Securitytronix ST-IP2PTZ Bedienerhandbuch
ST-IP2PTZ
QUICK START GUIDE
www.nacebrands.com www.securitytronix.com
ST-IP2PTZ QUICK START GUIDE
1
Thank you for purchasing our product. If there are any questions, or requests, please do
not hesitate to contact the dealer.
This manual applies to the ST-IP2PTZ network speed dome camera.
This manual may contain several technical incorrect places or printing errors, and the
content is subject to change without notice. The updates will be added to the new
version of this manual. We will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of
the security or signaling aspects of this product. UL has only tested for fire, shock or
casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or signaling aspects of this
product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
ST-IP2PTZ QUICK START GUIDE
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits
for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at their own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot
be disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
ST-IP2PTZ QUICK START GUIDE
3
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
All the electronic operations should be in strict compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter that is originally included. The power adapter standard
is 24VAC10%, 12VDC10% or 48VDC (PoE) (depending on models). The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heating or a fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the speed dome.
When the product is installed on a wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact technical support.
If the product does not work properly, please contact your dealer or technical support.
Never attempt to disassemble the speed dome yourself. (Securitytronix shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Cautions
Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetic radiation. Avoid equipment installation on vibrating surface or places
subject to shock (ignoring this can cause equipment damage).
Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire
or electrical shock may occur. The operating temperature should be -22°F ~ 149°F.
The dome cover for indoor use shall be kept from rain and moisture.
Warnings Follow these safeguards
to prevent serious injury or death.
Cautions Follow these precautions
to prevent potential injury or
material damage.
ST-IP2PTZ QUICK START GUIDE
4
Exposing the equipment to direct sun light, low ventilation or heat sources such as
heaters or radiators is not advisable (ignoring this may cause a fire hazard).
Do not aim the speed dome at the sun or extra bright places. A blooming or smear
may occur otherwise (which is not a malfunction), and affecting the longevity of the
sensor at the same time.
Please use the provided glove when opening up the dome cover, avoid direct contact
with the dome cover with bare hands, due to the the acidic sweat of the fingers
eroding the surface of the dome cover.
Please use a soft and dry cloth when cleaning inside and outside surfaces of the dome
cover, do not use alkaline detergents.
Please keep all wrappers after unpacking them for future use. In case any failure
occurs, you need to return the speed dome to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the speed dome
and may lead to additional costs.
Do not stare directly at the infrared LED to avoid possible damage to the eyes.
ST-IP2PTZ QUICK START GUIDE
5
Table of Contents
1 Overview ...................................................................................................... 6
2 Installation ................................................................................................... 7
3 Setting the Network Dome over the LAN...................................................... 9
4 Accessing via Web Browser ........................................................................ 12
ST-IP2PTZ QUICK START GUIDE
6
1Overview
Please make sure the power to the speed dome has been disconnected before
connecting the cables.
The cable interfaces of the network speed dome are shown in the following figure. The
cables are distinguished by different colors. The labels attached on the cables are for
identification.
Figure 1-1 Overview
Table 1-1 Overview
No.
Description
1
Power Cable
2
Network Cable
1
2
ST-IP2PTZ QUICK START GUIDE
7
2Installation
Before you start:
Check the package contents and make sure that the device in the package is in good
condition and all the assembly parts are included.
Please make sure the wall is strong enough to withstand more than 8 times the
weight of the dome and the mount.
For a cement wall, you need to use the expansion screws to fix the mount.
Note: Do not drag the speed dome with its waterproof cables as shown in Figure 1-1,
otherwise the waterproof performance will be affected.
Figure 1-1 Do Not Drag the Cables
Steps:
1. Remove the protective sticker from the dome drive.
Figure 2-1 Protective Sticker
2. Drill 4 screw holes in the wall according to the holes of the mount.
3. Secure the wall mount to the wall with the M8 expansion screws.
Protective
Sticker
ST-IP2PTZ QUICK START GUIDE
8
Figure 2-2 Secure the Mount
4. Install the speed dome to the mount.
1). Hang the safety rope to the speed dome and then hook to the mount as shown in
Figure 2-3.
2). Route the cables of the speed dome through the wall mount.
3). Loosen the two lock screws on the wall mount.
4). Install the speed dome to the mount, and secure the speed dome by rotating the
speed dome clockwise.
5). Secure the two lock screws with the Allen wrench.
Figure 2-3 Secure the Speed Dome
Safety Rope
Lock
Screw
ST-IP2PTZ QUICK START GUIDE
9
3Setting the Network Dome over the LAN
To view and configure the speed dome via LAN (Local Area Network), you need to
connect the network speed dome in the same subnet as your PC. Then install the SADP
or the client software to search and change the IP of the network speed dome.
The following figure shows the cable connection of network speed dome to PC.
Figure 3-1 Wiring over LAN
Set the IP address of the speed dome for accessing via LAN.
Steps:
1. To get the IP address, you can choose either of the following methods:
Use SADP, a software tool which can automatically detect the network speed
dome in the LAN and list the device information like IP address, subnet mask, port
number, device serial number, device version, etc., shown in Figure 3-2.
Use client software to list the online devices. Please refer to the user manual of
client software for detailed information.
2. Change the IP address and subnet mask to the same subnet as your PC.
Refer to the following introductions to set the IP address with SADP software:
Search active devices online
Search online devices automatically:
After launching the SADP software, it automatically searches the online devices
every 15 seconds from the subnet where your computer is located. It displays the
total number and information of the searched devices in the Online Devices
interface. Device information including the device type, IP address, port number,
gateway, etc. will be displayed.
Speed Dome
Switch
Network
PC
NVR
Inhaltsverzeichnis
Andere Securitytronix Sicherheitskamera Handbücher
Securitytronix
Securitytronix ST-BT1000IR2812-G Bedienungsanleitung
Securitytronix
Securitytronix HD-Coaxinator ST-HD-BT2812-720-G Bedienungsanleitung
Securitytronix
Securitytronix ST-PTZ650FM-23X Bedienungsanleitung
Securitytronix
Securitytronix ST-PTZMINI-IR10XTA Bedienungsanleitung
Securitytronix
Securitytronix ST-D600IRVP2812 Bedienungsanleitung
Securitytronix
Securitytronix ST-D700IR2812-B/W Bedienungsanleitung
Securitytronix
Securitytronix HD-Coaxinator ST-HD-BT2812-1MP Bedienungsanleitung
Securitytronix
Securitytronix ST-PTZIR530-36 Bedienungsanleitung
Securitytronix
Securitytronix ST-BT540IR30VF Bedienungsanleitung
Securitytronix
Securitytronix ST-PTZ550-27 Bedienungsanleitung
Securitytronix
Securitytronix ST-D540IRVP49-S Bedienungsanleitung
Securitytronix
Securitytronix ST-DLI600VPDV2812-B-W Bedienungsanleitung
Securitytronix
Securitytronix ST-D600IR2812-HB Bedienungsanleitung
Securitytronix
Securitytronix ST-IP-DVF-1 Bedienungsanleitung
Securitytronix
Securitytronix HD-COAXINATOR TVI ST-HDC2FB-CNV Bedienungsanleitung
Securitytronix
Securitytronix HD-CoaxinatorTVI ST-HDC2VFB-MZ Bedienungsanleitung
Securitytronix
Securitytronix ST-DWD700-3.6-B Bedienungsanleitung
Securitytronix
Securitytronix ST-D600IR2812-DSHB Bedienungsanleitung
Securitytronix
Securitytronix ST-DLI6502812-JBX-B Bedienungsanleitung
Securitytronix
Securitytronix TVI-AC344-MB Bedienungsanleitung
