SEWOO WTP-150 Bedienungsanleitung
WTP-150
Thermal Receipt printer
Technical manual
SEWOO TECH CO., LTD.
www.miniprinter.com
TABLE OF CONTENTS
1. General Specifications
1.1 Printing Specifications
1.2 Character Specifications
1.3 Auto Cutter
1.4 Paper Roll Supply Device
1.5 Paper Specification
1.6 Printable Area
1.7 Printing and Cutting Positions
1.8 Internal Buffer
1.9 Electrical Characteristics
1.10 EMI and Safety Standards Applied
1.11 Reliability
1.12 Environmental Conditions
2. Configuration
2.1 Interface
2.1.1 RS-232 serial interface
2.1.2 Specifications
2.1.3 Switching between on-line and off-line
2.1.4 Interface connector terminal assignments and signal functions
2.1.5 Serial interface connection example
2.1.6 Centronics parallel interface
2.1.7 Data Receiving Timing(Compatibility Mode)
2.1.8 USB Interface
2.1.9 Interface Connector
3. Connectors
3.1 Interface Connectors
3.2 Electrical Characteristics
3.3 Drawer kick-out Connector (Modular Connector)
4. Control Command Summary
TITLE : WTP-150
Page -1 -
1. General Specifications
1.1 Printing Specifications
1) Printing method: Thermal line printing
2) Dot density: 180dpi x 180dpi
203dpi x 180dpi
3) Printing direction: Unidirectional with friction feed
4) Printing width: 72mm(2.83"), 576 dot positions (203dpi)
72.2mm(2.84"), 512 dot positions (180dpi)
80mm(3.15"), 640 dot positions (203dpi)
5) Characters per line(default): Font A: 42
Font B: 56
6) Printing speed: High speed mode:
35.5lines/second maximum
(1/6inch feed) (at 24V, 20℃)
Approximately 150mm/sec maximum
(approximately 5.9inchs/sec maximum)
☞ NOTE: Speeds are switched depending on the applied voltage to the printer and
head temperature conditions automatically.
☞ NOTE: There may be variations in printing after switching the mode of the
printing speed. To prevent this for logo printing with ESC* command,
using a downloaded bit image is recommended. Change in printing
speed does not occur during down loaded bit image printing.
7) Line spacing (default): 1/6 inch (4.23mm)
Programmable by control command.
TITLE : WTP-150
Page -2 -
1.2 Character Specifications
1) Number of characters: Alphanumeric characters: 95
Extended graphics 128 × 7 pages
(including one space page)
International characters: 32
① English
② Hangul
③ Chinese (GB2312,Big5)
④ Kanji
2) Character structure: Font A: 12 ⅹ 24
Font B: 9 ⅹ 24
Hangul, Chinese: 24 ⅹ 24
Font A is selected as the default
3) Character size:
EPSON Emulation STAR Emulation
Dot density 0.141ⅹ0.141mm/dot
(180*180dpi)
0.125ⅹ0.141mm/dots
(203*180dpi)
[dpi: dots per 25.4mm{1"}]
3)Printing direction Unidirectional With friction feed
4)Paper width
82.5mm
(3.25")
80mm
(3.15")
60mm
(2.36")
58mm
(2.28")
82.5mm
(3.25")
80mm
(3.15")
60mm
(2.36")
58mm
(2.28")
5)Maximum
printable area
72.2mm
(512dots)
72.2mm
(512dots)
54.1mm
(384dots)
50.8mm
(360
dots)
80mm
(640dots)
72mm
(576
dots)
54.5mm
(436
dots)
52.5mm
(420
dots)
6)Character / line
Font A (12ⅹ24) 42 42 32 30 53 48 36 35
Font B (9ⅹ24) 56 56 42 40 71 64 48 46
Kanji Font (24ⅹ24) 21 21 16 15 26 24 18 17
1.3 Auto Cutter
Partial cut: Cutting with one point center uncut
NOTE: To prevent dot displacement, after cutting, paper must be fed
approximately 1mm(14/360 inches) or more before printing.
TITLE : WTP-150
Page -3 -
1.4 Paper Roll Supply Device
1) Supply method: Drop-in paper roll
2) Near-end sensor:
a) Detection method: Photo Reflector
b) Paper roll spool diameter: Inside: 12mm(.47″ )
Outside: 18mm(.71″)
c) Near-end adjustment: Adjusting screw
d) Remaining amount: Fixed position #1 (approximately
23mm(0.9″ )) #2 (approximately
27mm(1.06″ ))
NOTE: You can use a command to stop printing upon detection of a paper
near-end.
1.5 Paper Specification
1) Paper type: Specified thermal paper
2) Form: Paper roll
3) Paper width:
(82.5mm paper width model)
82 ±0.5mm (3.23" ±0.02")
(80mm paper width model)
79.5 ±0.5mm (3.13" ±0.02")
(60mm paper width model)
59.5 ±0.5mm (2.34" ±0.02")
(58mm paper width model)
57.5 ±0.5mm (2.26" ±0.02")
4) Paper roll size: Roll diameter : Maximum 83mm
Take-up paper roll width:
80 ± 0.5, 1.0mm(3.15"±0.020", 0.04")
5) Paper roll spool diameter: Inside: 12mm(.47")
Outside: 18mm(.71")
NOTE: Paper must not be pasted to the paper roll spool.
TITLE : WTP-150
Page -4 -
1.6 Printable Area
<EPSON Emulation>
6.8mm
0.141mm
<82.5mm {3.25"} paper width model>
82±0.5mm
3mm
512 dots
72.2mm(dot #1-#512)
4.3mm
<80 mm {3.15"} paper width model>
0.141mm
79.5±0.5mm
3mm
512 dots
72.2mm(dot #1-#512)
TITLE : WTP-150
Page -5 -
59.5±0.5mm
<60mm {2.36"} paper width model>
0.141mm
3mm 2.4mm
384 dots
54.1mm(dot #1-#384)
57.5±0.5mm
0.141mm
3mm 3.7mm
360 dots
<58mm {2.28"} paper width model>
50.8mm(dot #1-#360)
Figure 1.6.1 Printable Area for EPSON Emulation
TITLE : WTP-150
Page -6 -
<STAR Emulation default setting>
57.5±0.5mm
<58mm {2.28"} paper width model>
0.125mm
2.65mm
420 dots
2.35mm
52.5mm(dot #1-#420)
Figure 1.6.2 Printable Area for STAR Emulation (for Default Setting)
<STAR Emulation when the paper width is changed>
82±0.5mm
<82.5 mm {3.25"} paper width model>
0.141mm
1mm 1mm
640 dots
80mm(dot #1-#640)
TITLE : WTP-150
Page -7 -
4.85mm
0.141mm
79.5±0.5mm
<80mm {3.15"} paper width model>
2.65mm
576 dots
72mm(dot #1-#576)
59.5±0.5mm
<60mm {2.36"} paper width model>
0.125mm
2.65mm 2.35mm
420 dots
54.5mm(dot #1-#436)
Figure 1.6.3 Printable Area for STAR Emulation (When the Paper Width Is Changed)
NOTE : The numeric values used here are center values to be used in designing. The
printable area may be out of alignment by 2 mm maximum to the left or right, due to the
paper position or tolerance of parts.
TITLE : WTP-150
Page -8 -
1.7 Printing and Cutting Positions
e
nter of the
p
rint dotline
t
o-cutter blade
p
osition
Manual-cutter position
[Units: mm(Al the numeric values are typical.)]
Appro *12.6
Paper feed direction
Appro * 30.5
Figure 1.7.1 Printing and Cutting Positions
NOTE: Numeric values used here are center values to be used in designing. The values may
vary slightly as a result of paper slack or variations in the paper. Take this into account
when setting the cutting position of the autocutter.
TITLE : WTP-150
Page -9 -
Andere Handbücher für WTP-150
1
Inhaltsverzeichnis
Andere SEWOO Drucker Handbücher
SEWOO
SEWOO LK-P43II Bedienungsanleitung
SEWOO
SEWOO LK-P20II Bedienungsanleitung
SEWOO
SEWOO SLK-TL21 Series Bedienungsanleitung
SEWOO
SEWOO LK-TL200 Bedienungsanleitung
SEWOO
SEWOO LK-D10 Bedienungsanleitung
SEWOO
SEWOO LK-P400 Bedienungsanleitung
SEWOO
SEWOO SLK-T12EB Bedienungsanleitung
SEWOO
SEWOO SLK-TE32 Series Bedienungsanleitung
SEWOO
SEWOO LK-P21 Bedienungsanleitung
SEWOO
SEWOO LK-P20II Bedienungsanleitung
SEWOO
SEWOO LK-P11B Bedienungsanleitung
SEWOO
SEWOO LK-P30 Bedienungsanleitung
SEWOO
SEWOO SLK-T20EB Series Bedienungsanleitung
SEWOO
SEWOO LK-P41 Montageanleitung
SEWOO
SEWOO SLK-TE25 Bedienungsanleitung
SEWOO
SEWOO LK-B10 Bedienungsanleitung
SEWOO
SEWOO SLK-TS400EB Bedienungsanleitung
SEWOO
SEWOO SLK-T42 Bedienungsanleitung
SEWOO
SEWOO LK-P34 Bedienungsanleitung
SEWOO
SEWOO LK-P30B Bedienungsanleitung
