Sealey VS027.V3 Bedienungsanleitung

BRAKE FLUID TESTER

MODEL NO: VS027.V3

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

1.1. GENERAL SAFETY

8 DO NOT use the tester to perform a task for which it is not designed.

8 DO NOT allow untrained persons to use the tester.

8 DO NOT use whilst under the inuence of drugs, alcohol or intoxicating

medication.

9 Keep children and unauthorised persons away from the work area.

9 Keep work area clean and tidy and free from unrelated materials.

9 Ensure the work area has adequate lighting.

9 After use, clean equipment and store in a cool, dry, child proof area.

 WARNING!Brake uid is ammable - keep away from sources of

ignition, including hot surfaces e.g. exhaust manifold.

1.2. BRAKE FLUID SAFETY

 WARNING!Brake uid will damage paintwork. Any spillage should be

ushed with water immediately.

9 Always read and comply with the warnings on the brake fluid container.

9 Wear eye protection and keep skin contact to a minimum. If brake fluid

enters eyes rinse with plenty of water and seek medical advice.

9If swallowed seek medical advice immediately.

9Dispose of waste fluid in accordance with local authority regulations.

2. INTRODUCTION

Comparative electrolytic type tester. Checks moisture content of uid by resistance to electric current. Easily calibrated using new brake uid.

Audible test cycle with three LED read-out. Just insert probe and press button for immediate result. Works on DOT4 and 5.1 specication uids.

Uses 9V battery (not included).

3. SPECIFICATION

Model No: .....................................VS027.V3

Moisture Content:

Green: ...........................................<0.5%

Yellow: ........................................0.5 - 3.5%

Red: .............................................>3.5%

4. PREPARATION

4.1. Battery installation

4.1.1. Open battery compartment at back of tester, g.2 and insert PP3 or equivalent observing correct polarity.

4.2. Calibration

4.2.1. Unfold the test bar.

4.2.2. Clean the two probes on the test bar head (g.3)

4.2.3. Dip the test bar head into a sample of uid drawn from a container which was previously unopened and sealed (g.3). This is

particularly important as this uid will used as the reference against which subsequent samples are compared.

4.2.4. Press and hold the test button and turn the reset screw anticlockwise fully (g.4). All the LED’s should now be unlit.

4.2.5. Turn the reset screw clockwise until the green LED lights. The calibration procedure is now complete.

VS027.V3 | Issue:1 27/02/18

Original Language Version

Refer to

instruction

manual

Wear eye

protection

Wear

protective

gloves fig.1

fig.2

fig.3

fig.4

5. OPERATION

NOTE: This tester is intended to provide a quick indication of the moisture content of brake uid. For a more precise measure we

recommend the use of a device which measures the boiling point of the uid, such as the Sealey VS0271 or VS0275.

5.1. Unfold the test bar and dip the head into the brake uid reservoir.

5.2. Press the test button for ve seconds and observe the LED indications:

GREEN: Moisture content below 0.5%; brake uid good.

YELLOW: Moisture content between 0.5% and 3.5%; brake uid poor. Replacement is recommended. If uid is not replaced: a further

check with a device measuring brake uid boiling point is recommended.

RED: Moisture content above 3.5%. This should be regarded as an indication that the brake uid is unsafe and should be

replaced.

5.3. IF IN ANY DOUBT REPLACE THE BRAKE FLUID.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to

a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely

unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids

according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior

notice.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

BATTERY REMOVAL REFER TO 4.1

Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products

containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack

Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.

VS027.V3 | Issue:1 27/02/18

Original Language Version

Inhaltsverzeichnis

Andere Sealey Prüfgeräte Handbücher

Sealey

Sealey VS4021 Bedienungsanleitung

Sealey

Sealey BT3000 Bedienungsanleitung

Sealey

Sealey VS0275.V2 Bedienungsanleitung

Sealey

Sealey VSE211.V4 Firmware-Update

Sealey

Sealey BT105 Bedienungsanleitung

Sealey

Sealey VSE3158 Bedienungsanleitung

Sealey

Sealey BT2013.V4 Bedienungsanleitung

Sealey

Sealey VS0031.V3 Bedienungsanleitung

Sealey

Sealey VSE210 Bedienungsanleitung

Sealey

Sealey BT2003.V4 Bedienungsanleitung

Sealey

Sealey BT91/11 Bedienungsanleitung

Sealey

Sealey VS2058.V2 Bedienungsanleitung

Sealey

Sealey BT102.V2 Bedienungsanleitung

Sealey

Sealey VSE300D Bedienungsanleitung

Sealey

Sealey VSE2020.V2 Bedienungsanleitung

Sealey

Sealey VS0012 Bedienungsanleitung

Sealey

Sealey BT2011 Bedienungsanleitung

Sealey

Sealey BT01 Bedienungsanleitung

Sealey

Sealey VS2030.V2 Bedienungsanleitung

Sealey

Sealey VS4022.V2 Bedienungsanleitung

Sealey

Sealey HBS97.HGV Bedienungsanleitung

Sealey

Sealey BT2101 Bedienungsanleitung

Sealey

Sealey BT2013.V5 Bedienungsanleitung

Sealey

Sealey VS0033 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung