Securitytronix ST-IP-MD36-1 Bedienungsanleitung

ST-IP-MD36-1

ST-IP-MD36-2

HD Mini Network Dome Camera Quick Start Guide

Version 1.0.0

Welcome

Thank you for purchasing our Networkcamera.

This Quick Start Guide is designed to get yoursystem up and running as easily as possible.

This document applies to both the ST-IP-MD36-1 and ST-IP-MD36-2 camera models (1mp &

2mp).

Please read the following safeguard and warnings carefully before you use this camera.

Please keep this document for futurereference.

Important Safeguards and Warnings

1．Electrical safety

All installation and operation should conform to your local electrical safetycodes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the

Limited power source is rated 12V DC, DC5V or AC24V in the IEC60950-1. (Power supply

requirement is subject to the devicelabel).

Please prevent the line cord from being crushed or damaged, especially at the plug, power

socket and the junction from the device.

Note: Do not connect a PoE power source AND a power supply to the device at the same

time; it may result in device damage.

We assume no liability or responsibility for fires or electrical shock caused byimproper

handling or installation.

We are not liable for any problems caused by unauthorized modification or attemptedrepair.

2．Environment

Don’t aim the device at strong light (such as lighting, sunlight and so on) to focus;

otherwise it may cause overexposure, which will affect the longevity of the CCD or CMOS

imager.

Please transport, use and store the device within the range of allowed humidity and temperature.

Don’t keep the device in a place which is wet, dusty, extremely hot, and extremely cold and with

strong electromagnetic radiation or unstablelighting.

Please do not allow water and other liquids to enter the camera, to prevent the internal

components from being damaged.

Please allow adequate ventilation around the camera to prevent heataccumulation.

Please pack the device with the standard factory packaging or material with the same

quality when transporting the device.

Avoid bumps and humidity during transportation, storage and installation.

3. Operation and Daily Maintenance

Please do not dismantle the device; Doing so may void your warranty.

It is recommended to use this camera with a surge-protection device.

The grounding holes of the product are recommended to be grounded to further enhance the

reliability of the camera.

Do not touch the CCD (CMOS) optic component directly. You can use an air blower to clean

the dust or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the

dust gently if it is necessary to clean.

Always use a dry, soft cloth to clean the device. If there is too much dust, please use the water to

dilute mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the

device. Don’t use volatile solvents like alcohol, benzene, thinner etc or strong detergents with

abrasiveness, otherwise it will damage the surface coating or reduce the working performance of

the device.

The dome cover is an optical device, please don’t touch or wipe cover surface directly during

installation and use, please refer to the following methods to clean a dirty lens:

Stained with dirt:

Use an oil-free soft brush to gently remove it.

Stained with grease or fingerprints:

Use a soft cloth to wipe the dome gently to dry it, then use oil-free cotton cloth or paper soaked

with alcohol or detergent to wipe from the lens center to outward. It is ok to change the cloth and

wipe several times to get all of the dirt off.

Warning

Please use the standard accessories provided by SecurityTronix and make sure the device is

installed and repaired by professional engineers.

Please do not provide two or more power supply modes for the device, otherwise it may cause

damage to the device.

Statement

Please refer to the actual product for more details; this manual is just forreference.

Please contact the supplier or customer service if there is any problem occurred when using the

device.

Please contact the customer service for the latest procedure and supplementary documentation.

There may be deviation between the actual value of some data and the value provided in the

manual due to the reasons such as the real environment is not stable and so on. Please refer to

the company’s final explanation if there is any doubt ordispute.

The company is not liable for any loss caused by operation which is inconsistent with the

instructions in the manual.

Note:

Please refer to the disk for more details. Check and download corresponding user’s manuals

and tools from the SecurityTronix website: http://www.securitytronix.com/support/

Before installation, please open the package and ensure all the components areincluded.

Contact your local retailer ASAP if something is broken in yourpackage.

Accessory Name Amount

Network Camera Unit 1

Installation Accessories bag

Quick Start Guide 1

CD 1

Table of Contents

Framework.........................................................................................................................5

1.1

Structure..............................................................................................................5

1.2

Dimensions..........................................................................................................6

Installation.........................................................................................................................8

2.1

Device Installation..............................................................................................8

2.2

Micro SD Card Installation................................................................................9

Network Configuration...................................................................................................11

3.1

Modify IP Address............................................................................................11

3.2

Physical Properties

1.1 Structure

Note:

The following diagram is for reference only, to illustrate the device component and cable port

functions.

Device component and cable port function may differ according to different models, please refer

to the actual device for details.

Figure 1-1

Please refer to the following sheet for detailed structureinformation.

Component

Component name

1 X-Y-Z rotation module

2 Device lens

3 Dome camera enclosure

Please refer to the following sheet for detailed portinformation.

Port Port name Function

Power input port Connect to a 12VDC power supply

Network port

Network data input, output and

PoE.

Note:

Some devices do not support

PoE.

6 MIC hole Audio input

1.2 Dimensions

Please refer to the following figure for the dimension information. Dimensions are listed in

millimeters. See Figure 1-1 through Figure 1-3.

Figure 1-1 Dimension illustration1

Figure 1-2 Dimension illustration2

Figure 1-3 Dimension illustration 3

Installation

2.1 Device Installation

Figure 2-1 Device installation illustration 1

Important

Please make sure the installation surface can support at least 3 times the weight of the

camera and the bracket.

Please refer to the steps listed below.

Step1

Use the inner hexagonal wrench (provided) to loosen the three inner hexagon screws in the

outer dome cover and then remove the cover.

Step 2

Locate the installation template in the accessories bag, and affix it to the ceiling or wall

according to your monitor arearequirements.

Step 3

Drill 3 holes, 3/16” diameter as indicated at the marks on the template. Remove the template

and insert the 3 included plastic expansion anchors in the holes.

Note:

If the cable must exit behind the installationsurface (behind a wall or inside the ceiling),

Drill a ¾” cable exit hole in the mounting surface according to the installation template.

If the cable must exit the camera on the surface of the wall or ceiling, use a strong needle-

nose plier or similar tool to pry out and remove the thin metal of the camera’s outer shell, as

shown in Figure 2-1 above; “Remove this for surface-cable use”.

Remove this for surface-cable use

Step 4

Adjust the base of the camera to the proper position and then pull the cable through the cable

exit hole drilled earlier in the ceiling or wall. Line up the TOP direction of the device to the

installation template and then line up the three screw holes in the camera’s base to the three

plastic anchors in the mounting surface. Install the three self-tapping screws firmly into the

anchors.

Step 5

Use the ‘inner hexagonal wrench’ to loosen the two screws which secure the lens rotation

structure NOTE: Do not remove these screws. Only loosen them enough for the camera

housing to move freely to the correct viewing position. Adjust the lens to the required

viewing angle, then secure the screws of the lens rotation structure. The lens adjust angle

ranges are: flip (0°~+75°), video pan rotation (-15°~+15°), video rotation angle(-15°~+15°).

Figure 2-2 Device installation illustration 2

Step 6

Line up the dome camera cover to the cable exits and reinstall the cover. Use the inner

hexagonal wrench to secure the three inner hexagonal screws firmly.

Note:

If you want to restore the factory default settings of the camera, remove the outer cover and

press and hold the Reset button in Figure 2-2 with power on for10s.

2.2 Micro SD Card Installation

Note:

This model of camera does not support Micro SD card functions.

Step 1

Open the camera by referring to step 1 in chapter 2.1 deviceinstallation.

Step 2

Find the “Micro SD CARD” mark on the inner cover, adjust the direction of Micro SD cardand

complete installation according to the location shown in the Figure3-3.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Securitytronix Sicherheitskamera Handbücher

Securitytronix

Securitytronix ST-BTWD600IR40-B Bedienungsanleitung

Securitytronix

Securitytronix ST-D420IR6-B Bedienungsanleitung

Securitytronix

Securitytronix ST-DLI6502812-JBX-B Bedienungsanleitung

Securitytronix

Securitytronix ST-PTZMINI-IR10XTA Bedienungsanleitung

Securitytronix

Securitytronix ST-HDC2FB Bedienungsanleitung

Securitytronix

Securitytronix ST-IP4VFD-MZL Bedienungsanleitung

Securitytronix

Securitytronix ST-BT650IRVFDV –B Bedienungsanleitung

Securitytronix

Securitytronix ST-DWD600IRVP2812-B Bedienungsanleitung

Securitytronix

Securitytronix ST-BT800P-W Bedienungsanleitung

Securitytronix

Securitytronix ST-IP2VFB Bedienungsanleitung

Securitytronix

Securitytronix ST-IP2FWD Bedienungsanleitung

Securitytronix

Securitytronix ST-D600VP3.6-B-W Bedienungsanleitung

Securitytronix

Securitytronix ST-LCDHD-18.5 Bedienungsanleitung

Securitytronix

Securitytronix ST-D420IR3.6 Bedienungsanleitung

Securitytronix

Securitytronix ST-IP-DVF-1 Bedienungsanleitung

Securitytronix

Securitytronix ST-CVTMD420-WPIR-W Bedienungsanleitung

Securitytronix

Securitytronix ST-PTZ480-22 Bedienungsanleitung

Securitytronix

Securitytronix ST-WD600PTZMINI-IR Bedienungsanleitung

Securitytronix

Securitytronix ST-D650IRVP-B Bedienungsanleitung

Securitytronix

Securitytronix ST-DWD700-3.6-B Bedienungsanleitung

Securitytronix

Securitytronix HD-COAXINATORTVI ST-HDC2PTZ Bedienungsanleitung

Securitytronix

Securitytronix ST-PTZ480-22X Bedienungsanleitung

Securitytronix

Securitytronix ST-BT1000IRVFDV-B Bedienungsanleitung

Securitytronix

Securitytronix ST-IP-BT3.6-1 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung