Securitytronix ST-PTZIR480-22X Bedienungsanleitung

INSTALLATION MANUAL©

ST-PTZIR480-22X

High-Speed Intelligent Dome

IR PTZ Color Camera

PACKAGE CONTENTS

This package contains:

One ST-PTZIR480-22X high-speed intelligent dome color camera.

One mounting bracket.

One 24VAC 3A power supply.

One installation manual.

PRODUCT DESCRIPTION

The ST-PTZIR480-22X is a professional grade infrared intelligent dome color camera with pan, tilt and zoom (PTZ)

capability and 480TVL resolution. The camera’s non-volatile digital memory allows the saving of all settings. Its

200 preset positions provide versatility for cruise routes and tour functions. The ST-PTZIR480-22X’s mechanical

design permits continuous horizontal 360°rotation and 90°vertical flip. Temperature management is built-in.

Functions and Features

Non-volatile design ensures data will not be lost if power fails.

Recovery function allows the camera to continue previous functions after power is restored.

Support for 200 presets and 4 preset tours, each containing up to 32 presets.

4 patterns, each can be recorded for 1000 discrete PTZ controller moves.

Support for 4-auto scans.

Soft and hard ID settings can be edited on the DIP switch or via the OSD menu.

Integrated multi-protocol control: PELCO“P”, PELCO“D”.

2 ch alarm input; 2 ch alarm relay output.

Proportional zoom lens; P/T speed will decrease in proportion with depth of zoom.

Can be installed indoors or outdoors.

Horizontal pan speed 0.5º-82º/s.

Vertical tilt speed 0.5º-30º/s.

360º continuously horizontal rotation.

Complies with IP 66/CE standard.

Built-in surge protection circuitry.

Auto focus, manual priority.

Auto iris.

Auto shift from Color to B/W.

Built-in OSD makes it easy to configure all settings of the camera.

Built-in display for the internal dome temperature, preset status and compass direction.

330ft IR distance for long-range surveillance.

SPECIFICATIONS

ST-PTZIR480-22X

Specifications (Typical)

1. Image Sensor Samsung SDM-270 with ¼” SONY CCD

2. Resolution 480TVL

3. Lens Auto Iris; F=3.5 to 94.5mm; 22X Optical Zoom, 10X Digital Zoom

4. Illumination 0.1 Lux

5. Pan Range 360º continuous

6. Tilt Rotation Range 0º - 90º flip

7. Manual Speed Pan 0.1º - 82º/sec

8. Manual Speed Tilt 0.1º - 30º/sec

9. Preset Speed 82º/sec

10. Preset Accuracy ±0.10°

11. Preset Positions 200

12. Function Display Yes

14. Pan & Tilt Position Display Yes

15. MAX IR Distance 330ft

19. Patterns 4 programmable (pan/tilt/zoom and each tour is 120 seconds)

20. Sequences (Tours) 4 programmable (dwell time speed preset point)

21. Protocol Pelco-D, Pelco-P selectable

22. Auto Scan With programmable variable speed

23. High Efficient 3-Dimension Scan Yes

24. Long-Focus Speed Limited Yes

26. Home Position Yes

27. Camera Menu Operation Yes

28. IP66 for Outdoor Use Yes

29. Operating Humidity ≤95%

30. Heater Operation 42ºF on; 57ºF off

31. Operating Temperature -40ºF - 122ºF

32. Video Connection BNC coaxial

33. Power 24VAC @3A, 35W

34. Communication RS485

Dimensions

Wall Mount Dimension

Picture 2

6 ½”

7 ¾”

5 ¼” 5 ½”

6”

10 1/8”

4 1/8”

6”

4 1/8”

6 1/8”

3 ¾”

5 ½”

INSTALLATION AND OPERATION

CAUTION: To reduce the risk of electrical shock do not remove the cover or back of this unit. No user

serviceable parts are inside.

CAUTION: To prevent electric shocks and risk of fire hazards, do not use other than specified power

source.

1. UNPACKING and HANDLING

Each unit is shipped partially assembled factory tested.

Ensure that all accessories are removed from the container before discarding packing materials.

a. Use the mounting arm as a template to mark the holes for your mounting hardware.

This symbol is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions.

This symbol is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electrical shock.

b. Feed the cable assembly up through the smaller end of the mount and out the rear opening.

c. Assemble the camera dome to the mounting arm using the 4 supplied allen-head cap screws and allen

wrench.

2. MECHANICAL INSPECTION

Inspect the entire camera for shipping damage. Make sure the equipment is clean, and no connectors are

broken, damaged, or loose. If equipment appears to be damaged or defective please contact your distributor

or SecurityTronix at 1-610-429-1511 for assistance.

3. SPECIAL ATTENTION

a. The installer must comply with electrical safety standards. There must be sufficient space between the

camera’s power supply and video line and any high voltage equipment and/or cables.

b. To help ensure the camera’s life and proper operation do not point the camera towards the sun or

strong light.

c. Do not install the camera in an environment where the temperature is above 122°F.

d. Do not install the camera near a magnetic field or a high-power motor.

e. Do not mount the camera near a radiator or heater.

f. The installation site and material must fully support the weight of the product.

g. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe gently with a mild

detergent. Never use strong or abrasive detergents.

h. The included 24VAC at 3A power supply must be used. Using a DC or other incorrect power supply

will damage the camera.

i. Only qualified installers are allowed to install, test and disassemble the camera.

j. The camera is a low voltage product. If installed outdoors proper safety and lightning grounding are

required.

k. Before installing be sure the grounding, wiring, input power, voltage, DIP switches, communication

protocol and baud rate are correctly set prior to powering up and using.

4. CAMERA SETUP

BAUD RATE & PROTOCOL SETUP

DIP Switch Settings

Baud rate Setting SW2（B7~B8）

Protocol Setting SW2（B1~B2）

DOME ADDRESS SETUP

System Setup DIP Switch SW1 ON = 1 OFF = 0

V2.0 7-31-12

5. WIRING CONNECTIONS

6. FUNCTIONS and OPERATION

Menu Operation

Several functions can be accessed directly without using the camera’s on screen menu display.

Note the following dedicated preset functions:

Special Use Preset Numbers

Call PRESET 95 ―― Enter into main OSD menu

Call PRESET 96 ―― Run pattern 1

Call PRESET 97 ―― Run Sequence 1

Call PRESET 92 ―― Set Left limit point for L/R scan

Call PRESET 93 ―― Set Right limit point for L/R scan

Call PRESET 99 ―― Run Left-right scan

•NOTE: If Left limit point and Right limit point are set to the same position, calling preset 99

will execute a 360° scan.

Call PRESET 33 ―― Swing 180°

Call PRESET 34 ―― Return to Zero point

The on screen menu provides access to all camera functions through the use of a standard RS485

connection and PTZ controller.

As shown above, use the PTZ controller to CALL PRESET 95 and the camera’s OSD menu will

appear overlaid upon the video output of the camera, as shown below.

Inhaltsverzeichnis

Andere Securitytronix Sicherheitskamera Handbücher

Securitytronix

Securitytronix ST-BTLI540IR30-B Bedienungsanleitung

Securitytronix

Securitytronix ST-HDC2FB Bedienungsanleitung

Securitytronix

Securitytronix ST-BTWD600IR2812 B Bedienungsanleitung

Securitytronix

Securitytronix ST-IP2FTD Bedienungsanleitung

Securitytronix

Securitytronix HD-CoaxinatorTVI ST-HDC2VFB-MZ Bedienungsanleitung

Securitytronix

Securitytronix ST-DLI600VP3.6-B-W Bedienungsanleitung

Securitytronix

Securitytronix HD-COAXINATOR TVI ST-HDC2FB-CNV Bedienungsanleitung

Securitytronix

Securitytronix ST-PTZMINI-540W Bedienungsanleitung

Securitytronix

Securitytronix ST-IP4FWD Bedienungsanleitung

Securitytronix

Securitytronix ST-D420IR6-B Bedienungsanleitung

Securitytronix

Securitytronix ST-HD-D2812M-2MP Bedienungsanleitung

Securitytronix

Securitytronix ST-D600IR2812-HB Bedienungsanleitung

Securitytronix

Securitytronix ST-HD-BT3.6-1MP Bedienungsanleitung

Securitytronix

Securitytronix ST-IP4VFD-MZL Bedienungsanleitung

Securitytronix

Securitytronix ST-BT540IR30 Bedienungsanleitung

Securitytronix

Securitytronix ST-IP-MD36-1 Bedienungsanleitung

Securitytronix

Securitytronix HD-Coaxinator ST-HD-D2812-1MP Bedienungsanleitung

Securitytronix

Securitytronix ST-D4203.6B Bedienungsanleitung

Securitytronix

Securitytronix ST-DWD600IRVP49-S Bedienungsanleitung

Securitytronix

Securitytronix HD-COAXINATORTVI ST-HDC2FTD Bedienungsanleitung

Securitytronix

Securitytronix ST-IP2PTZ Bedienerhandbuch

Securitytronix

Securitytronix ST-IP-BT3.6-1 Bedienungsanleitung

Securitytronix

Securitytronix HD-COAXINATORTVI ST-HDC2PTZ Bedienungsanleitung

Securitytronix

Securitytronix ST-WD600PTZMINI Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung