Sealey VS2050 Bedienungsanleitung

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

INSTRUCTIONS FOR:

DIESEL INJECTION LEAK BACK

TEST KIT - PIEZO

MODEL No: VS2050

1. SAFETY INSTRUCTIONS

3. PARTS

2. INTRODUCTION

WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using this kit.

WARNING! Fuel is flammable - keep away from sources of ignition, including hot surfaces e.g. exhaust manifold.

DO NOT use the kit if any parts are missing or damaged.

DO NOT use the kit to perform a task for which it is not designed.

DO NOT allow untrained persons to use the kit.

DO NOT use when tired or under the influence of drugs, alcohol or intoxicating medication.

Switch off vehicle's ignition before commencing work under the bonnet.

Maintain the kit's components in good and clean condition for best and safest performance.

Wear eye protection and keep skin contact with fuel to a minimum. If fuel enters eyes rinse with plenty of water and seek medical

advice. If swallowed seek medical advice immediately. A full range of personal safety equipment is available from your Sealey dealer.

Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.

Keep children and other unauthorised persons away from the working area.

Ensure there is adequate lighting whilst using this kit.

Use approved parts only. Unapproved parts may be dangerous and will invalidate the warranty.

Keep work area clean and tidy and free from unrelated materials.

 If running the vehicle's engine in an enclosed space, ensure that there is sufficient ventilation or use an exhaust extraction system.

Dispose of waste fuel in accordance with local authority regulations.

When work on the vehicle is finished ensure that there are no tools or parts left in the engine compartment.

After use, clean equipment, return all contents to the case and store in a safe, dry, childproof location.

IMPORTANT: Always refer to the vehicle manufacturer's service instructions, or proprietary manual, to establish the current

procedures and

correct data.

Item Part No. Description

1 VS2050.01 Pressure Gauge (-1 to +3 bar) (Delphi)

2 VS2050.02 Pressure Gauge (-1 to +15 bar) (Bosch/Siemens)

3 VS2050.03 Main Body

4 VS2050.04 Injector Connector

5 VS2050.05 Injector Connector (angled)

Item Part No. Description

6 VS2050.06 Brass Cone (Delphi)

7 VS2050.07 Return Flow Connector (Brass end)

8 VS2050.08 Return Flow Connector

9 VS2050.09 Connectors (Delphi-brass cone)

10 VS2050.10 Connectors (Delphi-brass cone)

Specially designed to test the return flow fuel pressure from Piezo diesel common rail injectors on Bosch, Delphi and Siemens systems. Supplied

with two gauges, -1 to +3 bar and -1 to +15 bar. Sight-glass that identifies air in the fuel system and drain valve allows safe recovery of fuel.

Original Language Version VS2050 Issue: 1 - 24/03/10

4. OPERATION

NOTE:Before using the tester, inspect the adaptor connections

and return flow connections for obstructions, as these

could considerably increase the pressure in the injector,

possibly causing damage to it. Ensure that the fuel system

is NOT pressurised, refer to the vehicle manufacturer's

instruction manual.

4.1. Setting up the tester.

Fit one of the gauges to the main body, the 15 Bar gauge for

Bosch and Siemens systems and the 3 Bar gauge for Delphi

systems. Ensure that the drain valve is in the Off position.

4.1.1. Disconnect the return line to the injector that is to be tested.

4.1.2. Connect the return line to one of the return flow connectors and

connect the other end of the return flow connector to one of the

connectors on the main body of the tester.

4.1.3. Connect one of the injector connectors to the injector and the other

end of the injector connector to the other connector on the main

body.

4.1.4. If testing a Delphi system, use the brass cone for the return flow.

4.2. Testing an engine that will not start.

4.2.1. Briefly operate the starter motor several times so that the

transparent sight glass is filled with fuel.

4.2.2. Operate the starter motor for ten seconds, at the same time read

the pressure or vacuum reading on the gauge. Compare this

reading with the manufacturer's data and rectify problem if required.

4.3. Testing an engine that is running.

4.3.1. Start the engine and allow it to run at idling speed until the

transparent sight glass is filled with fuel.

4.3.2. Read the pressure or vacuum reading on the gauge. Compare this

reading with the manufacturer's data and rectify problem if required.

4.4. Removing tester.

4.4.1. Turn off the engine. To depressurise the fuel system, place the drain

pipe into a suitable container and open the drain valve. When all

fuel has drained out, close the drain valve. Dispose of the fuel

responsibly or re-use it.

4.4.2. Remove the connectors from the main body, disconnect the

connectors from the vehicle's fuel system and reconnect the return

line to the injector. Ensure all tools and kit parts are removed before

driving the vehicle.

Web

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

Sole UK Distributor, Sealey Group,

Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk,

IP32 7AR

Original Language Version VS2050 Issue: 1 - 24/03/10

01284 757500

01284 703534

sales@sealey.co.uk

www.sealey.co.uk

Andere Sealey Prüfgeräte Handbücher

Sealey

Sealey VS0275.V2 Bedienungsanleitung

Sealey

Sealey BT2002 Bedienungsanleitung

Sealey

Sealey Auto Service VS0271 Bedienungsanleitung

Sealey

Sealey BT91/7.V3 Bedienungsanleitung

Sealey

Sealey BT91/10 Bedienungsanleitung

Sealey

Sealey TA301 Bedienungsanleitung

Sealey

Sealey BT105 Bedienungsanleitung

Sealey

Sealey BT2002.V2 Bedienungsanleitung

Sealey

Sealey TA120 Bedienungsanleitung

Sealey

Sealey VSE953 Bedienungsanleitung

Sealey

Sealey VSE2020.V3 Bedienungsanleitung

Sealey

Sealey BT102.V2 Bedienungsanleitung

Sealey

Sealey VS2030.V2 Bedienungsanleitung

Sealey

Sealey PP100.V2 Bedienungsanleitung

Sealey

Sealey TA120 Bedienungsanleitung

Sealey

Sealey TA130 Bedienungsanleitung

Sealey

Sealey AUTO SERVICE VSE206 Bedienungsanleitung

Sealey

Sealey HBS971 Bedienungsanleitung

Sealey

Sealey PPHY Bedienungsanleitung

Sealey

Sealey VS2030.V2 Bedienungsanleitung

Sealey

Sealey CV0011 Bedienungsanleitung

Sealey

Sealey TA126 Bedienungsanleitung

Sealey

Sealey VSE300D Bedienungsanleitung

Sealey

Sealey CV2030 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung