Sharp WH-T36E Bedienungsanleitung

SHARP SERVICE MANUAL

ELECTRIC WATER HEATER

MODEL WH-T36E

WH-T39EP

WH-T46E

In the interests of user-safety (Required by safety

regulations in some countries) the set should be restore

to its original condition and only parts identical to

thosespecifiedshouldbeused.

SHARP CORPORATION

TABLE OF CONTENTS

NAME OF PARTSAND SPECIFICATIONS ......................................................................

EXTERNAL DIMENSION ...................................................................................................

CAUTION FOR USE .........................................................................................................

HOW TO USE ...................................................................................................................

CIRCUIT DIAGRAM ...........................................................................................................

INSTALLATION ADVICE ...................................................................................................

POWER SUPPLY INSTALLATION ....................................................................................

SHOWER SET ..................................................................................................................

REPLACING METHOD FOR MAIN PARTS .......................................................................

TROUBLESHOOTING .......................................................................................................

CIRCUIT DIAGRAM (PCB-A) ............................................................................................

SERVICE PARTS LIST ......................................................................................................

Page

5-8

8-9

10-15

18-24

NAME OF PARTS

SPECIFICATION

Model

Voltage(V)

Ratedfrequency (Hz)

Powerconsumption (W)

Water supply

Watersupply temperature control

Min. Water Pressure (MPa)

Max. Water Pressure (MPa)

Dimension (W x D x H) (mm.)

Weight(kg)

Note : Water temperature is around 25 C. Water flow rate : 2.3 liters/min.

One Point system

Electroniccontrol water temperature 50C(approximate)

0.02 (0.21 Bar)

0.34 (3.39 Bar)

245 x 112 x 380

2.7

220

: 1 MPa = 10.2 kg/cm2.

Main Breaker

ELB Checker Button

Shower Stand

Water Volume Knob

Push ON-OFF Button

ELB Lamp

Power Lamp

Control Lamp

Temp. Control Knob

Shower

Shower Hose

Body

Main Water Valve

Earth Ground

Breaker Angle Support

WH-T36E WH-T39EP WH-T46E

3,500 4,500

Temp. Level Lamp

EXTERNAL DIMENSION

Front

Fig. 1

Neverinstall water valve orfaucetat hot water outlet.

Never spray water to the electric water heater, do not put wet towels on it.

Nevercoverthe shower set with hand ortowels,donot fold down shower hose.

CAUTION FOR USE

Watervalve

Water

outlet

Water inlet

Fig. 2

Fig. 3

Fig. 4

(Unit in mm.)

380

245

Side Back

112

178

380

BEFOREUSE

Theelectrichome shower unit must earthed.

Special skill is required. Never try to repair the unit by yourself.

1. Turn on the MAIN WATER VALVE.

2. Switch on the MAIN BREAKER.

3. Push up the breaker angle support, if it is down.

4. Pressthe PUSH ON-OFFBUTTON,roomtemperature water will flow in and the ELB lamp lights up.

5. Turnonthe WATERVOLUMEKNOB to set the preferable water flow rate(seedetail“TEMPERATURE

ADJUSTMENT”).

6. Turn on theTEMP. CONTROLKNOBto set the preferable temperature, indicationTEMP. LEVELLAMP

andPOWERLAMPlightsup,thehotwaterwill flow out (see detail“TEMPERATUREADJUSTMENT”).

7. After use, press the PUSH ON-OFF BUTTON to turn off water. For next time, just press the

PUSHON-OFF BUTTON, the volume and temperature ofwaterwillbe as first set.

Note

In case of electricity cut off or suspension of water supply, turn off theTEMP. CONTROL KNOB, press

thePUSH ON-OFF BUTTONand turn offMAINBREAKER beforeleavinga bathroom.

TEMPERATUREADJUSTMENT

1. TEMP.CONTROLKNOB.

1.1 TheTEMP.CONTROLKNOBis at “OFF” position, the

watertemperature will remainatroom temperature.

1.2 When the TEMP. LEVELLAMP (yellow) light up : Low level

TEMP. LEVEL LAMP (orange) light up :Medium level

TEMP. LEVEL LAMP (red) light up :High level

1.3 If water temperature islowerthanthe setting, the CONTROL

LAMP will blink. You may need to adjust the WATER

VOLUMEKNOBto decrease flow rate.

1.4 The CONTROL LAMP and POWER LAMP lights up,ifwater

temperature is to set.

1.5 When CONTROL LAMP to blink and POWER LAMP will

gooff,ifwatertemperatureis equal or higher than set.

HOW TO USE

2. WATERVOLUMEKNOB.

Turning the WATERVOLUMEKNOB clockwise to increase water volume.

Turning the WATER VOLUME KNOB counterclockwisetodecreasewater volume.

3. PUSH ON-OFF BUTTON.

Press the PUSH ON-OFF BUTTON (the ELB lamp lights up) the hot water flow out. To close, repress

thePUSHON-OFFBUTTON.

“ON” status : Button is lower than unit cover.

“OFF” status : Button is as high as unit cover.

ELB Checker

ELB Lamp

Control Lamp

Power Lamp

TEMP.Control

Knob

Push ON-OFF

Button

TEMP. Level Lamp

CIRCUIT DIAGRAM

INSTALLATION ADVICE

1. BEFORE INSTALLATION

Besureof sufficient water pressure.

Minimum water pressure : 0.02 MPa (0.21 Bar).

Maximum water pressure : 0.34 MPa (3.39 Bar).

Water pressure measurement. Please see illustration; water must flow out of the pipe beyond

2.3 meters above the faucet.

2. INSTALLATION

1. The body unit installation.

The body unit must be installed to wall as illustration.

About 2.3 meters

Fig. 5

Fig. 6

The shower installation must be over 1.50 meters from the ground.

Fig. 7

3. Install electric water heater on wall.

Drill 2 holes in the wall with size 6 millimeters, 25 millimeters in depth, distant 178 millimeters

Put fitting in the holes.

Drivescrewsinto the upper fitting and leave screws about 8-10 millimetersinlength.

Hang the equipment with the screws and mark the lower points to drill the other 2 holes.

Drill 2 holes and put fittings, then drive all screws firmly.

Fig. 10

Screw Fig. 8

2. Removing the body unit cover.

Remove the screw at the bottom of the unit.

Remove the front plate first at the bottom.

25 mm.

6 mm.

Fig. 9

Over 1.50 meters

178 mm.

4. The unit cover assembly.

Remove the TEMP. CONTROL KNOB and PUSH ON-OFF BUTTON as illustration.

Push unit cover on to body unit until they are locked.

Drive screw cover unit and body unit. Insert the TEMP. CONTROL KNOB and

PUSH ON-OFF BUTTON.

6. Shower stand installation :

After installing shower stand, the shower set should be in the lower level with body unit.

Fig. 13

Temp. Control Knob

Body Temp. Control Knob

Push ON-OFF Button

Screw

Push off the body

Push on at the top

Fig. 11

Fig. 12

Shower

Shower spacer

Shower hose

5. The shower assembly.

Turn joint the shower hose counterclockwise with the shower.

Joint

3. WATER PIPE

1. Turn the joints between body unit, the WATER VOLUME KNOB and SHOWER HOSE manually.

Neveruseother tools to avoid breaking plastic parts.

2. When driving screws, use power less than 40 kgf.cm.

3. Pipinginstallation (as illustration).

Fig. 14

Main breaker

Bathroom

Fig. 15

POWER SUPPLY INSTALLATION

1. Be sure to cut off the main power supply switch every time before starting any electrical work.

Useinsulateddoublewire gage size at least 4 square millimeters. (Model WH-T36E, WH-T39EP)

andsize6 square millimeters (Model WH-T46E) for power supply line.

Connecting supply line from the main distribution control unit to the cut off breaker.

(Thisbreaker should be installed outsidethebathroomand connected permanently).

Water inlet

Filter

O-ring

Valve

Length of water inlet hose at least 15 cm.

Filter

Shower hose Water volume

Shower

2. Connecting supply line can be done in 2 ways (see illustration below) which are punching on the

lateral rubber grommet at the side or the back of cover unit.

Punching at the back of cover unit.

Fig. 16

Punching at the side of cover unit.

TooIing for assembly

Min 30 cm.

Ground

Ground rod Fig. 18

5. Make sure that the grounding resistance should be less than 5 Ohm.

6.Incase grounding resistance is over 5 Ohm the additional ground rods may be needed, where as the

distance between both rods is at lest ground rod length.

4. How to install the ground rod.

Aseparately provided ground rodshouldbe piled down intothehigh moisture ground.

Theground rod should be atleast30centimeters placed underneath thegroundlevel.

The ground rod is not less than 16 millimeters diameter and 240 centimeters in length.

Strip out the wire insulator, connect it to the ELB BREAKER terminal, Live wire (high potential) must

be connected to the “L” and Neutral line to the “N”, secure firmly with a screwdriver.

(Torque of about12kgf.cm.shouldbe applied).

3. The line of “L” and “N” must be carefully and correctly connected to the corresponding pole;

otherwise, it may affect the circuit and consequently causes damage to the unit or electrical harm.

Fig. 17

Torque of about 12 kgf. cm.

50 mm.

20 mm.

12 mm. 30 mm.

REPLACINGMETHODFORMAINPARTS

1. Turn out the joint body between the body with the shower hose manually. Never use other tools to

avoid breaking plastic parts.

REMOVE OF SHOWER HOSE

Fig. 20

SHOWER SET

By turning shower cover, water flow can be adjusted in 5 types.

Fig. 19

JET

COMFORT

FOAMY

SPRAY

FRESHEN

Mark shows the patterns of

water flow at the chose position

LEFT RIGHT

Body

Shower hose

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sharp Boiler Handbücher

Sharp

Sharp WH-A55 Bedienungsanleitung

Sharp

Sharp WH-236E Bedienungsanleitung

Sharp

Sharp WH-237DP Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung