SHAREBOT Next Generation XXL+ Bedienungsanleitung
Sharebot Next Generation XXL+
user's manual
Version 0.4 - 06/201
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page 1
Sharebot Next Generation XXL+
user's manual
ATTENTION – EXTRUDER
The fusion and extrusion system of the thermoplastic filament requires a heated end up to temperatures of 250 degrees and more. The contact, even for a very limited
time, with the heated part causes burns. You must avoid to put your hands or other body parts in the printing area when printing and for minutes after the printing process
is over. The current temperature of the extruder is indicated on the LCD screen.
ATTENTION – HEATED PRINTING BED
All the printing plate is made of metal with the addition of a glass plate. This device is electrically heated and serves to bring to desired temperature the entire printing
bed, including the glass plate. The temperature is measured directly on the heating plate: so the temperature of the glass plate will be less than the one shown for several
minutes after the beginning of the heating process, but likewise it may be warmer than what is indicated on the display for several minutes after the end of the printing
due to the the phenomenon of thermal inertia. Remember that it can be set in special cases for temperatures of 90 degrees, while the recommended temperature for
prints is usually 80 degrees. At these temperatures the unintentional contact does not produce damage and burns if you retract immediately the body part that is in
contact, while at higher temperatures it greatly reduces the time necessary to create burns. You have always to check the temperature indicated on the display before you
start maneuvering like the removing of the glass plate on the printing bed.
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page 2
Sharebot Next Generation XXL+
user's manual
Indice generale
ATTENTION – EXTRUDER..................................................................................................................................................................................2
ATTENTION – HEATED PRINTING BED........................................................................................................................................................2
Support Policies ...................................................................................................................................................................................................5
Technical characteristics .....................................................................................................................................................................6
1 - Preliminar Operations .................................................................................................................................................................................
Experience Sharebot XXL+..................................................................................................................................................................8
Opening the package ...........................................................................................................................................................................10
Positioning the printer .........................................................................................................................................................................11
Assembling the spool-holder ............................................................................................................................................................12
2 – The workflow of 3D printing....................................................................................................................................................................12
3D model file............................................................................................................................................................................................13
Downloading from internet ...............................................................................................................................................................13
From a 3D model to a printing file .................................................................................................................................................14
A good STL, a good slicing, a good print ......................................................................................................................................14
The printing file: G-code.....................................................................................................................................................................15
Storing the files ......................................................................................................................................................................................15
3 - LCD screen........................................................................................................................................................................................................15
Informative screen..................................................................................................................................................................................16
The Control knob ...................................................................................................................................................................................16
Access to principal menu ....................................................................................................................................................................1
Printer waiting for work..........................................................................................................................................................1
Printer during printing.............................................................................................................................................................1
“Prepare” menu........................................................................................................................................................................................1
“Tune” menu..............................................................................................................................................................................................18
4 - Setting the printer........................................................................................................................................................................................20
Loading the filament ............................................................................................................................................................................20
How to calibrate the printing bed....................................................................................................................................................22
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page 3
Sharebot Next Generation XXL+
user's manual
Plate levelling (calibration)...................................................................................................................................................23
Adjusting pression force on filament..............................................................................................................................................24
5 – Our first 3D printing....................................................................................................................................................................................24
SD card........................................................................................................................................................................................................24
Let's print!..................................................................................................................................................................................................25
Stop the printing process.....................................................................................................................................................................25
Modify the parameters during printing..........................................................................................................................................25
Detach the printed part........................................................................................................................................................................26
6 – Generate our Gcode.....................................................................................................................................................................................28
Slic3r............................................................................................................................................................................................................28
Load the Sharebot profiles in Slic3r..................................................................................................................................28
Import the STL to print...........................................................................................................................................................29
Fundamental parameters of Slic3r.....................................................................................................................................30
The Slicing process...................................................................................................................................................................30
Simplify3D.................................................................................................................................................................................................31
- Printing behaviour of thermoplastic materials ................................................................................................................................32
Printing behaviour of PLA...................................................................................................................................................................33
The heated bed........................................................................................................................................................................................33
8 - Consideration about models orientations............................................................................................................................................33
The orientation........................................................................................................................................................................................34
Cutting the object...................................................................................................................................................................................34
The support material.............................................................................................................................................................................34
Details in prints.......................................................................................................................................................................................36
Clips position............................................................................................................................................................................................3
10 - Ordinary maintenance................................................................................................................................................................................3
Taking care of the printer....................................................................................................................................................................3
Printing plate............................................................................................................................................................................................38
Regulation of pressure upon filament ...........................................................................................................................................38
Nozzle..........................................................................................................................................................................................................38
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page 4
Sharebot Next Generation XXL+
user's manual
Lubrication.................................................................................................................................................................................................38
Belts tension.............................................................................................................................................................................................39
Checking of proper ventilation..........................................................................................................................................................39
Firmware Update.....................................................................................................................................................................................39
Warnings on the safety.......................................................................................................................................................................................39
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page 5
Sharebot Next Generation XXL+
user's manual
Support Policies
If you have any problems in using our printers, the procedure to be followed is as follows:
Check the manual and guides available on the web site;
Contact the dealer from which you purchased the machine;
Contact our technical support by filling out the form beside remember to fill in all fields. Our technicians will reply within 3 working days.
http://www.sharebot.it/index.php/support-en/?lang=en
In case your printer should return in the factory to be repaired, our technical support will assign it a file number to return and we will provide all the additional
information required.
Atte tio : the package should be the origi al o e, pe alty forfeiture of the guara tee.
Check out this video to see how to pack the printer for assistance.
Upon receiving your printer, our technicians will assess whether the problem results from a failure, in this case the repair under warranty will be carried out for free, or by
improper use of the printer or by an improper use of material not approved by Sharebot: in the latter case we will provide you a quotation to request your consent to
repair. For out-of-warranty printers may be required a quote for the inspection. Troubleshooting is a very important task for us and we think is necessary to share
experiences, problems and solutions. Because of that please give priority to the use of the form that will also allow others to take advantage of our and your efforts. Visit
our website for more information.
If you are interested in customized assistance programs please contact [email protected]
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page 6
Sharebot Next Generation XXL+
user's manual
Technical characteristics
Printing technology : Fused Filame t Fabricatio
Printing volume : 705 x 250 x 200 mm +/- 10mm
Theorical positioning resolution axes X and Y : 0,06mm
Risoluzione di posizionamento Z: 0,0025mm
Extruder diameter: 0,4mm
Positioning resolution axis Z : 1,75mm
PLA best extruding temperatures: PLA: 200-230°
Maximum temperature heated printing bed: 90°
Supported and tested printing filaments : PLA
External Dimensions: 955 x 470 x 445 mm
Weight: 40 kg
Power consumption: 500 watt
Electro ic board compatible with Ardui o Mega 2560 with Firmware Ope Source https://github.com/Sharebot3D/Marli
X-Y carriage auto-calibrated
LCD scree 20 x 4 with me ù avigatio (e coder)
Filame t se sor
Extruder block with regulatio pressure upo filame t
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page
Sharebot Next Generation XXL+
user's manual
1 - Prelimi ar Operatio s
Experience Sharebot XXL+
Your professional 3D printer Sharebot Next
Generation XXL+ is a tool of precision, designed,
developed and assembled in Italy by qualified staff.
Before leaving the factory it was submitted to a
quality control and to a quality test that guarantees
its operation. It’s very important, before you can use
the printer, knowing all the technical terms used in
this handbook and identify all the specific
components that form a Sharebot XXL+.
1 Filament teflon sheath
2 Extrusion head cable
3 LCD screen
4 Calibration screws
5 Clips position
6 Frontal ventilation of electronic
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page 8
Sharebot Next Generation XXL+
user's manual
SD card slot
8 LCD control knob
9 Glass printing bed
10 Lateral ventilation of electronic
11 USB connection (only for update)
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page 9
Sharebot Next Generation XXL+
user's manual
1 Presence filament sensor
2 Label with Identification Code (inside the printer, on the right part of the chassis)
3 Switch and power cable socket
Sharebot srl Nibionno Italy
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior permission
page 10
Inhaltsverzeichnis
Andere SHAREBOT 3D-Drucker Handbücher
SHAREBOT
SHAREBOT Q Dual Bedienungsanleitung
SHAREBOT
SHAREBOT Next Generation Bedienungsanleitung
SHAREBOT
SHAREBOT VIKING Bedienungsanleitung
SHAREBOT
SHAREBOT Kiwi-3D Bedienungsanleitung
SHAREBOT
SHAREBOT BIG Bedienungsanleitung
SHAREBOT
SHAREBOT 42 Bedienungsanleitung
SHAREBOT
SHAREBOT Kiwi-3D Bedienungsanleitung
