Seneca MyBoat Bedienungsanleitung

SENECA s.r.l.

Via Austria, 26 – 35127 – PADOVA – ITALY

Tel. +39.049.8705355 - 8705359 - Fax +39.049.8706287

For manuals and conﬁguration software, visit www.seneca.com/myboat

MI004981-E INSTRUCTIONS IN ORIGINAL LANGUAGE ENGLISH - 1/7

INSTALLATION MANUAL

MyBoat

Real time remote control and alarm

management device for boats

This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.

The content of this document corresponds with the products and technologies described. Data herein may

be modiﬁed or supplemented for technical and/or sales purposes.

MODULE LAYOUT

Weight 150 g Case Polycarbonate / ABS material.

LED SIGNALS ON THE FRONT PANEL

LED STATUS LED MEANING

GSM

(Yellow)

Oﬀ MyBoat oﬀ

Medium ﬂash (64 ms ON / 800 ms OFF)

 Network search

 No signal

 SIM card with incorrect pin

Slow ﬂash (64 ms ON / 3000 ms OFF)

 Registration to the GSM network

successful

Fast ﬂash (64ms ON / 300 ms OFF)

 Successful access to the Internet

network

 Correct APN

 Registration to the GPRS network

successful

PWR

(Green)

Oﬀ

MyBoat on

MyBoat oﬀ

PRODUCT DESCRIPTION

MI004981-E ENGLISH - 2/7

80 mm

108 mm

32 mm

8 mm

MyBoat is a ﬂexible control system consisting of a smart control unit and wireless monitoring sensors for

the remote control and alarm management in real time of yachts, boats and general and ﬂeet. As well as

managing the communication with the sensors and the SENECA cloud platform, the control unit is set for

the advanced conﬁguration and optional remote control of 4 digital inputs, 1 timed relay output (e.g.

siren), 1 non-timed relay output (auxiliary), 1 analogue input for service battery sensor (already wired to

the control unit power supply) and 1 fuel level analogue input. For information on the functions of your kit,

refer to the summary table on the package.

PRELIMINARY WARNINGS

ASSEMBLY STANDARDS

SYMBOLS ON THE ENCLOSURE

PWR power button

Slot for mini SIM

GSM antenna Micro SD card slot

Scroll display button (SCR)

Micro USB connector

TECHNICAL SPECIFICATIONS

POWER SUPPLY

Voltage

absorption

Internal battery (buffer)

6 – 15 V , 500 mA Max.

3.5 W Max.

Lithium Ion 3.7 V - 1000 mAh, rechargeable.

ENVIRONMENTAL CONDITIONS

Temperature

Humidity

Storage temperature

Protection rating

Seneca recommends use at 0 to 45 ° C for correct operation.

With the power supply present: -20 .. + 55 °C.

With use of the battery (when discharged): -20 .. + 45 ° C.

Charging is possible in the range: 0 .. +45°C.

30% – 90%, non condensing.

from -20 °C to +20 °C <1 year; from -20 °C to +45 °C <3 months;

from -20 °C to +60 °C < 1

month IP20

MI004981-E ENGLISH- 3/7

SIM

Electrical and electronic waste disposal (applicable in the European Union and other countries

with recycling programs). The symbol on the product or its packaging shows that the product

must be disposed of at a collection centre authorised to recycle electrical and electronic waste.

The full content of this manual must be read before operation. The device is to be

exclusively used by qualiﬁed electricians.

Damaged parts must be replaced by the manufacturer, who is also responsible for repairing the

device. The product is sensitive to electrostatic discharges. Take appropriate measures during

operation.

The warranty shall become null and void in the event of improper use or tampering with the

device or accessories supplied by the manufacturer as necessary for its correct operation, and if

the instructions contained in this manual are not followed.

For optimum reception of the GPS signal from satellites, it is best to place the MyBoat horizontally in an area

not covered by metal structures. If this is not possible, an optional external antenna with 3m cable (code

AGPS) is available. Follow the procedure supplied with the package for the installation of the external

antenna.

BASIC CARD SPECIFICATIONS

DIGITAL INPUTS

Type

Maximum frequency

Threshold OFF

Threshold ON

4 inputs

Reed, contact, PNP, Pulscap

30 Hz

ANALOGUE INPUTS

Accuracy

type

2 inputs

Voltage 0 - 30 V  / Current 0 - 20 mA

0.1% of the full scale

VOLTAGE OUTPUT: +12 V  50 mA (maximum current)

TEMPERATURE SENSOR NTC thermistor

USB PORT 1 reserved micro USB port

DISPLAY

CONNECTIONS

CPU ARM 100 Mhz 32 bit

INTERNAL MEMORY FLASH 2 MByte (log)

Micro SD slot Type/ Memory Push-Push for SD card and SD HC card / max 32GB

SIM slot Type Push-Push for mini SIM (15 x 25 mm)

MMCX CONNECTOR External GPS antenna connector (optional)

GSM Quad band (850 / 900 / 1800 / 1900 MHz)

GPS CARD SPECtIFICATIONS

RECEIVER 22 channels

SENSITIVITY -165 dBm

FIX TIME 32 s usually

ACCURACY up to 2.5 m

RECEIVER AND SENSOR SPECIFICATIONS

TECHNOLOGY LoRa ®

FREQUENCY BANDS 863 ÷ 870 MHz

SENSITIVITY up to -146 dBm

RF POWER + 14 dBm

RELAY EXPANSION CARD SPECIFICATIONS (OPTIONAL)

REFERENCE STANDARDS

 MI004981-E ENGLISH- 4/7

STANDARD ETSI EN 301 489-7

EN301 511

EN301 489-1

IEC / EN 60950

DIGITAL

OUTPUTS

2 outputs

Relay 3 A max - 250V SPST (with shared terminal)

0 - 3 V, I < 1 mA

6 - 24 V, I > 3 mA

128 x 32 LCD Dots with visible area of 39 mm x 8.6 mm

Spring clamps, 3.5 mm pitch, connector for Micro USB and SMA

connector for GSM Antenna

•

ON/OFF BUTTON AND SCROLL DISPLAY BUTTON

•

MICRO USB PORT AND POWER SUPPLY

•

AUTO SHUTOFF

INSERTING THE SIM CARD AND SD CARD

•

INSERTING THE SIM CARD

•

INSERTING THE MICRO SD CARD

MI004981-E ENGLISH - 5/7

INITIAL POWERING ON OF THE DEVICE

ANTENNA

micro

USB

PWR SCR

ANTENNA

SIM

card

MyBoat is supplied in "shipping mode".

This mode avoids any unnecessary discharge of the battery during storage and shipping.

When switched on for the ﬁrst time, power the device with the power cord supplied;

this allows "shipping mode" to be exited.

MyBoat is equipped with a PWR button located on the top left side (front

panel view). Pressing this button turns the module on and off. To switch it

off, hold the PWR key down for a few seconds.

MyBoat is also equipped with a SCR button, located on the top right side

(front panel view). Pressing this key displays the parameters.

The device has a micro USB connector on the left side of its enclosure,

which can be used for conﬁguration, ﬁrmware updates and to recharge the

internal battery.

To recharge the internal battery, use:

- the power cord with cigarette lighter socket, equipped with a fuse

connecting the cables to the + and- (GND) terminals.

- a PC via the micro USB port with a standard cable.

Power supply through the USB jack is not suitable for ﬁxed installations, or

conﬁgurations where relays and/or digital inputs are used.

If the display indicates "LOW BAT", it means that the internal battery is almost

empty: after 60 seconds from this indication, the device switches off automatically.

To restore the battery charge to an appropriate value, power the

device using one of the recommended modes.

MyBoat has an entry for mini SIM located in the right side of the enclosure.

To insert the card in its corresponding slot, make sure the metal contacts are facing

right (as seen in the ﬁgure).

MyBoat is equipped with an SD card input that can be used to update the

device's ﬁrmware and update the information and connection parameters with

the world's best known telephony operators.

Note: DO NOT REMOVE THE CONTENT OF THE SD CARD PROVIDED. THIS

MAY RESULT IN FAILED DATA CONNECTION WITH THE MYBOAT

SERVICE.

The input for micro SD card is located on the right side of the enclosure.

To insert the SD card in its corresponding slot, make sure the metal contacts are

facing right (as seen in the ﬁgure).

SAFETY INFORMATION

ELECTRICAL CONNECTION

MI004981-E ENGLISH - 6/7

•

INSERTION AND EXTRACTION FROM TERMINALS WITH A PUSH-WIRE

Insertion o

a rigid cable

Press down Recommended

ﬂaying: 8-9 mm

Insertion o

a ﬂexible

cable

A Press with

screwdriver

B Insert the

cable

Extraction

of a cable

A Press with

a screwdriver

B Extract

the cable

•

PUSH-WIRE TERMINAL BLOCK

(timed) AUX1

Shared of the two relays

(not timed) AUX2

(normally closed) DIN4

AUX + 12 Vdc

(service battery sensor) AIN 1

0 V= 0%; 10 V = 100% NTC

GND

(Sensor input) NTC

+ Power

- Power

1 2

45 6 78 9 10 11 12 -

MyBoat has a terminal block inside its enclosure.

To access the internal terminal block of the device, unscrew the screw at the

centre of the black cover positioned at the bottom of the enclosure and lift up.

In the side ﬁgure, the cover has been removed.

IMPORTANT: With the relay card, mobile wiring of cables connected to

terminals is not permitted. To make the cables from the terminals safe, use the

break-out passages in the back of the enclosure. When the wiring is complete,

fasten the protective cover on the device with the screw to prevent any

accidental contact.

(normally closed) DIN3

(normally closed) DIN2

(normally closed) DIN1

ACCESSORIES

OPTIONAL ACCESSORIES

External GPS antenna with 3 m cableA-GPS

A-GSM/QUAD-N

CPS-TIP-MP

MYBOAT-S1

MYBOAT-S2

MYBOAT-S3

MYBOAT-S4

MYBOAT-S5

MYBOAT-S6

MYBOAT-S7

MYBOAT-S8

External GSM / QUAND-N antenna with 5 m cable

SPARE ACCESSORIES

Spare cigarette lighter power supply

Replacement sensor for access control

Replacement sensor for bilge monitoring

Replacement sensor for access control

Replacement sensor for battery monitoring

Replacement sensor for bilge monitoring

Replacement sensor for access control

CONTACTS

Technical support [email protected]

Product information sales@seneca.it

MI004981-E ENGLISH - 7/7

Andere Handbücher für MyBoat

Inhaltsverzeichnis

Andere Seneca Adapter Handbücher

Seneca

Seneca Z-107E Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung