Sharp Actius PC-GP20 Betriebsanleitung

Supplement for PC-GP20

Notice for Users in the USA..…………………………………….2

Specifications....…………………………………………………..6

Wireless LAN..……………………………………………………7

Troubleshooting for Wireless LAN ...…………………………10

Re-installation Instructions………………………………….....12

Errata……...…………………………………………………….16

Notice for Users in the USA

FCC Statement

WARNING - FCC Regulations state that any unauthorized changes or modifications

to this equipment not expressly approved by the manufacturer could void the user’s

authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

A shielded I/F cable and included ferrite cores for LAN cable and IEEE 1394 cable

are required to insure compliance with FCC regulation for Class B computing

equipment.

• As an ENERGY STAR®Partner, SHARP has determined that this product meets

the ENERGY STAR®guidelines for energy efficiency.

Declaration of Conformity

SHARP PERSONAL COMPUTER, PC-GP Series

This device complies with part 15 of the FCC rules. Operation is subject to the following

conditions:(1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Responsible Party: SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430-2135

TEL: 1-800-BE-SHARP

About the Modem

This equipment complies with Part 68 of FCC rules. On the bottom of this equipment

is a label that contains, among other information, the FCC registration number and

ringer equivalence number (REN) for this equipment. If requested, this information

must be provided to the telephone company.

The modem jack of this equipment complies with Sub-part F of Part 68 of FCC rules.

The REN is used to determine the quantity of devices which may be connected to the

telephone line. Excessive RENs on the telephone line may result in the devices not

ringing in response to an incoming call. In most, but not all areas, the sum of the

RENs should not exceed five (5.0). To be certain of the number of devices that may

be connected to the line, as determined by the total RENs contact the telephone

company to determine the maximum REN for the calling areas.

If the terminal equipment causes harm to the telephone network, the telephone

company will notify you in advance that temporary discontinuance of service may be

required. But if advance notice isn't practical, the telephone company will notify the

customer as soon as possible. Also, you will be advised of your right to file a

complaint with the FCC if you believe it necessary.

The telephone company may make changes in its facilities, equipment, operations, or

procedures that could affect the operation of the equipment. If this happens, the

telephone company will provide advance notice in order for you to make the

necessary modifications in order to maintain uninterrupted service.

If trouble is experienced with this equipment, please contact Sharp Electronics Corp.

for repair and (or) warranty information (Refer to the end of this section). If the

trouble is causing harm to the telephone network, the telephone company may request

you remove the equipment from the network until the problem is resolved.

The equipment cannot be used on public coin service provided by the telephone

company. Connection to Party Line Service is subject to state tariffs. (Contact the

state public utility commission, public service commission or corporation commission

for information.)

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to

use a computer or other electronic device, including fax machines, to send any

message unless such message clearly contains in a margin at the top or bottom of each

transmitted page or on the first page of the transmission, the date and time it is sent

and an identification of the business or other entity, or other individual sending the

message and the telephone number of the sending machine or such business, other

entity, or individual. (The telephone number provided may not be a 900 number or

any other number for which charges exceed local or long-distance transmission

charges.) To program this information, refer to the manual of the communication

software.

For Wireless LAN Bundled Model

Wireless LAN / Modem Model Name: T60H424

FCC ID: MCLT60H42400

This device complies with part 15 of the FCC rules. Operation is subject to the

following conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

Warning

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount

of mercury.

Disposal of these materials may be regulated due to environmental considerations.

For disposal or recycling information, please contact your local authorities or the

Electronics Industries Alliance: www.eiae.org

It is the intent of Sharp that this product be used in full compliance with the copyright

laws of the United States and that prior permission be obtained from copyright owners

whenever necessary.

Product Information and Customer Assistance

For Product Information and Customer Assistance:

Call: 1-800-BE-SHARP (237-4277)

Sharp Systems of America

5901 Bolsa Avenue, Huntington Beach, CA 92647

Home Page: http://www.sharp-business.com

E-mail address: support@sharp-business.com

Wireless LAN Precautions

• Do not communicate with wireless LAN in specific environment where radio-

susceptible equipments are nearby such as on airplanes, in hospitals, etc.

• Do not touch the antennas while communicating.

• Keep the distance at least 20cm between the antennas and your body while

communicating.

Specifications

Parts PC-GP20

CPU Intel Desktop Pentium 4 2A GHz

Primary cache 8KB (Integrated with CPU)

Secondary cache 512KB (Integrated with CPU)

ROM Including system BIOS,VGA BIOS, Plug&play compliant BIOS

RAM System DDR-SDRAM 256MB (expandable up to 512MB)

Video 16MB (default setting. shared with system memory)

Panel Active Matrix (TFT) color LCD 15”(38.1cm)

Video controller SiS 650

Display

Resolution/color 1024 x 768 dots/16M colors by dithering function

Keyboard IBM compatible keyboard

Pointing device Glide pad (touch-sensitive control pad with 2 buttons )

Drive Hard disk IDE interface 40GB

Floppy disk 3.5", 1.44MB/720KBOptical CD-R/RW Reading:24x (max.) Writing: 16x Re-writing: 10x (max.)

DVD-ROM Reading:8x (max.)

PC card slot Type II ×1(PCMCIA 2.1 and CardBus compliant)

SD card slot SD card slot ×1

Smart Media card slot Smart Media card slot ×1(3.3V compliant)

Audio system Monaural microphone, stereo speakers, sound system compliant with AC97

audio

Audio Audio output jack (stereo, S/PDIF compliant), external microphone jack

(monaural)

Video External display connector, S video connector

I/O ports

Others 4 USB ports, parallel port. IEEE 1394 port

Modem Data: 56Kbps (receive), 33.6Kbps (send), Fax: 14.4Kbps

LAN 100 BASE-TX/10 BASE-T

Radio Technology DSSS (IEEE802.11b) compliant

Frequency Band 2400 – 2483.5MHz

Operating Channels 11 channels

Wireless LAN

Data Rate 1 / 2 / 5.5 / 11 Mbps

AC adapter 100-240V, 50-60 Hz

Battery Rechargeable Li-ion battery

BatterylifeApproximately1.6 hours

*Battery life varies depending on usage

Turned off/hibernation: Approximately 3.0 hours

*Charging time varies depending on usage

Power

Battery charging

time

Turned on: Approximately 6.0 hours

*Charging time varies depending on the usage

Dimensions 324mm wide x 277mm deep x 41mm (min.) /51mm (max.) high (12.7" x

10.9" x 1.5" (min.)/1.9" (max.) )

*No protuberance is included.

Weights Approximately 3.8 kg (8.3 lbs)

Temperature

10°C to 35°C (50°F to 95°F)Operating

environment

Humidity 20% to 80% (non-condensation)

Wireless LAN

Your computer has an integrated wireless LAN function compliant with IEEE

802.11b standard. You can access the network by the wireless LAN.

See the attached specification sheet to confirm your computer has a built-in wireless

LAN function.

There are two kinds of wireless networks: a network using an access point and a peer-

to-peer wireless network. You can connect your computer to a wired LAN or the

Internet through an access point that is also compliant with IEEE 802.11b standard.

Peer-to-peer wireless network consists of a number of computers each equipped with

wireless networking interface. Each computer can communicate directly with other

wireless enabled computers.

The range to give reliable performance and the quality of connection

vary depending on the environment where you perform.

To communicate with the wireless LAN, activate the integrated antennas with the

following steps.

Activate Antennas

You can enable/disable the antennas by pressing Fn +F1 key combination. When the

antenna indicator ( ) lights green, the antennas are enabled. When the indicator light

is off, they are disabled.

ntenna Indicator

Connecting to the Internet via an Access Point

You can connect your computer to the Internet or a wired network via an access point

supporting IEEE 802.11b. Refer to the manual of the access point or consult your

network administrator if you are not sure.

Communicating with Other Computers

• Confirm each computer is enabled for wireless LAN first.

• Make sure to log on the computer as a member of the Computer

administrators group. Otherwise, you cannot set or change some

settings for wireless LAN.

1. Click start – Control Panel.

2. Click Network and Internet Connections – Network Connections. If Classic view

is selected, click Network Connections.

3. Select Wireless Network Connection; then, click Change settings of this

connection of Network Tasks.

4. Double-click Internet Protocol (TCP/IP) in This connection uses the following

items.

5. In Internet Protocol (TCP/IP) Properties dialog box, select Use the following IP

address and set a unique IP address to 192.168.1.2 through 192.168.1.254 and

the Subnet mask to 255.255.255.0; then, click OK.

• The IP address of each computer should be unique.

• The Default gateway can be blank.

6. Click Wireless Networks tab; then, click Advanced button in the lower right of the

dialog box. Advanced dialog box appears.

7. Select Computer-to-computer (ad hoc) networks only; then, click Close.

8. Click Add… button in Preferred networks of Wireless Network Connection

Properties dialog box.

9. Type a name of the network in Wireless Network Properties dialog box.

Confirm your computer and other computers are connecting to the same

network.

10. Click OK twice; then, close the Control Panel.

11. Configure the network by setting the name of your computer and workgroup.

To communicate with other wireless enabled computers, set the computer

name and the workgroup name. The computer name should be unique

and the workgroup name should be same as others.

Confirming the Status of the Wireless Connection

Before performing the following instructions, confirm the devices that you want to

communicate with are enabled for wireless LAN.

1. Click Wireless Network Connection icon ( or ) on the taskbar. If you

cannot find the icon click to show all kinds of icon. Connect to Wireless

Network dialog box appears. If Wireless Network Connection Status dialog box

appears, go to Step 4.

2. Select a network you want to access in Available networks in Connect to

Wireless Network dialog box; then, click Connect button.

• When the network name you want to access does not appear, click

Advanced tab; then, Refresh button of Available networks in Wireless

Network Connection Properties dialog box; then, click OK.

• When the WEP security of the wireless network that you want to

access is enabled, make sure to enter Network key and select Key

format and Key length correctly. (Click Add… button in Wireless

Networks tab of Wireless Network Connection Properties dialog box.)

3. Click Wireless Network Connection icon ( ) on the taskbar.

4. In Wireless Network Connection Status dialog box, confirm your connection

status.

• When the quality of connection is poor, adjust the distance between the

computer and other devices or the access point you are communicating

with and/or the facing direction of the computer.

• The connection quality is shown the number of green signals ( ).

The more signals light on, the better quality is given to the computer.

Troubleshooting for Wireless LAN

Question: Why can't I detect the access point on my computer?

• Confirm the access point is powered on.

• Confirm the antenna indicator is on.

• Restart your computer.

• Confirm your computer is enabled for the wireless LAN.

• Detect the access point by following the steps below:

1. Click start – My Computer.

2. Select My Network Places in Other Places; then, View network connections in

Network Tasks. Network Connections dialog box appears.

3. Right-click Wireless Network Connection; then, click Disable.

4. Right-click Wireless Network Connection; then, click Enable.

• When you have more than one access points, your computer may be connected to

other than right one you want to access. Follow the steps bellow.

1. Right-click ( ) icon on the taskbar; then, click View Available Wireless

Networks.

2. Select the desired network in the Available networks list; then, click Connect

button.

Question: Why can't I connect to the network via an access point?

• Confirm Any available network (access point preferred) is selected in Networks to

access of Advanced dialog box. (To open Advanced dialog box, refer to

Communicating with Other Computers section on page 8.)

• Confirm the ESSID of your computer matches the ESSID of the access point you

want to communicate with.

• Confirm the WEP key is correctly entered if the WEP security of the access point is

enabled.

Question: Why can't I communicate with other computers with a wireless

LAN?

• Confirm each computer is enabled for wireless LAN.

Andere Handbücher für Actius PC-GP20

Inhaltsverzeichnis

Andere Sharp Laptop Handbücher

Sharp

Sharp PC-9300 Bedienungsanleitung

Sharp

Sharp Actius PC-MC22 Bedienungsanleitung

Sharp

Sharp PC-AR10 Bedienungsanleitung

Sharp

Sharp Actius PC-GP22W Bedienungsanleitung

Sharp

Sharp PC-A250 Bedienungsanleitung

Sharp

Sharp PC-9800T Bedienungsanleitung

Sharp

Sharp Actius PC-UM30W Bedienungsanleitung

Sharp

Sharp PC-MV10 Series Bedienungsanleitung

Sharp

Sharp PC-A290 Bedienungsanleitung

Sharp

Sharp PC-AX Series Bedienungsanleitung

Sharp

Sharp MV12W - Actius - PIII-M 1 GHz Bedienungsanleitung

Sharp

Sharp PC-AL27 - Actius AL27 - Mobile Athlon 64 1.6... Bedienungsanleitung

Sharp

Sharp AV18P - Actius - Athlon XP-M Bedienungsanleitung

Sharp

Sharp Actius PC-GP20 Bedienungsanleitung

Sharp

Sharp Actius PC-UM32W Bedienungsanleitung

Sharp

Sharp Actius PC-GP20 Bedienungsanleitung

Sharp

Sharp Actius PC-MV10 Bedienungsanleitung

Sharp

Sharp Actius PC-TN10W Bedienungsanleitung

Sharp

Sharp PC-A280 Bedienungsanleitung

Sharp

Sharp Actius PC-MV14 Betriebsanleitung

Sharp

Sharp Actius PC-AV18P Bedienungsanleitung

Sharp

Sharp Actius PC-UM20 Bedienungsanleitung

Sharp

Sharp PC-GP10 Series Bedienungsanleitung

Sharp

Sharp Actius PC-RD20 Bedienungsanleitung

Beliebte Laptop Handbücher anderer Marken

HP ze2401xt - Pavilion Notebook PC Bedienungsanleitung

Velocity

Velocity NoteMagix M10 Bedienungsanleitung

Dell

Dell Alienware 17 R2 Bedienungsanleitung

Toshiba

Toshiba A105-S2236 Bedienungsanleitung

HP ENVY 17 Handbuch

Winbook

Winbook LM Bedienungsanleitung

Dell

Dell Inspiron 1464 Bedienungsanleitung

Dell

Dell Inspiron 15R 5537 Bedienungsanleitung

HP PROBOOK 4520S Handbuch

Dell

Dell Latitude ATG D620 Bedienungsanleitung

Sony

Sony VAIO PCG-FX270 Bedienungsanleitung

Dell

Dell Latitude 7310 Bedienungsanleitung

Dell

Dell Precision GU806 Bedienungsanleitung

Sony

Sony VAIO PCG-R505JLK Bedienungsanleitung

Lenovo

Lenovo THINKPAD X32 Bedienungsanleitung

HP Compaq tc4200 Kurzanleitung

Toshiba

Toshiba mini NB300 Bedienungsanleitung

Lenovo

Lenovo ThinkPad X201 Tablet Handbuch