.
wheel Pant.
wheel.
M3.
wheel collar.
nut. Axle.
Washer.
Lite-Plywood
block.
MINI NEMSIS EP Instruction Manual.
8
2) Place the servo between the mounting
blocksandspace itfromthehatch. Useapencil
to mark the mounting hole locations on the
blocks.
3) Use drill bit in a pin vise to drill the mouting
holes in the blocks.
1) Usinga small weight(Weightedfuelpick-up
workswell) andstring, feed thestring through
the wing as indicated.
Because the size of servos differ, you
mayneedto adjustthesize oftheprecutopen-
ing in the mount. The notch in the sides of
themountallowtheservoleadtopassthrough.
4) Apply 2-3 drops of thin C/A to each of the
mounting holes. Allow the C/Ato cure without
using accelerator.
6) Secure the servo to the aileron hatch using
Phillips screwdriver and the screws provided
with the servo.
5) Use dental floss to secure the connection
so they cannot become unplugged.
Lockerglue.
.
M3 x 10mm.
Servos.
Smallweight. Thread.
INSTALLING THEAILERON.
9
www.seagullmodels.com
7) Apply 1-2 drops of thin C/A to each of the
mounting tabs. Allow the C/A to cure without
using accelerator.
8) A string has been provided in the wing to
pull the aileron lead through to the wing root.
Remove the string from the wing at the servo
location and use the tape to attach it to the
servoextension lead.Pull theleadthroughthe
wing and remove the string.
9) Set the aileron hatch in place and use a
Phillips screw driver to install it with four wood
screws.
Aileronservo.
MINI NEMSIS EP Instruction Manual.
10
M3 x 15mm.
Electric motor.
140mm.
4mm.
2) Attach the electric motor box to the firewall
suitable with the cross lines drawn on the electric
motor box and firewall. Using epoxy and balsa
stick to secure the motor box to the firewall.
Please see pictures below.
3) Attach the motor to the front of the electric
motor box using four 3mm blind nut, four
M3x15mm hex head bolts to secure the motor.
Please see picture shown.
Epoxy.
Balsa.
Epoxy.
ELECTRIC POWER ASSEMBLY.
1) Locate the items neccessary to install the
electric power installation.
15A-30A.
450-480.
Inhaltsverzeichnis
Andere Seagull Models Spielzeug Handbücher
Seagull Models
Seagull Models Piper Cub Bedienungsanleitung
Seagull Models
Seagull Models PERCIVAL MEW GULL Bedienungsanleitung
Seagull Models
Seagull Models DECATHLON ARTF Bedienungsanleitung
Seagull Models
Seagull Models Low Wing Sport V2 10cc ARF Bedienungsanleitung
Seagull Models
Seagull Models Extra 300S Bedienungsanleitung
Seagull Models
Seagull Models Embraer EMB-312 Tucano T-27 Brazilian Air Force 85 span... Bedienungsanleitung
Seagull Models
Seagull Models SEA232 Bedienungsanleitung
Seagull Models
Seagull Models T-6A Texan II Bedienungsanleitung
Seagull Models
Seagull Models SEA FURY Bedienungsanleitung
Seagull Models
Seagull Models AT 6 TEXAN Bedienungsanleitung
Seagull Models
Seagull Models X-RAY Bedienungsanleitung
Seagull Models
Seagull Models T-34C MENTOR Bedienungsanleitung
Seagull Models
Seagull Models JUMPER 25 Bedienungsanleitung
Seagull Models
Seagull Models CAP 232 Bedienungsanleitung
Seagull Models
Seagull Models SEA158 Bedienungsanleitung
Seagull Models
Seagull Models VAN'S RV- 8 Bedienungsanleitung
Seagull Models
Seagull Models SEA361 Bedienungsanleitung
Seagull Models
Seagull Models Radial Rocket JD 10cc Bedienungsanleitung
Seagull Models
Seagull Models DECATHLON ARTF Bedienungsanleitung
Seagull Models
Seagull Models CHRISTEN HUSKY SEA180 Bedienungsanleitung
