Sealey VS027.V2 Bedienungsanleitung

INSTRUCTIONS FOR:

BRAKE FLUID TESTER

MODEL NO: VS027.V2

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

1. SAFETY

2. INTRODUCTION

3. SPECIFICATION

4. PREPARATION

1.1 GENERAL SAFETY

 DO NOT use the tester to perform a task for which it is not designed.

 DO NOT allow untrained persons to use the tester.

 DO NOT use whilst under the influence of drugs, alcohol or

intoxicating medication.

 Keep children and unauthorised persons away from the work area.

 Keep work area clean and tidy and free from unrelated materials.

 Ensure the work area has adequate lighting.

 After use, clean equipment and store in a cool, dry, child proof area.

 WARNING!Brake fluid is flammable - keep away from sources of

ignition, including hot surfaces e.g. exhaust manifold.

1.2. BRAKE FLUID SAFETY

 WARNING!Brake fluid will damage paintwork. Any spillage should be

flushed with water immediately.

Always read and comply with the warnings on the brake fluid

container.

Wear eye protection and keep skin contact to a minimum. If brake

fluid enters eyes rinse with plenty of water and seek medical advice.

If swallowed seek medical advice immediately.

Dispose of waste fluid in accordance with local authority regulations.

Comparative electrolytic type tester. Checks moisture content of uid by

resistance to electric current. Easily calibrated using new brake uid.

Audible test cycle with three LED read-out. Just insert probe and press button

for immediate result. Works on DOT4 and 5.1 specication uids. Uses 9V

battery (not included).

Model No: .....................................VS027.V2

Moisture Content:

Green: ...........................................<0.5%

Yellow: ........................................0.5 - 3.5%

Red: .............................................>3.5%

4.1. Battery Installation/Removal

4.1.1. Open the battery compartment in the rear of the tester (g.2).

4.1.2. Insert or remove 9V battery (PP3 or equivalent), observing correct polarity.

4.1.3. Close the battery compartment.

4.2. Calibration

4.2.1. Unfold the test bar.

4.2.2. Clean the two probes on the test bar head (g.3)

4.2.3. Dip the test bar head into a sample of uid drawn from a container which was previously unopened and sealed (g.3). This is particularly

important as this uid will used as the reference against which subsequent samples are compared.

4.2.4. Press and hold the test button and turn the reset screw anticlockwise fully (g.4). All the LED’s should now be unlit.

4.2.5. Turn the reset screw clockwise until the green LED lights. The calibration procedure is now complete.

g.2 g.3 g.4

VS027.V2 Issue:1 - 25/11/14

Original Language Version

g.1

5. OPERATION

NOTE: This tester is intended to provide a quick indication of the moisture content of brake uid. For a more precise measure we

recommend the use of a device which measures the boiling point of the uid, such as the sealey VS7021.

5.1. Unfold the test bar and dip the head into the brake uid reservoir.

5.2. Press the test button for ve seconds and observe the LED incications:

GREEN: Moisture content below 0.5%; brake uid good.

YELLOW: Moisture content between 0.5% and 3.5%; brake uid poor. Replacement is recommended. If uid is not replaced: a further

check with a device measuring brake uid boiling point is recommended.

RED: Moisture content above 3.5%. This should be regarded as an indication that the brake uid is unsafe and should be replaced.

5.3. IF IN ANY DOUBT - REPLACE THE BRAKE FLUID.

Battery Removal

See section 4.1. for battery removal details.

Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential

purchasers of products containing batteries (as dened within these regulations), that they are registered with Valpak’s

registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be

sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.

When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)

into approved containers and dispose of the product and the fluids according to local regulations.

WEEE Regulations

Dispose of this product at the end of its working life in compliance with the EU Directive on

Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed

of in an environmentally protective way. Contact your local solid waste authority for recycling information.

Inhaltsverzeichnis

Andere Sealey Prüfgeräte Handbücher

Sealey

Sealey TA120 Bedienungsanleitung

Sealey

Sealey BT91/7P Bedienungsanleitung

Sealey

Sealey Auto Service BT91D.V2 Bedienungsanleitung

Sealey

Sealey TST22 Bedienungsanleitung

Sealey

Sealey BT91/7.V4 Bedienungsanleitung

Sealey

Sealey VSE211.V4 Firmware-Update

Sealey

Sealey CV0011.V2 Bedienungsanleitung

Sealey

Sealey VS402 Bedienungsanleitung

Sealey

Sealey BT91/1.V2 Bedienungsanleitung

Sealey

Sealey AUTO SERVICE LINE TA125 Bedienungsanleitung

Sealey

Sealey BT2003.V5 Bedienungsanleitung

Sealey

Sealey CT955.V2 Bedienungsanleitung

Sealey

Sealey VS0033 Bedienungsanleitung

Sealey

Sealey TA320.V2 Bedienungsanleitung

Sealey

Sealey VS211 Bedienungsanleitung

Sealey

Sealey VS027.V3 Bedienungsanleitung

Sealey

Sealey BT2001 Bedienungsanleitung

Sealey

Sealey VS0061.V2 Bedienungsanleitung

Sealey

Sealey Auto Service Line TA131 Bedienungsanleitung

Sealey

Sealey BT105 Bedienungsanleitung

Sealey

Sealey VSE211.V3 Bedienungsanleitung

Sealey

Sealey VS2050 Bedienungsanleitung

Sealey

Sealey VS270 Bedienungsanleitung

Sealey

Sealey TA113 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung