Sharp SD-2060 Bedienungsanleitung

ELECTROSTATIC

COPYING MACHINE

MODEL

SD-2060

Page

KEY OPERATOR’S GUIDE

•KEY OPERATOR CODE

NUMBER (P19)

•KEY OPERATOR

PROGRAMS

•OPTIONAL COUNTER

COMMANDER (SF-EA13)

•KEY OPERATOR

ASSISTANCE CALL

Downloaded from: http://www.usersmanualguide.com/

This KEY OPERATOR’S GUIDE contains all of the programs

and programming information for use by the Key Operator.

The programs allow the Key Operator to tailor many functions

of the SD-2060 for specific modes of operation. These pro-

grams can only be accessed after a Key Operator Code

Number has been entered.

Please familiarise yourself with this entire guide. Keep it

handy, and refer to it as needs arise for the information you

will need to keep the SD-2060 operating smoothly.

CONTENTS Page

●KEY OPERATOR CODE NUMBER (P19).................... 2

●Registering the Key Operator Code Number............. 2

●KEY OPERATOR PROGRAMS ....................................3

●Using the Key Operator Programs .............................5

●OPTIONAL COUNTER COMMANDER (SF-EA13) .... 23

●Loading Printer Paper ..............................................23

●For Printing Data through Key Operator Programs . 24

●KEY OPERATOR ASSISTANCE CALL ..................... 25

Downloaded from: http://www.usersmanualguide.com/

KEY OPERATOR CODE NUMBER (P19)

A Key Operator Code Number must be registered before using the

key operator programs. The Key Operator must remember this

number. Only this registered number will allow access to the key

operator programs. Registering the Key Operator Code Number

Press the CLEAR/STOP key, the INTERRUPT key, and

the CLEAR/STOP key again.

●The following message will appear.

ENTER KEY OPERATOR CODE. –––––

Enter 0 five times using the 10-key pad.

●As each 0 is entered, the dashes on the message will change

to asterisks.

●When the entry is complete, a “P” will appear on the COPIES

SELECTED display and the following message will appear.

INPUT A PROGRAM NUMBER, AND PRESS

START.

Enter the number 19 using the 10-key pad and press

the START key.

●The following message will appear.

P19: KEY OPERATOR CODE NUMBER CHANGE.

FROM 00000 TO –––––, AND PRESS START.

Choose a new 5-digit code number and enter it using

the 10-key pad.

Press the START key.

●The code number will change from the factory setting to the

new setting.

●“P” will appear on the COPIES SELECTED display.

To continue with other key operator programs, enter

the appropriate program code number.

To exit the key operator program mode, press the

CLEAR ALL key.

<P006>

ERA

CHAN

START

C /

CLEAR/STOP

789

AUDIT

CLEAR

123

CLEAR/STOP

0 / C /

COPIES SELECTED

<P036>

<P007>

789

AUDIT

CLEAR

123

CLEAR/STOP

0 / C /

INTERRUPT

AUDIT

CLEAR

CLEAR/STOP

0 / C /

Downloaded from: http://www.usersmanualguide.com/

KEY OPERATOR PROGRAMS

A complete list of all Key Operator Programs is provided below.

These programs can only be accessed by first entering the Key Op-

erator Code Number.

If the optional Card Counter (SF-EA11) is installed, programs 10 to

16 and 18 cannot be accessed.

Code No. Program Name Function Page No.

P10 Auditing Mode Enables or disables the basic auditing mode for 6

copier access.

P11 Copies by Account Displays or prints the total number of copies made 6

against account numbers.

P12 Billing by Account Displays or prints the accumulated cost of copies 7

by account number.

P13 Billing Clear Mode Clears all audit accounts or selectively clears indi- 8

vidual accounts.

P14 Account Number Enters account numbers, clears account numbers, 9

Control changes an account number, or prints all assigned

account numbers.

P15 Price/Copy Setting Sets up to 3 levels of price per copy against ac- 11

count numbers.

P16 Account Limit Sets the maximum number of copies which can be 12

Setting made against an assigned account number.

P17 Machine Identifica- Enters or prints the machine number. 13

tion Number

P18 Account Number Guards against trial and error entering of audit ac- 13

Security count numbers.

P19 Key Operator Code Changes the Key Operator Code Number. 14

Number Change

P20 Auto Exposure Lightens or darkens copies in the automatic expo- 14

Adjust sure mode.

P21 Power Up Timer Activates and sets a time interval after which the 14

copier automatically turns off.

P22 Toner Save Mode Reduces toner consumption. 14

P23 Auto Clear Setting Sets a time interval after which the copier returns to 15

the initial settings.

P24 Add or Change Adds or changes reduction and enlargement preset 15

Extra Presets copy ratios.

P25 Limit of Maximum Sets the limit of maximum copies to be selected. 16

Copies Selected

P26 Initial Margin Shift Sets the initial margin shift values. 16

Setting

P27 Erase Width Sets the amount of the erase area. 16

Adjustment

Downloaded from: http://www.usersmanualguide.com/

Code No. Program Name Function Page No.

P28 Initial Status Sets the copier’s initial settings in the ready condi- 17

Setting tion.

P29 Total Copy Count Recalls the total copy counts of the copier, RADF, 17

duplex module, and staple sorter.

P42 Right/Left Shift Determines whether shift direction change is to be 18

Direction Selection allowed.

P43 Erase Mode Sets the initial mode for erase function. 18

Selection

P44 Restrict Storage Prevents insert pages from being stored in job 18

of Inserts in Job memory.

Program Memory

P45 Message Time Sets the length of time that messages are dis- 18

Setting played.

P46 Disable Operation Prevents the copier from being started by people 19

other than key operator.

P70 Disabling of Auto Prevents automatic paper selection. 19

Paper Selection

P71 Disabling of Auto Prevents automatic switching between the paper 19

Tray Switching trays.

P72 Bypass-Tray Prohibits the use of the bypass tray during duplex 19

Prohibited in copying.

Duplex Copy

P73 Disabling of Job Prevents stored programs from being altered. 20

Program Changing

P74 Disabling of Prevents the use of the RADF when it malfunc- 20

Document Feeder tions.

P75 Disabling of Duplex Temporarily prevents the duplex system from ope- 20

Copying rating when it malfunctions. Allows the use of the

copier but not the duplex system.

P76 Disabling of Prevents damage to the stapler while awaiting re- 20

Stapler pair service.

P77 Disabling of Prevents the selection of COVERS and INSERTS 21

Covers and Inserts mode.

P78 Restricted Access Provides access to paper trays only for adding 21

to Paper Trays paper or during misfeed removal.

P90 Display the List of Sequentially displays all available programs. 21

All P Codes

P92 P Code List Sequentially prints all available programs. 22

Printout

KEY OPERATOR PROGRAMS

Downloaded from: http://www.usersmanualguide.com/

Using the Key Operator Programs

Press the CLEAR/STOP key, the INTERRUPT key, and

the CLEAR/STOP key again.

●The following message will appear.

ENTER KEY OPERATOR CODE. –––––

Enter the key operator code number.

●The dashes on the message will change to asterisks. If the

enteredcodenumber is correct,“P” will appearon the COPIES

SELECTED display.

Enter the desired 2-digit program code number and

press the START key.

●If a mistake is made during entry, press the CLEAR/STOP key

to clear the entry.

●The message display will show the number and name of the

program.

●In some programs, the current setting will be displayed on the

COPIES MADE display and highlighted in the message dis-

play.

Follow instructions for the program.

●When all steps for the program have been completed or when

the PROGRAM key is pressed to exit the program, “P” will ap-

pear on the COPIES SELECTED display so that another pro-

gram can be selected.

To exit the key operator program mode, press the

CLEAR ALL key.

<P006>

PROGRAM

CLEAR ALL

INTERRUPT

CA 4

COPIES SELECTED

789

AUDIT

CLEAR

123

CLEAR/STOP

0 /

INTERRUPT

AUDIT

CLEAR

CLEAR/STOP

0 / C /

KEY OPERATOR PROGRAMS

Downloaded from: http://www.usersmanualguide.com/

KEY OPERATOR PROGRAMS

P10 Auditing Mode

Program P10 is used to enable or disable the basic auditing mode of

operation.

When disabled, the message in the display will be “READY TO

COPY.” Access to copying is open to any operator.

When enabled, the message in the display will be “ENTER YOUR

ACCOUNT NUMBER -----.” Copying in this state is limited to oper-

ators with an assigned 5-digit account number.

A maximum of 500, 5-digit account numbers can be assigned. Use

Key Operator Program P14 to assign account numbers.

P11 Copies by Account

Program P11 is used to display or print the total number of copies

made against each account number. For printing the data, an option-

alcounter commander SF-EA13is needed.(Seepage 23for instruc-

tions to print.)

When P11 is entered, the following message will appear.

P11: COPIES BY ACCOUNT.

1.PRINT 2.DISPLAY(SINGLE)

To print accounts

1. Press key 1.

●The following message will appear.

PRINT: 1.ALL ACCOUNTS.

2.SINGLE ACCOUNT.

2. To print all accounts, press key 1.

To print a single account, press key 2, enter the

account number, and press the START key.

3. Press the START/STOP key of the counter commander.

To sequentially display accounts

1 Press key 2.

2. Press the SCROLL DISPLAY key to advance through

the accounts.

●The account numbers and the number of copies made against

each account will be sequentially displayed.

3. Press the PROGRAM key to exit the program.

<P010>

<P009>

Downloaded from: http://www.usersmanualguide.com/

KEY OPERATOR PROGRAMS

To display an individual account

1. Press key 2.

●The following message will appear.

INPUT ACCOUNT NUMBER TO BE DISPLAYED

AND PRESS START.

ACCOUNT NUMBER NUMBER OF COPIES MADE

––––– –––––

2. Enter the account number and press the START key.

●The number of copies made will be displayed.

3. Continue with step 2 for other account numbers.

Press the PROGRAM key to exit the program.

P12 Billing by Account

Program P12 is used to display or print the accumulated cost of cop-

ies made when a relevant price per copy has been set using pro-

gram P15. For printing the data, an optional counter commander SF-

EA13 is needed. (See page 23 for instructions to print.)

When P12 is entered, the following message will appear.

P12: BILLING BY ACCOUNT.

1.PRINT 2.DISPLAY(SINGLE)

To print accounts

1. Press key 1.

●The following message will appear.

PRINT: 1.ALL ACCOUNTS.

2.SINGLE ACCOUNT.

2. To print all accounts, press key 1.

To print a single account, press key 2, enter the

account number, and press the START key.

3. Press the START/STOP key of the counter commander.

To sequentially display costs

1. Press key 2.

2. Press the SCROLL DISPLAY key to advance through

the account numbers.

●The account numbers and the accumulated cost of copies

made against each account will be sequentially displayed.

3. Press the PROGRAM key to exit the program.

<P014>

<P015>

<P010>

Downloaded from: http://www.usersmanualguide.com/

KEY OPERATOR PROGRAMS

To display the cost of a particular account

1. Press key 2.

●The following message will appear.

INPUT ACCOUNT NUMBER TO BE DISPLAYED

AND PRESS START.

ACCOUNT NUMBER BILLING

––––– –––––

2. Enter the account number and press the START key.

●The accumulated cost of copies made will be displayed.

3. Continue with step 2 for other account numbers.

Press the PROGRAM key to exit the program.

P13 Billing Clear Mode

Program P13 is used to clear all audit accounts or to selectively clear

individual accounts.

When P13 is entered, the following message will appear.

P13: BILLING CLEAR MODE.

1.ALL ACCOUNTS. 2.SINGLE ACCOUNT.

To clear all accounts

Press key 1.

To clear a single account

1. Press key 2.

●The following message will appear.

INPUT AN ACCOUNT NUMBER TO BE CLEARED.

ACCOUNT # –––––, PRESS START TO CLEAR.

2. Enter the account number to be cleared.

3. Press the START key.

4. Continue with steps 2 and 3 for other account num-

bers. Press the PROGRAM key to exit the program.

<P017>

<P018>

<P019>

Downloaded from: http://www.usersmanualguide.com/

Andere Handbücher für SD-2060

Inhaltsverzeichnis

Andere Sharp Drucker Handbücher

Sharp

Sharp AJ-1100 Einrichtungshandbuch

Sharp

Sharp DX-B350P Bedienungsanleitung

Sharp

Sharp AR-153E N Bedienungsanleitung

Sharp

Sharp PR-45M Bedienungsanleitung

Sharp

Sharp AR-C360P Konfigurationshandbuch

Sharp

Sharp AR-C200P - Color Laser Printer Bedienungsanleitung

Sharp

Sharp AR-M351N Bedienungsanleitung

Sharp

Sharp AR-PK6 Bedienungsanleitung

Sharp

Sharp ER-01PU Bedienungsanleitung

Sharp

Sharp MX-M260 Einrichtungshandbuch

Sharp

Sharp AR-M350N Bedienungsanleitung

Sharp

Sharp AR-M550N Service-Handbuch

Sharp

Sharp MX-C400P Bedienungsanleitung

Sharp

Sharp AL-1000 Series Bedienungsanleitung

Sharp

Sharp MX-2301N Bedienungsanleitung

Sharp

Sharp MX-M310 Einrichtungshandbuch

Sharp

Sharp MX-2640N Kurzanleitung

Sharp

Sharp AR-CF2 Bedienungsanleitung

Sharp

Sharp MX-C300P Bedienungsanleitung

Sharp

Sharp DX-C200P Operation Montageanleitung

Sharp

Sharp MX-B468P Bedienungsanleitung

Sharp

Sharp MZ-80P4 Bedienungsanleitung

Sharp

Sharp DX-B350P Bedienungsanleitung

Sharp

Sharp MX-B380P Installations- und Betriebsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung