Servomex 1900 Bedienungsanleitung

1900

Oxygen Analyser

Hazardous Area

™

Please record your analyser details below

Part Number

Serial Number

Tag Number

1900 Series

235

227

159

60 6860

25844

387

448

118 44

174

407

168

1900 Series

iii

RELAY CONTACTS SHOWN

IN DE-ENERGISED POSITION

0-1V NON

ISOLATED

4-20mA

ISOLATED

F1.

F3.15A.

HBC.

OUTPUT

TB-3

(1)

N (2)

L (3)

RANGE

FLOW

ALARM

ALARM 2

ALARM 1

ALARMS

SUPPLY

ZERO

SPAN

TB-2 TB-4

TB-3

1900 Series

Alarm Set

Span

Zero

Low

Alarm

20.9 %O2

AlarmFlowPower

Range 1

Range 2

Range Set

100%

50%

25%

10%

100%

50%

25%

10%

LK4

RANGE 2

LK3

RANGE 1

NOT FITTED

FITTED

FLAL

LK5

LK1 LOW

HIGH

ALARM 1

LK2

ALARM 2

LOW

HIGH

LK6

FAI LURE MODE

LOW

HIGH

1900 Series

Notes

xendos 1900 Series 1

1 INTRODUCTION

1.1 Warnings, Cautions and Notes

This manual includes WARNINGS, CAUTIONS and NOTES which provide information

relating to the following:

WARNINGS

Hazards which could result in personal injury or death.

CAUTIONS

Hazards which could result in equipment or property damage.

NOTES

Alert the user to pertinent facts and conditions.

1.2 Scope of this manual

This manual covers installation, normal operation and routine maintenance of the

Servomex paramagnetic oxygen analyser, xendos 1900 Series

• For latest technical specification refer to the Technical Data Sheet.

• Addresses for technical assistance and spares are given on the rear cover.

• A service manual is available for use by qualified personnel, part number

01800002B.

About this manual

Ref:01900/003B/3

Order as part 01900003B

xendos 1900 Series

KEY TO FIGURES

Figure A Mounting details

1. M6 bolt (4 off) 5mm allen key 7. Purge outlet (if used)

2. LH cover (hinged) 8. Sample outlet

3. Display window 9. Sample inlet

4. RH cover 10. Cable entries (3 off)

5. M8 mounting slot (4 off) 11. M6 earth stud

6. Purge inlet (if used) 12. Breather

(Sample , Purge Inlet / Outlet and Breather Port - ¼”NPT.INT)

Figure B Electrical connections

1. Range contacts 7. Electrical supply terminals

2. Flow Fail alarm contacts 8. Output cable entry

3. Alarm 2 contacts 9. Supply cable entry

4. Alarm 1 contacts 10. Alarm cable entry

5. Linear non isolated Output signals (Cable entries - ¾”NPT, M20 or Pg13.5)

6. Linear isolated Output signals 11. Power Supply Fuse (F1) - F3.15A HBC

Figure C Control panel (hinged)

1. Power On LED 7. Flow Failure LED

2. Set ZERO potentiometer 8. Alarm LED

3. Set SPAN potentiometer 9. Range change push button

4. Set ALARM push button 10. Range label (Slip In)

5. Alarm LEDs 11. Sample filter (Screws in through control panel)

6. Digital display (0.0 to 100.0% O2) 12. Range LEDs

optional (0.00 to 100.00% O2)

Figure D Link settings on housekeeping board

1. Flow alarm (LK5) 4. Failure Mode (LK6)

2. Range 1 (LK3) 5. Alarm 2 (LK2)

3. Range 2 (LK4) 6. Alarm 1 (LK1)

EC Directive Compliance

The xendos 1900 complies with the EMC Directive 89/336/EEC (as

amended by Directives 92/31/EEC and 93/68/EEC) and the ATEX

Directive 94/9/EC.

xendos 1900 Series 3

1.3 Unpacking

WARNING

The xendos 1900 weighs approximately 26kg (57lbs) and care must

be taken when handling. It is recommended that it is lifted with the

fingers positioned underneath the rear casting.

• Remove the xendos 1900 from its packing and inspect it for damage.

• If damage has occurred, inform Servomex or its agent immediately.

• Retain all packing and shipping information for future use.

2. INSTALLATION

WARNING

•Refer to Conditions for Safe Use before installation.

•The Terminal chamber on the right hand side of the analyser

should not be opened while energised or within 3 minutes

following removal of power.

•Refer servicing to qualified personnel with knowledge of

hazardous area requirements.

Andere Handbücher für 1900

Inhaltsverzeichnis

Andere Servomex Messgerät Handbücher

Servomex

Servomex 2700 Bedienungsanleitung

Servomex

Servomex SERVOTOUGH SpectraExact 2500 Series Bedienungsanleitung

Servomex

Servomex SERVOFLEX MiniMP Bedienungsanleitung

Servomex

Servomex SERVOPRO FID Bedienungsanleitung

Servomex

Servomex SERVOTOUGH Laser 3 Plus Bedienungsanleitung

Servomex

Servomex 2700 Bedienungsanleitung

Servomex

Servomex SERVOTOUGH LaserExact 2950 Bedienungsanleitung

Servomex

Servomex SERVO PRO 14440D1 Bedienungsanleitung

Servomex

Servomex 1900 Bedienungsanleitung

Servomex

Servomex SERVOTOUGH Oxy Bedienungsanleitung

Servomex

Servomex Servotough SpectraScan 2400 Bedienungsanleitung

Servomex

Servomex SERVOTOUGH LaserSPII mini Bedienungsanleitung

Servomex

Servomex SERVOPRO MultiExact Bedienungsanleitung

Servomex

Servomex SERVOPRO 4000 Series Bedienungsanleitung

Servomex

Servomex 1100A Bedienungsanleitung

Servomex

Servomex SERVOFLEX MiniFood Pack Bedienungsanleitung

Servomex

Servomex SERVOPRO Chroma Bedienungsanleitung

Servomex

Servomex 1900 Bedienungsanleitung

Servomex

Servomex NanoTrace DF-745SG Bedienungsanleitung

Servomex

Servomex SERVOPRO Plasma Bedienungsanleitung

Servomex

Servomex 2500 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung