Sealey AP2010.V2 Bedienungsanleitung

HARDWOOD TOP WORK BENCH

MODEL NO: AP2010.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

MPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGEAND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY

1.1 GENERAL SAFETY

WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this bench.

9Locate bench in a suitable working area.

9Keep the work area clean, uncluttered and ensure there is adequate lighting.

WARNING! Use bench on level and solid ground, preferably concrete. Avoid tarmacadam since the bench may sink into the surface.

9Keep the bench clean and tidy in accordance with good workshop practice.

9Keep children and unauthorised persons away from the working area.

8DO NOT use the bench for any purpose other than that for which it is designed.

8DO NOT undertake work on the bench without the work-piece being adequately secured. Use clamps or a vice (not included) to secure

the work-piece. Available from your Sealey Stockist.

8DO NOT use the bench outdoors.

8DO NOT get the bench wet or use in damp or wet locations or areas where there is condensation.

8DO NOT clean the bench with any solvents which may damage the paint surface or the protective coating on the wooden top.

2. INTRODUCTION

Powder coated steel panels with 40mm wood laminate top. Features lockable cupboard with 6-pin tumbler lock and two keys. Supplied at

packed.

2.1. Carefully unpack the product and check the contents against the diagram below. Should any items be missing or damaged make

immediate contact with your Sealey dealer.

AP2010.V2 Issue 1 (HF) 26/06/18

Original Language Version

Refer to

instructions

3. ASSEMBLY

3.1. Take one cross-rail (B) and one cross-rail (D) and bolt them to the cabinet sides (A) using the self tapping screws (O). Ensure that the pairs of

holes that accept the corner braces are facing downwards. ( Refer to STEP 8.)

3.2. Bolt centre support (C) to the rear lower cross-rail (B) and front centre support (E) to the front lower cross-rail (D) using the self tapping (O).

3.3. Bolt inner shelf supports (G) to the centre supports and right hand side panel using the self tapping screws (O). Leave out top bolt on rear

centre support until back panel is required in STEP 5.

3.4. Bolt into position rear cross-rail (B). Take door (J) and drop lower hinge pin into the hole in lower cross rail. Hold door in position and bolt in

place front cross-rail (D) ensuring that the upper hinge pin has entered the hinge hole in underside of cross-rail. You will need the self tapping

screws (O).

3.5. Bolt the two back wall panels (F) to the rear of the cabinet using the self tapping screws (O).

3.6. Bolt the two shelf parts (H) into the left hand compartment of the cabinet using the self tapping screws (O).

AP2010.V2 Issue 1 (HF) 26/06/18

Original Language Version

3.7. Place the wooden top (N) face down on a flat, clean, smooth surface. Place the cabinet upside down on the wooden top and align it with the four

pre-drilled holes. Fix with the four hex head screws (S). Screw into place the four adjustable leg levellers (R).

3.8. Bolt the four corner braces (I) into place using the self tapping screws (O), 16 lock washers (P), and 16 nuts (Q).

3.9. Bolt one shelf part (K) to the underside of the cupboard compartment as indicated above using the self tapping screws (O). Tighten all fixings

and turn workbench the right way up.

3.10. Put shelf component (K) into place at desired height inside cupboard.

Place the finished workbench in its final location and adjust the leg levellers so that the bench is both level and stable in use.

AP2010.V2 Issue 1 (HF) 26/06/18

Original Language Version

AP2010.V2 Issue 1 (HF) 26/06/18

Original Language Version

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to

a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely

unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids

according to local regulations.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior

notice.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Inhaltsverzeichnis

Andere Sealey Werkzeugaufbewahrung Handbücher

Sealey

Sealey API Series Bedienungsanleitung

Sealey

Sealey AP4206BE Bedienungsanleitung

Sealey

Sealey CX313.V2 Bedienungsanleitung

Sealey

Sealey AP1640 Bedienungsanleitung

Sealey

Sealey API16 Bedienungsanleitung

Sealey

Sealey SL1D.V2 Bedienungsanleitung

Sealey

Sealey AP28104 Bedienungsanleitung

Sealey

Sealey SC01.V2 Bedienungsanleitung

Sealey

Sealey AP2416 Bedienungsanleitung

Sealey

Sealey AP1248SS.V2 Bedienungsanleitung

Sealey

Sealey API1500 Bedienungsanleitung

Sealey

Sealey AP26059TW Bedienungsanleitung

Sealey

Sealey AP41104BWS Bedienungsanleitung

Sealey

Sealey AP1100M Bedienungsanleitung

Sealey

Sealey AP22DFC Bedienungsanleitung

Sealey

Sealey AP2200BB Series Bedienungsanleitung

Sealey

Sealey SM30.V2 Bedienungsanleitung

Sealey

Sealey AP6310.V2 Bedienungsanleitung

Sealey

Sealey PTB66004SS Bedienungsanleitung

Sealey

Sealey TS01 Bedienungsanleitung

Sealey

Sealey PTB141507 Bedienungsanleitung

Sealey

Sealey AP2405 Bedienungsanleitung

Sealey

Sealey AP4804SS Bedienungsanleitung

Sealey

Sealey PTB66004 Bedienungsanleitung

Beliebte Werkzeugaufbewahrung Handbücher anderer Marken

Ryobi

Ryobi RWB03 Bedienungsanleitung

Husky

Husky H27CH5TR4BGK Bedienungsanleitung

Scheppach

Scheppach ts 2100 Bedienungsanleitung

Cornwell Tools

Cornwell Tools CTB360AKBK Bedienungsanleitung

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Bedienungsanleitung

Cassese

Cassese CS200 CART Bedienungsanleitung

Kendall Howard

Kendall Howard ESDW-9630-1000 Bedienungsanleitung

Lista

Lista Align Montageanleitung

Workzone

Workzone 99609 Bedienungsanleitung

Stanley

Stanley STST83800-1 Bedienungsanleitung

Homak

Homak PROFESSIONAL Series Systemhandbuch

Perel

Perel ROLLER SHUTTER STORAGE CABINET Bedienungsanleitung

Husky

Husky H5CH2R Bedienungsanleitung

BGS technic

BGS technic 4107 Bedienungsanleitung

Clarke

Clarke CWB1250 Bedienungsanleitung

Ryobi

Ryobi RWB02 Bedienungsanleitung

Husky

Husky H52CH6HDV3WHT Bedienungsanleitung

General International

General International Excalibur 40-100 Stücklistenhandbuch