SHAREBOT 42 Bedienungsanleitung

Sharebot-42

Quick Start Guide

Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Sharebot 42

(S42N1R) o cerca il tuo prodotto tra le migliori offerte di Stampanti

Index
Your new Sharebot 42..........................................................................................................................3
Safety guidelines..................................................................................................................................4
Extruder...........................................................................................................................................4
Heated printing plate........................................................................................................................4
Personal protective e uipment.........................................................................................................4
Moving parts....................................................................................................................................4
Package contents..................................................................................................................................5
Welcome Kit....................................................................................................................................5
Sharebot toolbox..............................................................................................................................5
Test material.....................................................................................................................................5
Working with your Sharebot 42............................................................................................................6
Extruder unpack...............................................................................................................................6
Insert filament into the extruder.......................................................................................................6
The first object.................................................................................................................................6
Machine...........................................................................................................................................7
The display...........................................................................................................................................8
Home................................................................................................................................................8
Print..................................................................................................................................................8
Settings.............................................................................................................................................9
Prepare........................................................................................................................................9
Tune...........................................................................................................................................10
File operations...........................................................................................................................10
Configurations submenu...........................................................................................................11
Changing the “Probe Offset”.....................................................................................................11
Software operations.......................................................................................................................11
Network configuration........................................................................................................................13
Web interface – Sharebox 3D........................................................................................................13
Dashboard.................................................................................................................................14
File manager..............................................................................................................................14
Warranty.............................................................................................................................................16
Moving parts..................................................................................................................................16
Packaging.......................................................................................................................................16
Resources............................................................................................................................................17
Online.............................................................................................................................................17
Technical assistance.......................................................................................................................17

Your new Sharebot 42

Sharebot 42 introduces a lot of new features compared to the product base on FFF technology

previously made by Sharebot srl:

•Printing area 250X220X200 mm

•New magnetic printing support, with metal plate

•New extruder with interchangeable nozzle

•New web-based software interface for controlling and starting the printing process remotely

•Touch-screen display

•Real-time monitoring of the print job via web cam

•Loading files from USB, internal memory and web interface

•Additional USB socket for future expansion, inside the 3d printer

•Automatic Z levelling with with proximity probe sensor

•Real-time calibration of the printing plate on the Z

•Automatic Calibration on Y1 and Y2 axes every time the printing process is starting, for a

perfect square

•Filament detection sensor

•Magnetic support for customizable spools 300/750 gr

•Accommodation inside the machine body of the spool

•Housing equipment in the machine base

Safety guidelines

Extruder

In FFF technology 3D printers, the thermoplastic filament is melted in the nozzle (the terminal part of

the extruder) at a temperature varying between 190 and 280°C.

During the printing process you mustn't touch the nozzle with hands.

The contact even for a very short time causes burns.

In case of routine maintenance or for replacing the nozzle, you have always to use protection items

required for hands and eyes protection.

The extruder temperature is always visible on the main display screen.

Heated printing plate

Under the magnetic plate, it is placed the heated plate which is used to improve adhesion of the model

during the printing process. The heat generated by the heated plate is also transmitted to the magnetic

printing support.

The heated surface reaches a maximum temperature of 90°C and remains high even after the end of

the printing job, also when the machine is turned off.

The contact with the plate at high temperatures causes burns.

Personal protective equip ent

You have always to use the machine in safe condition, adopting the appropriate Personal Protective

Equipment of Category 1, in accordance with Legislative Italian Decree no. 475/92 on safety in the

workplace.

In particular, always use gloves and goggles during maintenance of hot parts.

Moving parts

During the printing process don't touch with hands the moving parts in the inner part of the machine or

any other items.

In case of failure of the printing, stop the printing process and proceed in the maintenance of the printer.

Package contents

Fist of all, check that there are no damages to the machine and that all items listed below are included

in the package or in the Sharebot toolbox.

Your package should contain:

–a box with the welcome kit;

–3D printer Sharebot 42 with the 0.4 mm nozzle.

Welco e Kit

The Welcome Kit contains:

–a Sharebot toolbox;

–PLA filament;

–magnetic printing support for the printing plate;

–magnetic support for the spoon 300 / 750gr;

–adapter for the magnetic support;

–a folder containing the quick start guide and warranty;

–power cable.

Sharebot toolbox

The Sharebot toolbox contains:

–Nippers

–Cutter

–Allen screwdriver size 2.5

–Allen "L" key

–Gear grease

–Hair spray

–"Unlocks nozzle" tools

Test aterial

In the Kit there is a test spoon of PLA.

The test material is guaranteed by Sharebot srl.

Spoon from other suppliers can be used under the fully responsibility of the end user.

Any damage to the machine coming from the use of a filament not certified by Sharebot will lead to a

lack of warranty.

Working with your Sharebot 42

Before starting to use your printer it is necessary to:

–place the machine in a wide and appropriate area;

–connect the power cable C13 - IEC 60320 into the socket on the side of the machine;

–power on the machine with the ON / OFF switch;

–verify that the display works;

–position the spoon of filament on the magnetic support, adding any size adapter;

–place the filament spoon into the compartment, pay attention to the filament direction;

Extruder unpack

Before starting the printer process you must unpack the extruder by following these steps:

1) cut the straps that keep together the hard black polyethylene panel;

2) move the carriage of the extruder at the back along Y axis;

3) remove the polyethylene panel carefully;

4) cut the cable tie to release the extruder carriage on axis X.

Insert fila ent into the extruder

Now you can insert the filament into the extruder:

–cut the head of the filament from the spoon with an angle of 45° or more;

–insert the filament in the movement sensor and push it until filament arrives to the extruder;

–from the printer menu select “Settings” - “Prepare” - “Change filament”, wait for the heating of

the extruder then click the “Confirm” button on the screen;

–if necessary remove the Teflon tube and insert in the second pusher device the filament by

hand;

–wait until the nozzle works, pushing out the material and click on the confirmation button to

finish the operation;

And remember to keep the supplied tools near the machine.

The first object

In the internal memory of the machine is preloaded a file .GCODE to build your first object.

Tostart the process follow this procedure:

–press the “Print” icon;

–select “File from memory”;

–select the file.

We recommend observing the printed object, in particular paying attention to the main characteristics:

–the first layer;

–the initial layer (bottom) and final (top);

–filling (infill).

With the use of slicing software you can change the parameters that determine these characteristics

and the final print quality.

Machine

The machine is delivered calibrated and ready to use (Plug and Play).

The plate is the surface on which the object production will take place . Sharebot 42 print area is about:

X axis 250 mm

Y axis 220 mm

Z axis 200 mm

The display

Sharebot 42 display is touch and color.

The display is the main interface to manage printing process, select files and set the parameters to

optimize the process.

Ho e

The “Home” or “Main screen” is the default screen displayed by the machine when it's turned on.

The main information available are:

–A: status bar with the object name, elapsed time and last message;

–B: percentage of the running process;

–C: actual extruder temperature (green) and target temperature (black);

–D: actual printing bed temperature (green) and the target temperature (black);

–E: command execution speed, 100% means use the gcode values.

In the F area you have the commands to pause and stop the running process.

Touch the C,D or E areas to change the corresponding parameter. The values can be adjusted by

setting the variation range (0.1; 1; 10; 100) and setting the desired value using the + and – controls.

OFF resets the full scale value.

Totemporarily stop the printing process, select “Pause”. The machine will not stop immediately but it

will execute all the commands already stored in the internal memory and after the latter have been

executed it will stop.

Use the “Resume” command to let the printing process restart.

Do not press the “Resume” button until the machine has stopped.

You can return to the “Main screen” pressing the Sharebot icon usually available in the upper left corner

of the screen.

Using the “Print” icon:

you will be able to select the gcode file containing model to be build.

The gcode contains instructions for moving the machine axes, the extruder and other print parameters.

A gcode file is generated using a slicer to convert a 3D object in STL or OBJ format; the use of an

unsupported slicer or an unofficial profile can damage your printer.

After pressing the button you can select the device that contains your file:

Selecting theA or B area because you can print an object taken from the internal memory of the

machine (A) or from the connected USB key (B).

The machine display shows only files with gcode (* .gcode, .gco *) extensions.

Toload a print file in Sharebot 42, you can use the USB port, located in the front of the machine. In this

case the machine copies the file into his internal memory before starting the printing process, so that

you can remove the USB stick without interrupting it.

Settings

This menu contains the commands to set and modify the operating parameters. It contains the

“Prepare” and “Tune” options that are mutually exclusive and will be shown based on the printer status.

The “Prepare” submenu is available only before the starting of the print to set the working parameters.

The “Tune” submenu is available only during the printing process to change the process parameters in

real time and optimize the prints.

Prepare

COMMAND FUNCTION

Disable Stepper Deactivation of all stepper motors

Auto Home Extruder move to the home position

preheat Heat the extruder

Cool down Cooling of all heated components (extruder and

heated plate)

Move axis Axis movement

Move filament Moves filament through pusher

Change filament Start the filament change cycle

Calibrate bed man Activating the manual calibration process, for a

mechanical flatness of the printing plate

Enable Filament Detection Enabling the sensor of the filament motion

Disable Filament Detection Disabling the filament motion sensor

Tune

COMMAND FUNCTION

Speed Speed variation of all print parameters

(percentage)

Bed Variation of the temperature of the heated floor

Change filament Change the filament process

Fan Speed Speed variation of the extruder fan

Enable Filament Detection Enabling the filament motion sensor

Disable Filament Detection Disabling the filament motion sensor

File operations

COMMAND FUNCTION

Copy files Copying a file from USB memory to the internal

memory (also inverse operation)

Delete files

Delete files Deleting a file from the USB memory or internal

memory

Configurations sub enu

Inhaltsverzeichnis

Andere SHAREBOT 3D-Drucker Handbücher

SHAREBOT

SHAREBOT Kiwi-3D Bedienungsanleitung

SHAREBOT

SHAREBOT Kiwi-3D Bedienungsanleitung

SHAREBOT

SHAREBOT Next Generation XXL+ Bedienungsanleitung

SHAREBOT

SHAREBOT BIG Bedienungsanleitung

SHAREBOT

SHAREBOT Next Generation Bedienungsanleitung

SHAREBOT

SHAREBOT VIKING Bedienungsanleitung

SHAREBOT

SHAREBOT Q Dual Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch