SHAREBOT Kiwi-3D Bedienungsanleitung
1 | Introduction
4
Dear Sharebot operator, we are thrilled that you have chosen to side in the fore-
front of this new industrial revolution. As with any new technology, the pioneers
like yourself are the ones who’ll drive true innovations. Your new Sharebot 3D
printer will make you free to create all the objects you can imagine. The new de-
sign of this Sharebot’s printer incorporates all the experience gained from previ-
ous models of Sharebot 3D printers and we’re extremely proud of this new model.
Your input will help us to constantly improve Sharebot 3D printers and it will
innovation so please share your experiences on www. kiwi3dworld.com
We look forward to see what you build!
Sharebot team
KIT contents: if at the end of the installation you will exceed some of the parties,
keep them because they’ll be useful as spare parts in the future. cosa realizzerai!
1 | Introduction
2 | Parts List
7
FOIL KEY:
A – Main structure
B – Bottom tray
C – Z Plan
D – Printing bed
F - carriage X
O – Hotend Plate
P - Lead-carrier Y Z
Q – Lead-carrier X
9
METHACRYLATE CARTER KEY:
A – Frontal carter
B – Head carter
C – Right carter
E- Rear carter
G – Right deep end carter
P1 – Reel carrier
P2 - Reel carrier
P3 - Reel carrier
P4 - Reel carrier
2 | Parts list 2 | Parts list
10 11
12
2 | Parts list
2 | Parts list
3 | Assembling the base
The screws can become loose due to shock and vibration: to avoid spontaneous
loosening of the screws it is recommended that you put brakes on all screws threads
between the threaded couplings. Tip: Loctite 221-brakes low-resistance threaded for
remember you each time where to apply this trick. For the lubrication of worm of the
Z axis, bearings and guides we recommend the use of vaseline oil or sewing machine
oil. The ShareBot Kiwi-3D assembly Kit, is an advanced kit and requires good manual
dexterity skills and ability to tin solder for a correct assembly.
2 | Lista delle Parti
3 | Assembling the base
Fig. 1
10. Fan 40x40
11. Screws M3x6 8
12. Screws M3x10 2
_
Fig. 2
Take the bottom plate of the printer and turn it so that the edges have relieved
geared down. Remove the plastic protective sheet.
_
Fig. 3
Take the four rubber pins, and separate them.
1
23
17
Fig. 4
Stick the 4 rubber pins to the base’s angles.
_
Fig. 5
position you can locate the holes. Pictured are highlighted with coloured areas:
purple for the target Z-guides, green for the Z axis engine, Orange for the control
card, yellow for the fan.
_
Fig. 6
Get 4 pads lock guides. Begin to position the plates block guide to 2 pairs on the
respective holes, and point it using 2 screws M3x6 for every lead carrier.
_
Fig. 7
To center the screws before thighten them, you can use the axis Z guides D8x338.
_
Fig. 8
_
Fig. 9
the base, using 4 screws M3x6. Do not tighten too strong or there’s the risk to dam-
age the nylon threads. In this case you don’t need to use the brakes-threads.
4
6
8
5
7
9
3 | Assembling the base
19
Andere Handbücher für Kiwi-3D
1
Inhaltsverzeichnis
Andere SHAREBOT 3D-Drucker Handbücher
SHAREBOT
SHAREBOT Next Generation Bedienungsanleitung
SHAREBOT
SHAREBOT Next Generation XXL+ Bedienungsanleitung
SHAREBOT
SHAREBOT BIG Bedienungsanleitung
SHAREBOT
SHAREBOT VIKING Bedienungsanleitung
SHAREBOT
SHAREBOT Q Dual Bedienungsanleitung
SHAREBOT
SHAREBOT 42 Bedienungsanleitung
SHAREBOT
SHAREBOT Kiwi-3D Bedienungsanleitung
